05-01-2012, 11:54 AM | #1 |
chevy pride
|
black fender letters
where can i buy some for a good price anyone know.
__________________
check out ky speeds fb page https://www.facebook.com/kyspeed |
05-01-2012, 12:55 PM | #2 |
Shadow Gray '19 ZLE M6
|
emblempros.com <--forum sponsor and great products
__________________
2019 ZL1 1LE | M6 | SGM | PDR | CF Dash | Nav | Wheel Locks
PPF | Paint Correction | ZL1 Addons Rock Guards | ZL1 Addons Lift Pads | ZL1 Addons Feather Lite Tow Hook | JWM Smoked Sidemarkers | Wildhammer Smoked Rear Reflectors | JWM License Plate LEDs | RotoFab CAI | ADM IC Reservoir v2 | BC Forged RZ05 | SPL Toe Arms | BW Brake Deflectors | CMS Roll Bar | Schroth Profi II ASM Harnesses . Sold: '99 Trans Am (bolt-ons & cam) | '00 WS6 (bolt-ons, heads, cam, 12 bolt) | '05 CTS-V (bolt-ons, short throw) | '10 SS/RS M6 (short throw, CAI, coilovers, LTs, catback, JRE tune) | '01 WS6 YouTube |
05-01-2012, 01:51 PM | #3 |
|
You could always plasti dip them. A can costs $6 at home depot. You can plasti dip your tail light bezels at the same time!
__________________
|Trifecta Tune|Custom Magnaflow Exhaust|Cold Air Inductions C.A.I.|BBK LTs w/ HFC|Anvil Rear Notch Glossy CF Spoiler|Body Color Heritage Grille|10 spoke polished ZL1 replica wheels|VMAX ported TB|RS Headlights|Night Owl RGB Halos
|
05-01-2012, 02:01 PM | #4 |
|
|
05-01-2012, 07:35 PM | #5 | |
Two Miles An Hour
Drives: SIM 2LT RS Join Date: May 2010
Location: chicago
Posts: 1,209
|
Quote:
Highly recommend this route. Much cheaper and the letters will retain the oem shape and not be blocky.
__________________
expect nothing, but take everything |
|
05-01-2012, 08:00 PM | #6 |
Emerald Coast Camaros
Drives: A lot of show, not much go. Join Date: Mar 2011
Location: Emerald Coast
Posts: 3,388
|
This.....or if you want it even more permanent use regular spray paint on them.
|
05-01-2012, 09:24 PM | #7 |
COTW 5/27/13
|
This can pick up a set (2 pair) for about $25 and anothe $5 for spray paint. best way IMO
__________________
622RWHP/512FTLBS on 91 octane 2.9l Whipple 4" pulley. Vengance VRSP3 cam. Lots of BMR & AAC. Body work by Gary's Customz. Nic D tuned My build thread |
05-01-2012, 09:38 PM | #8 |
2016 Camaro 1LT 2.0T
Drives: Nemesis Join Date: Feb 2011
Location: Albuquerque, NM
Posts: 844
|
Or you can get decals just in case you want to go the easy route: http://www.pfyc.com/pc/CA1012/CADECA....html#moreinfo
|
05-02-2012, 10:54 AM | #9 |
Psssssssssshhhhhhhhhhhhh!
Drives: under contruction Join Date: Nov 2009
Location: Marysville, Ohio
Posts: 12,996
|
I got mine from Lupe. (overhaulengines on these forums).
Here is one of his threads. http://www.camaro5.com/forums/showthread.php?t=151002 |
05-02-2012, 11:45 PM | #10 |
Two Miles An Hour
Drives: SIM 2LT RS Join Date: May 2010
Location: chicago
Posts: 1,209
|
i wouldn't use decals. I have and wouldn't do it again. After a while parts starts to peel or tear off because parts of the letters are narrow, glue comes up etc.
__________________
expect nothing, but take everything |
|
|
|
|