Pyr0b0y's SS Build Thread [COTW 5/23/11] - Page 29 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

Redemption · 10-27-2011, 09:07 PM

Didnt get any shots of the rearend or injectors, didn't see em around. Crew is scrambling for sema!!

This system looks amazing! Well made!

Keep me in the loop for startup day, I'll head over!

J

Sent from my payphone using carrier pigeons.

pyr0b0y · 11-07-2011, 11:55 AM

Pfadt Rear Subframe and Diff bushings are installed now. DSS 1-piece driveshaft and 1400hp axels are getting installed today. The new fuel rails are also going on and the Aeromotive Fuel Pump and controller need to be installed along with the return line. After that its off to get tuned!

Revo1 · 11-07-2011, 03:29 PM

PfadtRacing · 11-07-2011, 03:41 PM

Nice update! Get it tuned and let 'er rip! Your car looks like a whole lot of fun.

pyr0b0y · 11-07-2011, 04:13 PM

Should be getting it back Saturday night, but it'll be rev limited to 4k rpms because of engine break in

Quote:

Originally Posted by patriknevan

I am reminded that there are still true craftsmen out there! Great work Luke and Conrad!

Look forward to seeing everything all wrapped up!

Thanks; the shop does outstanding work and goes above and beyond to make sure the car is in perfect condition.

Quote:

Originally Posted by PfadtRacing

Nice update! Get it tuned and let 'er rip! Your car looks like a whole lot of fun.

Liking those bushings a lot! cant wait to test them out when I make it out to the track in a couple weeks. I'll def get some under car video to post.

I'm working on a write up on the install; which didn't take nearly as long as it expected!

Quote:

Originally Posted by Revo1

Maybe 1 more box of popcorn and the car will be good to to!

speedster · 11-07-2011, 05:28 PM

Quote:

Originally Posted by pyr0b0y

Should be getting it back Saturday night, but it'll be rev limited to 4k rpms because of engine break in

Awesome !!

Can't wait to hear your feedback. Bet you have permagrin !!

pyr0b0y · 11-07-2011, 05:51 PM

Quote:

Originally Posted by speedster

Awesome !!

Can't wait to hear your feedback. Bet you have permagrin !!

Hell YES! Get to drive it this weekend for a bit then goes back in for more tuning on 91; then back in again for a c-16 gas tune....then the fun comes.

pyr0b0y · 11-08-2011, 11:54 AM

Stopped by the shop last night; snapped some pics of the rear end. All bushings and axels are installed now. The new Aeromotive Stealth Fuel Pump was installed as well. Driveshaft arrived and is probably getting installed as we speak. Fuel Rails and injectors are going on today and the only thing left is wiring. Luke said we should be able to possibly start the car tonight!!

pyr0b0y · 11-10-2011, 11:40 AM

IT STARTED!!!!!! thats right! after over 3 months of being in the shop my car started and sounded wicked! The entire fuel system in now installed and is getting wired up this morning. The car doesnt have mufflers or a x-pipe for the time being because I'm not sure what i'm doing yet.

We decided to run an Aeromotive regulator and get new fuel rail setup so we can be sure fuel is being distributed evenly to each fuel rail. Gauges are being installed today with dual PLX gauges.

The car will be sent to the tuner today for a couple days and then I get to break it in for a few days before it goes back for a more aggressive tune. I'm getting some videos uploaded right now of the first start up.

pyr0b0y · 11-10-2011, 12:07 PM

Video of startup:

2SSRS@Gen5diy · 11-10-2011, 12:51 PM

Congrats long time coming.

antnicSS2010 · 11-10-2011, 01:33 PM

That's so bad a$$ !!!!

Redemption · 11-10-2011, 01:33 PM

Bad ass. Dibs on a ride in the Beasst!!

J

Sent from my payphone using carrier pigeons.

Riddikulus5Gen · 11-10-2011, 01:54 PM

HELL TO THE YEA!!!! FINALLY!!!!
Love the crazy smoke in the vids, lol

View Poll Results: T Tops or Carbon Fiber?
T Tops	14	73.68%
Carbon Fiber Conversion (Fenders, doors, etc)	5	26.32%
Voters: 19. You may not vote on this poll

10-27-2011, 09:07 PM	#393
Redemption Just Because! Drives: 2010 SIM 2SSRS Join Date: Jun 2010 Location: San Jose, Ca Posts: 6,909	Didnt get any shots of the rearend or injectors, didn't see em around. Crew is scrambling for sema!! This system looks amazing! Well made! Keep me in the loop for startup day, I'll head over! J Sent from my payphone using carrier pigeons. __________________ My Build Thread

11-07-2011, 11:55 AM	#394
pyr0b0y need....more....hp Drives: The Neighbor Hater Join Date: Dec 2010 Location: San Mateo, CA Posts: 4,091	Pfadt Rear Subframe and Diff bushings are installed now. DSS 1-piece driveshaft and 1400hp axels are getting installed today. The new fuel rails are also going on and the Aeromotive Fuel Pump and controller need to be installed along with the return line. After that its off to get tuned! Attached Images __________________ BUILD THREAD BUILT AND MAINTAINED BY BLU808 Mast Motorsports Built LS3 Stroker 418, IPS GT35R Twin Turbos, Exedy GTO4XD Twin Disc Clutch, Aeromotive A1000 Eliminator Stealth Fuel Pump, AEM Meth Injection, DSS 1400hp Axels, BC Coilovers, Pfadt & BMR Suspension, Hawk HPS Pads, Drilled/Slotted Rotors, Hurst Shifter, Custom Roll Cage by Blu808, T3 Ports, 22" Custom Concave Mesh Rims

11-07-2011, 03:29 PM	#395
Revo1 Don't Like it? Suggit. Drives: 2010 2SS/RS Join Date: Aug 2008 Location: Fresno, CA Posts: 14,832 View My Garage	__________________ "Tops off, tach up baby- loud and proud!" A Camaro lover from day one- 1996 3.8 V6 Camaro, to 1996 5.7 LT1 Camaro Z28, to the sold 2002 5.7 LS1 Camaro SS, and NOW, a [I]6.2 L99 VR 2SS/RS: XS Power stainless full exhaust, Airaid CAI, BMR drop springs and sways, custom tune by Cal Speed- 411rwhp

11-08-2011, 11:54 AM	#400
pyr0b0y need....more....hp Drives: The Neighbor Hater Join Date: Dec 2010 Location: San Mateo, CA Posts: 4,091	Stopped by the shop last night; snapped some pics of the rear end. All bushings and axels are installed now. The new Aeromotive Stealth Fuel Pump was installed as well. Driveshaft arrived and is probably getting installed as we speak. Fuel Rails and injectors are going on today and the only thing left is wiring. Luke said we should be able to possibly start the car tonight!! __________________ BUILD THREAD BUILT AND MAINTAINED BY BLU808 Mast Motorsports Built LS3 Stroker 418, IPS GT35R Twin Turbos, Exedy GTO4XD Twin Disc Clutch, Aeromotive A1000 Eliminator Stealth Fuel Pump, AEM Meth Injection, DSS 1400hp Axels, BC Coilovers, Pfadt & BMR Suspension, Hawk HPS Pads, Drilled/Slotted Rotors, Hurst Shifter, Custom Roll Cage by Blu808, T3 Ports, 22" Custom Concave Mesh Rims

11-07-2011, 03:41 PM	#396
PfadtRacing Drives: 2010 Camaro, 2006 Z06 Join Date: Feb 2009 Location: SLC, UT Posts: 3,370	Nice update! Get it tuned and let 'er rip! Your car looks like a whole lot of fun.

11-10-2011, 11:40 AM	#401
pyr0b0y need....more....hp Drives: The Neighbor Hater Join Date: Dec 2010 Location: San Mateo, CA Posts: 4,091	IT STARTED!!!!!! thats right! after over 3 months of being in the shop my car started and sounded wicked! The entire fuel system in now installed and is getting wired up this morning. The car doesnt have mufflers or a x-pipe for the time being because I'm not sure what i'm doing yet. We decided to run an Aeromotive regulator and get new fuel rail setup so we can be sure fuel is being distributed evenly to each fuel rail. Gauges are being installed today with dual PLX gauges. The car will be sent to the tuner today for a couple days and then I get to break it in for a few days before it goes back for a more aggressive tune. I'm getting some videos uploaded right now of the first start up. __________________ BUILD THREAD BUILT AND MAINTAINED BY BLU808 Mast Motorsports Built LS3 Stroker 418, IPS GT35R Twin Turbos, Exedy GTO4XD Twin Disc Clutch, Aeromotive A1000 Eliminator Stealth Fuel Pump, AEM Meth Injection, DSS 1400hp Axels, BC Coilovers, Pfadt & BMR Suspension, Hawk HPS Pads, Drilled/Slotted Rotors, Hurst Shifter, Custom Roll Cage by Blu808, T3 Ports, 22" Custom Concave Mesh Rims

11-10-2011, 12:07 PM	#402
pyr0b0y need....more....hp Drives: The Neighbor Hater Join Date: Dec 2010 Location: San Mateo, CA Posts: 4,091	Video of startup: __________________ BUILD THREAD BUILT AND MAINTAINED BY BLU808 Mast Motorsports Built LS3 Stroker 418, IPS GT35R Twin Turbos, Exedy GTO4XD Twin Disc Clutch, Aeromotive A1000 Eliminator Stealth Fuel Pump, AEM Meth Injection, DSS 1400hp Axels, BC Coilovers, Pfadt & BMR Suspension, Hawk HPS Pads, Drilled/Slotted Rotors, Hurst Shifter, Custom Roll Cage by Blu808, T3 Ports, 22" Custom Concave Mesh Rims

11-10-2011, 12:51 PM	#403
2SSRS@Gen5diy Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008 Location: By the lake in AZ Posts: 15,719 View My Garage	Congrats long time coming.

11-10-2011, 01:33 PM	#404
antnicSS2010 #145 Drives: 2014 White ZL1 Join Date: Jul 2010 Location: South San Francisco, CA Posts: 366	That's so bad a$$ !!!! __________________

11-10-2011, 01:33 PM	#405
Redemption Just Because! Drives: 2010 SIM 2SSRS Join Date: Jun 2010 Location: San Jose, Ca Posts: 6,909	Bad ass. Dibs on a ride in the Beasst!! J Sent from my payphone using carrier pigeons. __________________ My Build Thread

11-10-2011, 01:54 PM	#406
Riddikulus5Gen Drives: 2010 ABM RS 2LT Join Date: Nov 2010 Location: San Jose, CA / Bay Area Posts: 411 View My Garage	HELL TO THE YEA!!!! FINALLY!!!! Love the crazy smoke in the vids, lol __________________ I GOT MY CAMARO FOR MY SIG.!!!! AT LAST!!! Built: October 2010 / ABM Chevy Camaro RS 2LT Grey/Ebony Leather Interior / 6-Speed Manual Trans. Gauge Cluster / Silver Rally Stripes (May remove?) 20" Polished Aluminum Rims. K&N Cold-Air Intake / Corsa Exhaust.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
3rd Gen Camaro Street Stock build thread (dialup beware)	zlathim	3rd Generation Camaros	9	12-06-2018 10:30 AM
Tom Henry Racing THR22 2010/LS3/IBM/Supercharged SS Camaro [COTW 10/29/12]	GTAHVIT	Member Car Journals	5217	06-27-2016 08:14 AM
Do you want the Z28?	ChrisB	Camaro ZL1 Forum - ZL1 Specific Topics	1616	09-04-2010 11:49 PM
Anyone in St. Louis want a black SS March build Camaro	Sean_W	Camaro Price \| Ordering \| Tracking \| Dealers Discussions	11	03-08-2009 01:31 PM