You are browsing camaro5 
 |
|
10-11-2012, 12:50 PM
|
#1 |
Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008
Location: By the lake in AZ
Posts: 15,719
|
1969 looking tail lights All LED.
Working with a member on here with making a 1 pc 69 LED tail light. here is the first picks of the circuit board with LED's on, and only the ones for the runing are on in the next pic.
|
|
|
|
10-11-2012, 01:31 PM
|
#2 |
     
Drives: Black 2011 Camaro LS Join Date: Feb 2011
Location: Texas
Posts: 1,694
|
So will these fit similar to the TA conversion tail lights? By combining both tail light bays (per side) into one?
__________________
White Fender Hashes from Big Worm Graphix with Custom White Bowties
GM Factory Remote Start and Factory Key Fob SS Fascia, Factory RS HIDs, Plasma P13W fog lights Non-RS to RS and fog light harness by Gen5DIY LED Interior, Trunk, and Licence Plate lights in white ZL1 Spoiler with Gen5DIY harness Factory NPP cat back Blacked out tail light bezels Factory 20 inch wheels wrapped in Nitto Motivos Lowered 1.25inch on Eibach Pro springs |
|
|
|
|
10-11-2012, 02:44 PM
|
#3 |
|
Drives: 2016 1LT RS Camaro; 72 Chevelle Join Date: Apr 2008
Location: Central Point, OR
Posts: 5,688
  |
Will be interesting to see what they look like installed on the car.
|
|
|
|
|
10-11-2012, 02:54 PM
|
#4 | ||
|
Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008
Location: By the lake in AZ
Posts: 15,719
|
Quote:
Quote:
|
||
|
|
|
|
10-11-2012, 06:00 PM
|
#5 |
 
Drives: 2ss camaro 2010 Join Date: Jan 2011
Location: brownsville texas
Posts: 235
|
looks bad a$$ great job ofer.
|
|
|
|
|
10-11-2012, 06:03 PM
|
#6 |
Drives: 2010, 2LT, RS, 6M, ABM (#1893) SOLD Join Date: Mar 2011
Location: Willits, CA
Posts: 1,437
|
nice
__________________
2010 2LT/RS; 6M, ABM, Torq Thrust M w/custom center caps, Solo MachX-LLT, Blue Anodized Pedals, Barton Shifter w/UMI blue anodized pistol grip, Ported IM from Mace, 25mm isolator/spacer from Mace, Vararam CAI, Euro Rear Fascia, RX Breather Cap. SOLD 4/23/13.
Now have a 1965 Chevelle 4 dr wagon!! |
|
|
|
|
10-18-2012, 09:52 PM
|
#7 |
|
Drives: 2ss camaro 2010 Join Date: Jan 2011
Location: brownsville texas
Posts: 235
|
OK guys here are some pic of the tailight Offer and I are working on. this is one taillight 90% complete what do you all think !!!!!!!!!!
|
|
|
|
|
10-18-2012, 09:54 PM
|
#8 |
   
Drives: 2012 2SS/RS Convertible Join Date: Aug 2012
Location: SoCal Baby...
Posts: 2,530
|
hmmm
__________________
I'm only responsible for what I say, not for what you fail to understand.
|
|
|
|
|
10-18-2012, 11:40 PM
|
#9 |
Drives: 2010 Camaro 2SS RS Join Date: Nov 2011
Location: NYC
Posts: 2,387
|
def need to see both on a car before i can give a good opinion... either way, looks like great clean work! even on the bezel
did you consider taking the bezel and sectioning it off into 3 like the 69? or even with the single horizontal bar through the middle from left to right? I think that would look best edit: sorta like this 
__________________
 |
|
|
|
|
10-19-2012, 12:50 AM
|
#10 |
|
Drives: 2ss camaro 2010 Join Date: Jan 2011
Location: brownsville texas
Posts: 235
|
how about this this is tape but , i am going to modify the bezel like this .
|
|
|
|
|
10-19-2012, 12:55 AM
|
#11 |
|
Drives: 2010 Camaro 2SS RS Join Date: Nov 2011
Location: NYC
Posts: 2,387
|
^^^ pretty cool... looks better IMO... But I would do one or the other, not both
Id probably lean towards the single horizontal strip, being that it would be easier to center it with the LEDs... with the vertical ones, it looks like some bulbs would be partially blocked due to the led arrangement
__________________
|
|
|
|
|
10-19-2012, 01:08 AM
|
#12 |
|
Drives: 2ss camaro 2010 Join Date: Jan 2011
Location: brownsville texas
Posts: 235
|
the vertical one will line up pefect just have the led board thats inside are for the passenger side thats why they dont match right now but they will like this pic
|
|
|
|
|
10-19-2012, 01:09 AM
|
#13 |
|
Account Suspended
Drives: nothing Join Date: Nov 2010
Location: a hole
Posts: 17,906
|
This seems too cool to be real. Will the new bezels cover where we would be cutting the bars out of the rear bumper facia? Or would a bodyshop need to sculpture it to fit?
|
|
|
|
|
10-19-2012, 01:14 AM
|
#14 |
|
Drives: 2ss camaro 2010 Join Date: Jan 2011
Location: brownsville texas
Posts: 235
|
you can see on post 7 picture #1 the size of the patch ,there wile be a small section to repair after you cut out the section in the middle but any good body shop can handle it
|
|
|
|
|
|
|
|
 |
|
|
