11-04-2013, 03:22 PM | #1 |
Drives: 2011RedJewel, FI Join Date: Dec 2011
Location: San Antonio,TX
Posts: 816
|
ADM fpcm
Just wondering where the Fuel pressure control module is?
I looking to use the ADM fpcm and want to make sure I can do bit myself. Thanks! |
11-04-2013, 03:48 PM | #2 |
Drives: 2010 2SS LS3, 2013 duramax Join Date: Nov 2012
Location: Dover, De
Posts: 1,451
|
Behind the plastic trim next to rear seat. Take seat out, pop off trim and its a plug and like 1 10mm nut. Not hard, takes 20 min
__________________
ECS Ysi-B, cam, Tsp 2" longtubes, Squash dual pumps, Id1300s, meth, 4L80e, FTI 3600, ZL1 3.73 diff, BMR suspension, 15" conversion, weld rts mt 275 et street R. 9.6@147mph
|
11-04-2013, 03:53 PM | #3 |
Drives: BLUE CAMARO ZL1 1LE M6 Join Date: Jun 2009
Location: ON THE DYNO WATERBURY CT.
Posts: 15,225
|
Behind Rear, Passenger, interior Panel, under the window.
__________________
www.jannettyracing.com
Celebrating 37 years Performance parts, Installation, Fabrication, Dyno tuning, Remote custom tuning, and alignments. 203-753-7223 Waterbury CT. 06705 email tedj@jannettyracing.com |
11-04-2013, 03:55 PM | #4 |
Drives: 2011RedJewel, FI Join Date: Dec 2011
Location: San Antonio,TX
Posts: 816
|
Thanks guys!
|
11-04-2013, 07:40 PM | #5 |
|
Here you go
Best link I found, it's for installing speakers, but got the job done. Took about 20 min by myself. http://www.camaro5.com/forums/showthread.php?t=123352
__________________
2017 ZL1 A10: 8.84 @ 156 PB
2017 ZL1 A10: Previously FBO 756/761 (9.6 @ 143 1/4) SOLD-2013 ZL1 M6:BTR,LTs,IDs,ATI,RotoFab10.84@129 SOLD-2011 SS M6: Blower, Cam, Alky, LTs. |
11-04-2013, 08:11 PM | #6 |
Drives: 2011RedJewel, FI Join Date: Dec 2011
Location: San Antonio,TX
Posts: 816
|
Awesome! Thanks!
|
11-06-2013, 05:43 PM | #7 |
Can anyone confirm location on a convertible? I was told by someone it is behind the rear seat between the seat back and the trunk.
|
|
11-06-2013, 07:52 PM | #8 |
Drives: 2011 2SS Convertible Supercharged Join Date: Nov 2010
Location: WI Cert Welder Navy NSSN
Posts: 1,157
|
|
11-06-2013, 08:09 PM | #9 |
Drives: 2011RedJewel, FI Join Date: Dec 2011
Location: San Antonio,TX
Posts: 816
|
Putting on that fpcm require any tuning or just plug and go?
|
11-06-2013, 08:14 PM | #10 |
Drives: 2011 2SS Convertible Supercharged Join Date: Nov 2010
Location: WI Cert Welder Navy NSSN
Posts: 1,157
|
|
11-06-2013, 08:27 PM | #11 |
|
Yup installed mine, then I took it to the tuner. You need to get it tuned to get the benefits. But yes you can plug and play but nothing will change until the tune.
__________________
2017 ZL1 A10: 8.84 @ 156 PB
2017 ZL1 A10: Previously FBO 756/761 (9.6 @ 143 1/4) SOLD-2013 ZL1 M6:BTR,LTs,IDs,ATI,RotoFab10.84@129 SOLD-2011 SS M6: Blower, Cam, Alky, LTs. |
11-06-2013, 08:40 PM | #12 |
Drives: 2011RedJewel, FI Join Date: Dec 2011
Location: San Antonio,TX
Posts: 816
|
Thanks Ron. That's what I thought.
|
11-07-2013, 05:20 AM | #13 |
05-09-2014, 09:49 AM | #14 |
Drives: 2014 camaro 1lt Join Date: Sep 2013
Location: florida
Posts: 9
|
on the 2013 zl1 convertible its on pass side ,along side top part of rear seat ,just pop the two upper clips and fold rear seat down .
__________________
|
|
|
|
|