01-26-2015, 01:46 PM | #1 |
NCTiger 2012 1SS
I have been a community observer for years and the forum has provided a lot of information from which I could pull ideas, lessons learned, and DIY how-to's. I bought my 2012 1SS non-RS in July of 2012 and it is the first car I purchased myself. From the beginning I had a mod list for the car. It took about ten months before I purchased my first mods and it went from there. I finally got around to making my build thread. I hope it brings some interest.
Base Car: 2012 Camaro 1SS Non-RS. Summit White. Black interior. Satin Black Rally Stripes Performance Mods:
Last edited by NCTiger; 02-18-2015 at 04:43 PM. |
|
01-26-2015, 01:51 PM | #2 |
CAI & Cat-Back Exhaust
The first two mods were a K&N CAI and Corsa Cat-back exhaust. Installed while I was living in Richmond, VA.
Corsa Installation - It was a cold weather installation, so there are few photos. Old Exhaust: New Exhaust: Last edited by NCTiger; 02-11-2015 at 10:42 AM. |
|
01-26-2015, 01:58 PM | #3 |
Hotckis Track Pack Stage 2
The first serious installation was the Hotchkis Track Pack that lowered the vehicle and added the chassis brace. It was immediately noticeable that the vehicle hooked up better and that speed bumps & pot holes were now my worst enemy.
Pre-Install During Install: After Install: Last edited by NCTiger; 02-11-2015 at 10:45 AM. |
|
01-26-2015, 02:09 PM | #4 |
Headlight/Fog Light Conversion
I opted for not getting the RS package because I did not see the Halo headlights and HIDs being worth the $3k. I always had plans to switch out the halogen lamps, so I opted for the Eagle Eye headlight and when I was doing it I included an HID conversion. This was the first time I had taken off a major body panel, so it was a little anxiety-inducing. I think it all turned out well. The support of Diode Dynamics with the wiring diagrams was paramount and the many DIY's on the forum for removing the front bumper assisted greatly.
Pre-Installation: Eagle Eye Headlamp: HID & Switchback LED Conversion: During Installation: Complete: Last edited by NCTiger; 02-11-2015 at 10:49 AM. |
|
01-26-2015, 02:24 PM | #5 |
Havoc Diffuser
One of the first body mods that I knew I wanted was the Havoc Diffuser. It is a perfect example, to me, of an improvement upon the existing diffuser. It keeps the same lines of the OEM, but makes the rear very unique. I know some people have had issues with fitment. So far, mine installed in 3 hours and fit within my expectations of aftermarket.
Parts Received: During Paint: During Install: Finished: Last edited by NCTiger; 02-11-2015 at 10:54 AM. |
|
01-26-2015, 02:35 PM | #6 |
Aural Assault Vehicle
Drives: 2010 IBM 2SS/RS, 2015 Sierra Denali Join Date: Jun 2011
Location: Garner, NC
Posts: 792
|
Nice! What are your plans for future mods?
__________________
My amplifier pop/click/thump solution thread
Power Mods * K&N Typhoon CAI, Flowmaster American Thunder cat-back exhaust, Hurst Short Throw Shifter Exterior Mods * Black Phantom Grille * 22" T.I.S. 537MS wheels w/ Nitto INVO rubber * OEM body kit Suspension Mods * BC Racing Coilovers * Lakewood Strut Tower Brace Audio Mods * Stinger SPP 2250 Battery * Mosconi 6to8v8 w/ RCD * Pioneer AVH-X7500BT * Scosche Dash Kit * 2 - Mosconi AS200.4 * 2 - JL Audio 13W6v2 * Focal 165KRX2 Power (active) * Mosconi Gladen One 240.2 * Rockford Fosgate Power T1692 |
01-26-2015, 07:15 PM | #7 |
02-05-2015, 06:52 PM | #8 |
ACS T4 Splitter and Rockers
Well, the parts arrived a full week ago but I have been too busy to get them installed. Doing some test fitting, they are going to do just fine. Great packing for painted parts resulted in no scratches and I couldn't be happier.
It will be another week before I can get them installed. The anticipation is killing me. Last edited by NCTiger; 02-11-2015 at 10:56 AM. |
|
02-05-2015, 07:17 PM | #9 |
|
Nice eagle eyes!!!!
__________________
SLP Loud Mouth 1 Exhaust, K&N CAI, RS Headlights, NightOwl V2 halo kit, ZL1 Grille, Custom 2LS Emblems, Green Footwells, GM GFX splitter, Ace Alloy Convex All Matte Black Wheels(20x9 & 20x10.5) wrapped in Toyo Proxe STII(255/45/20 & 295/40/20)
|
02-06-2015, 11:40 AM | #10 |
SoCal HT5 COTW 4/21/13
Drives: 2011 SS/RS Blown & Cammed LS3 Join Date: Sep 2011
Location: Sandy Eggo
Posts: 3,047
|
Great build thread. Keep up the good work. keep the pics and mods coming
|
02-07-2015, 06:27 PM | #11 |
Drives: 2012 Victory Red 1SS/RS Join Date: Apr 2012
Location: Meridianville, AL
Posts: 254
|
I'm liking those ACS parts! Good choice!
|
02-18-2015, 10:54 AM | #12 |
Splitter and Rocker Install
I took some time this weekend to get the splitter and rockers installed. I think they look great. The instructions were relatively clear. I purchased the undertray with the splitter and it came as one piece. This seemed like a good thing until I started to mount the splitter. Getting the bolts lined up required extreme dexterity and patience. Luckily the rockers were very straight forward and easily installed.
Last edited by NCTiger; 02-19-2015 at 08:52 PM. |
|
|
|
|
|