You are browsing camaro5 
 |
|
01-17-2019, 04:29 PM
|
#1 |
       
|
Dog box
So I have my old 6060 sitting here taking up space. Any one in here swap the guts to make it a dog box?
Would be a nice back up incase my th400 goes out.
__________________
MODS 6.0 forged iron block, TH400, B&M shifter, DSS axles & driveshaft, Viking / BMR suspension, Full custom fuel system with cell, Twin 76mm teriyaki tornados on 24lbs.
 https://www.instagram.com/whoopa_ss/ |
|
|
|
01-18-2019, 08:42 AM
|
#2 |
Drives: 2010 Camaro 2SS/RS M6 Join Date: May 2009
Location: Idaho
Posts: 726
|
Please forgive my ignorance. What is a dog box?
__________________
GPI SS2; EE E2 catch can; SP 1 7/8" LT Headers w/ hfc; FM AT 3" cat-back; CAI Cold Air Intake; AEM Wideband
Tuned by GPI McCleod RXT; MGW flat stick; Ram Clutch slave cylinder & hydraulic adjuster BMR cradle & diff bushings, trailing arms, toe rods & upper control arm bushings Hotchkis sub-frame brace Stop Tech Z-23 brakes 4.10 gears, Eaton Truetrac, LPW diff cover Best 1/4 mile 12.073 @ 115.68 mph 3,300 ft DA |
|
|
|
|
01-18-2019, 08:58 AM
|
#3 |
|
Account Suspended
Drives: 2013 Sparkly Red One Join Date: Dec 2018
Location: Hospitality State
Posts: 2,558
|
What is a dog box transmission?
Note that the gears are of the helical variety. This is a dogbox transmission. Note that the gears are straight cut. To shift in a synchromesh transmission, you engage the clutch, and as you shift, the synchros match shaft speed to the shaft with the gear you're about to engage to the output shaft speed. |
|
|
|
|
01-18-2019, 09:18 AM
|
#4 | ||
|
Quote:
Quote:
Lots of info out there to explain the difference better than I can.
__________________
468, Mishimoto rad + oil cooler, TSP LTH
MCS 2WNR CTSV/ZL1 front calipers/rotors + G-Loc Forgestar CF-5 19x11 |
||
|
|
|
|
01-18-2019, 09:45 AM
|
#5 |
|
Account Suspended
Drives: 2013 Sparkly Red One Join Date: Dec 2018
Location: Hospitality State
Posts: 2,558
|
M22 Rock Crusher.
|
|
|
|
|
01-18-2019, 11:09 AM
|
#6 | |
|
Drives: 2010 Camaro 2SS/RS M6 Join Date: May 2009
Location: Idaho
Posts: 726
|
Quote:
__________________
GPI SS2; EE E2 catch can; SP 1 7/8" LT Headers w/ hfc; FM AT 3" cat-back; CAI Cold Air Intake; AEM Wideband
Tuned by GPI McCleod RXT; MGW flat stick; Ram Clutch slave cylinder & hydraulic adjuster BMR cradle & diff bushings, trailing arms, toe rods & upper control arm bushings Hotchkis sub-frame brace Stop Tech Z-23 brakes 4.10 gears, Eaton Truetrac, LPW diff cover Best 1/4 mile 12.073 @ 115.68 mph 3,300 ft DA |
|
|
|
|
|
|
|
|
 |
|
|
