11-29-2012, 08:03 PM | #1 |
Drives: '02 Trailblazer, '12 Camaro 2SS/RS Join Date: Jun 2012
Location: AK
Posts: 819
|
Stupid question....SAE or Metric
So I am going to get an impact wrench. Nothing too fancy, but something. I will use it mostly for wheel changes in winter and summer. However, i will be doing some suspension mods, and if I get more confident who knows what other mods down the road.
Do I need impact sockets or can I use my regular Craftsman ones? If I get impact specific, am I better off getting impact sockets in Standard sizes or metric? Buy a set or just get them piece by piece? They are not cheep and this tool likely will not be used all that often so if I can cost down that would be ideal. |
11-29-2012, 08:31 PM | #2 |
KNGTFALL
Drives: 2012 2SS 45th edition Join Date: Aug 2012
Location: (Near) Charlotte, NC
Posts: 1,533
|
First, you can use the impact for removing wheels, but you should use a good torque wrench for re installing the wheels.
Now with that aside...... Regular sockets can shatter when used with a impact wrench, seen it, done it.. Most cars nowadays will have both SAE and Metric fasteners on them. So far on my Camaro I have only run into metric fasteners. So if you are going to use this on the Camaro only I would start with Metric sockets. |
11-29-2012, 09:43 PM | #3 |
knows 2 facts about ducks
Drives: ...and they're both wrong Join Date: Aug 2009
Location: The HMS Invincible
Posts: 25,072
|
Are camaros are metric. Got to remember that they're built in Canada eh
|
11-29-2012, 09:58 PM | #4 |
|
Good thing all of my tools were standard lol
__________________
My Build Thread
http://camaro5.com/forums/showthread...=1#post5036900 Maureen@Rodgers Chevrolet...The best prices and customer service period!!(734)676-9600 Gen5Diy.com.....http://www.gen5diy.com/ Wretched Motorsports..www.wretchedms.com/ Pedders USA...http://www.peddersusa.com/ |
11-30-2012, 08:16 AM | #5 | |
Get real!
Quote:
I have used a impacts many years and never strip or over torque nuts or studs. It's all in the users hands and common since will get the job done safely. Impacts can over torque lug nut's and studs but not likely unless you really have a high torque gun running 120 pounds and you set there and continually stay on it. I seriouly doubt you could do it with the average low budget impact or home compressor. Just tighten in a crisscross patern and don't bring them up to torque the first time, repeat. I say impact away! If you strip one you will know and feel the limitations of your gun and the turning element. Definitely use impact sockets, you will ruin standard sockets in a short time. Never hold your hand around a socket when impacting. If it breaks it will seriously rip the shit out of you hand in a hot split second. Even impact sockets.
__________________
2010 L99 Black on Black W/Ground effects
Mods: Kenne Bell, LS3 Conversion, LS9 cam, BMR Stage 2 |
||
11-30-2012, 07:46 PM | #6 |
KNGTFALL
Drives: 2012 2SS 45th edition Join Date: Aug 2012
Location: (Near) Charlotte, NC
Posts: 1,533
|
Yeah its tough to strip a 14mm stud. But f'ing up your rims by over tightening is more of an issue..
|
12-01-2012, 03:54 AM | #7 |
Drives: '02 Trailblazer, '12 Camaro 2SS/RS Join Date: Jun 2012
Location: AK
Posts: 819
|
I have torque wrench for final torque down. Just looking for something quick to break and remove the lugs. Maybe zip them on the stud to the wheel them manually torque them from there.
|
12-01-2012, 04:16 PM | #8 |
|
If you rip up your hand with a impact gun, refusing to release the trigger. Then its time to give up. I hope you do not operate a hytorque wrench or a one inch impac they tend to do severe damage.
|
|
|
|
|