09-13-2012, 02:39 PM | #1 |
Drives: 2008Corvette Join Date: Feb 2012
Location: Ga
Posts: 691
|
PICS-2011 GM ZR1 Wheels on 2011 CamaroSS
I know this is the FI Section, however I have to share this with all of you! With the new Camaro5 I have always wondered about aftermarket wheels and what is the WIDEST wheel and tire combo you could fit. Not sure if anyone has tried before, however here is a few pics of my 2011 GM ZR1 Wheels fitted up nicely on our 2011 SS Camaro. The ONLY modification to the rear is a 1/4 in wheel spacer. That is it! With the low profile of the tires the Camaro needs to be lowered a little more, however this camaro looks badazz with this wheel/tire combo! Wheel Specs are: REAR-GM 2011 ZR1 Wheels -20x12 in rear with 335-25-20 Michelin Pilot Sport Tires FRONT-GM 2011 ZR1 Wheels-19x10.5in front with 285-30-19 Michelin Pilot Sport Tires Pics Driver Side View DriverSide View from Rear-13in. of Tire out back is BADAZZ!! Passenger tire view from rear. Not so badazz anymore. Driverside rear fender view from top looking down on tire. Tucks nicely! Rear Tire widths compared side by side
|
09-13-2012, 02:46 PM | #2 |
Account Suspended
|
Was the spacer needed for control arm clearance or brake clearance?
I wouldn't be caught dead with a spacer on my car, especially on the drive axle. |
09-13-2012, 03:03 PM | #3 | |
Drives: 2008Corvette Join Date: Feb 2012
Location: Ga
Posts: 691
|
Quote:
It was needed to move the wheel outward from the plastic fender panel. The wheel and tires clear the lower control arms and the brakes just fine. The 10.5in wide wheel fit the rear fine without any spacer, however I wanted the 13in wide tire on back.The spacer will cause absolutely no harm to anything. Chris |
|
09-13-2012, 03:11 PM | #4 |
Drives: 2008Corvette Join Date: Feb 2012
Location: Ga
Posts: 691
|
A few more pics of the stance.
Chris |
09-13-2012, 03:13 PM | #5 |
Drives: 2011 SS Join Date: Nov 2011
Location: new jersey
Posts: 379
|
So wait if a 13 in tire fits...wouldnt a properly sized 12 in rim also work. ? I have a 315/20 on my car and it appears to be maxed out....conti extreme by the way.
Also I went on tire rack and saw a 345/25/20 could this also fit Chris? PS @ 600 a pop ..thats freakin costly ...sheesh |
09-13-2012, 03:41 PM | #6 | |
Drives: 2008Corvette Join Date: Feb 2012
Location: Ga
Posts: 691
|
Quote:
I will do a little more research and get the exact specs of these wheels. Chris |
|
09-13-2012, 04:42 PM | #7 |
|
i run 315's with a 10.87 stock wheel widened and powder coated on mine with a spacer on the rear.
|
09-13-2012, 05:26 PM | #8 |
by Odeon
Drives: '12 SS/RS A6 IOM SOLD, '13 1LE IOM Join Date: Nov 2011
Location: Good question
Posts: 1,707
|
Happen to know the $$$ of these babies?
__________________
"It works 60% of the time, every time."
"Some say it's a waste of time, others say it's an incredible waste of time." "The ultimate measure of a man is not where he stands in moments of comfort and convenience, but where he stands at times of challenge and controversy." 2013 IOM SS/RS - 1LE. Born 5/6/2013 (1 of 32 1SS IOM 1LE's) |
09-13-2012, 05:45 PM | #9 |
very nice
__________________
LS3 M6 w/ Turbonetics stage 1 turbo kit
Huron Speed twin 64's waiting to be installed |
|
09-13-2012, 05:49 PM | #10 |
need....more....hp
Drives: The Neighbor Hater Join Date: Dec 2010
Location: San Mateo, CA
Posts: 4,091
|
Someone did it! Wish you would have posted this last year!! ha i really wanted a ZR1 set on my car and everyone said it couldn't be done! The car looks AWEEEESOME!
__________________
Mast Motorsports Built LS3 Stroker 418, IPS GT35R Twin Turbos, Exedy GTO4XD Twin Disc Clutch, Aeromotive A1000 Eliminator Stealth Fuel Pump, AEM Meth Injection, DSS 1400hp Axels, BC Coilovers, Pfadt & BMR Suspension, Hawk HPS Pads, Drilled/Slotted Rotors, Hurst Shifter, Custom Roll Cage by Blu808, T3 Ports, 22" Custom Concave Mesh Rims |
09-13-2012, 06:42 PM | #11 |
Drives: 2010 TT Camaro SS Join Date: Mar 2011
Location: Augusta GA
Posts: 268
|
AHHHHHH I see my Camaro in the background...
|
09-13-2012, 06:49 PM | #12 | |
Drives: 2011 SS Join Date: Nov 2011
Location: new jersey
Posts: 379
|
Quote:
See this ish man...I knew it could be done. i just don't have the mullah to blow on trying. But if Chris or anyone gets the total specs to run a tire like a zr1 rear, or viper..i am in...I tell ya those vipers look so sweet just curbside pimpng. |
|
09-14-2012, 02:27 PM | #13 |
Drives: My wife crazy with my C5 usage. Join Date: Apr 2009
Location: DFW
Posts: 6,558
|
That looks awesome! How tall are the tires? The rear looks like it is shorter than the factory tires. Any issues with stabilitrack?
__________________
UNDER CONSTRUCTION......again......
|
09-14-2012, 02:31 PM | #14 |
Recalled user
Drives: '12 Camaro SS, '18 Colorado Z71 Join Date: Mar 2009
Location: Richmond, VA
Posts: 3,419
|
Those wheels are awesome. I've been wanting the same on my car and have even searched to find it being done. No luck until this thread.
__________________
2012 2SS 45th AE LS3 M6 Borla ATAK Catback Kooks Stepped LT Headers CAI Intake Hexvents VMAX CNC Ported Throttle Body RX Catch Can Hurst Short Throw Shifter Pfadt ZL-Spec Stage 3 Suspension Forgestar F14 Tuned by Frost |
|
|
|
|