Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
Cold Air Inductions
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Engine | Drivetrain | Powertrain Technical Discussions > Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons


Reply
 
Thread Tools
Old 06-07-2016, 12:28 PM   #1
alvinmiles
 
alvinmiles's Avatar
 
Drives: 2011 Camaro 2SS - Black
Join Date: Dec 2014
Location: Lexington, KY
Posts: 42
Header install. No check engine light but stabilitrak and traction control

Installed headers. Used tuner for headers, dod delete, rear o2 delete. But now i get lights about stabilitrak, traction control with no cel. Any ideas.
__________________
Posting all mods as i go, along with other non sense.

http://m.youtube.com/channel/UCJY1FzsIqSAtCJxZdYeuz-A
alvinmiles is offline   Reply With Quote
Old 06-07-2016, 12:49 PM   #2
1KillerSS
Too much is never enough!
 
1KillerSS's Avatar
 
Drives: AGP TT SS [COTW] 4/20/15
Join Date: Feb 2014
Location: Toledo,OH
Posts: 4,154
Send a message via Skype™ to 1KillerSS
Quote:
Originally Posted by alvinmiles View Post
Installed headers. Used tuner for headers, dod delete, rear o2 delete. But now i get lights about stabilitrak, traction control with no cel. Any ideas.
Yea your tuner missed the boat, bring it back to him and have him fix it. The service stabilitytrac light can also be caused from too much timing, among other things. Best to send him a datalog.
__________________
AGP TT kit, 54/57 Forged rotating assembly, Custom grind cam... Dual nozzle meth, ID850's, Livernois dual fuel pumps, ECS BAP, 25% UDP, 3 inch Magnaflow catback with X pipe, Mantic 9000 clutch, DSS 1000hp axles, DSS aluminum driveshaft, ZL1 rear end, solid subframe bushings, HE differential offset bushings, BMR Trailing arm, BMR toe rods, Lingenfelter LNC-2000,SJM Line Lock. 747 whp 714wtq


Build thread
http://www.camaro5.com/forums/showth...55#post8107855
1KillerSS is offline   Reply With Quote
Old 06-08-2016, 10:18 AM   #3
MMC

 
MMC's Avatar
 
Drives: CGM 2SS/RS, 1987 & 2014 Silverado
Join Date: Oct 2010
Location: Spencerport, NY
Posts: 1,012
Check the plug wires.
__________________
MMC is offline   Reply With Quote
Old 06-08-2016, 12:41 PM   #4
alvinmiles
 
alvinmiles's Avatar
 
Drives: 2011 Camaro 2SS - Black
Join Date: Dec 2014
Location: Lexington, KY
Posts: 42
Quote:
Originally Posted by MMC View Post
Check the plug wires.
Even without a cel?
__________________
Posting all mods as i go, along with other non sense.

http://m.youtube.com/channel/UCJY1FzsIqSAtCJxZdYeuz-A
alvinmiles is offline   Reply With Quote
Old 06-08-2016, 01:34 PM   #5
keith.wilkinson.10
 
keith.wilkinson.10's Avatar
 
Drives: 2010 2SS/RS IBM
Join Date: Nov 2014
Location: Moncks Corner SC
Posts: 204
Quote:
Originally Posted by MMC View Post
Check the plug wires.
Check em

Sent from my SAMSUNG-SM-G890A using Tapatalk
keith.wilkinson.10 is offline   Reply With Quote
Old 06-08-2016, 04:02 PM   #6
1KillerSS
Too much is never enough!
 
1KillerSS's Avatar
 
Drives: AGP TT SS [COTW] 4/20/15
Join Date: Feb 2014
Location: Toledo,OH
Posts: 4,154
Send a message via Skype™ to 1KillerSS
Quote:
Originally Posted by MMC View Post
Check the plug wires.
+1 should be number 1 thing to do

Quote:
Originally Posted by alvinmiles View Post
Even without a cel?

Yes a miss fire wont always cause a CEL, but will trigger a Stabilitrac message.
__________________
AGP TT kit, 54/57 Forged rotating assembly, Custom grind cam... Dual nozzle meth, ID850's, Livernois dual fuel pumps, ECS BAP, 25% UDP, 3 inch Magnaflow catback with X pipe, Mantic 9000 clutch, DSS 1000hp axles, DSS aluminum driveshaft, ZL1 rear end, solid subframe bushings, HE differential offset bushings, BMR Trailing arm, BMR toe rods, Lingenfelter LNC-2000,SJM Line Lock. 747 whp 714wtq


Build thread
http://www.camaro5.com/forums/showth...55#post8107855
1KillerSS is offline   Reply With Quote
Old 06-08-2016, 05:27 PM   #7
G701LE

 
G701LE's Avatar
 
Drives: 2010 2SS/RS L99 IBM silver stipes
Join Date: Dec 2015
Location: K.C. Kansas
Posts: 1,335
Did you undo the steering shaft when you installed the headers?
__________________
2010 Imperial Blue w/ Silver stripes 2SS/RS L99

Mods = Not enough....
G701LE is offline   Reply With Quote
Old 06-08-2016, 06:25 PM   #8
alvinmiles
 
alvinmiles's Avatar
 
Drives: 2011 Camaro 2SS - Black
Join Date: Dec 2014
Location: Lexington, KY
Posts: 42
Quote:
Originally Posted by G701LE View Post
Did you undo the steering shaft when you installed the headers?
I did
__________________
Posting all mods as i go, along with other non sense.

http://m.youtube.com/channel/UCJY1FzsIqSAtCJxZdYeuz-A
alvinmiles is offline   Reply With Quote
Old 06-08-2016, 06:38 PM   #9
jayno20
Go fast, please.
 
jayno20's Avatar
 
Drives: 2014 Camaro ZL1, 2015 Corvette Z06
Join Date: May 2014
Location: Pittsburgh, PA
Posts: 2,388
Quote:
Originally Posted by MMC View Post
Check the plug wires.
This. I got the same lights and then I realized I left one plug wire off when tightening down the header bolts.
jayno20 is offline   Reply With Quote
Old 06-09-2016, 01:44 PM   #10
alvinmiles
 
alvinmiles's Avatar
 
Drives: 2011 Camaro 2SS - Black
Join Date: Dec 2014
Location: Lexington, KY
Posts: 42
just finished with new plug installation. made sure all plug wires were snug. usually the code throws as soon as i start rolling. thought it was fixed....for a moment.

its back.
__________________
Posting all mods as i go, along with other non sense.

http://m.youtube.com/channel/UCJY1FzsIqSAtCJxZdYeuz-A
alvinmiles is offline   Reply With Quote
Old 06-09-2016, 02:19 PM   #11
C62SSFTW
 
Drives: 2015 Camaro 2SS
Join Date: Dec 2015
Location: Tampa
Posts: 15
"G701LE" is on the right track. I used to own a Pontiac G8 GT (witch shares a platform with us), I saw this happen many times with other people when doing headers. We had to disconnect the steering shaft to install the headers. When you reconnect it, it needs to be put back in the exact same position as when it was removed. I used a black sharpie to mark this. If the shaft turned to a different position be fore reassembly, there is a sensor that detects the position of the steering to help with stability control. When miss aligned what you are describing above will happen.

If you know how much it turned by just realign it, if not, tail and error. I have also heard this may be reconfigure thought tuning software, but do not know for certain.

Last edited by C62SSFTW; 06-09-2016 at 02:38 PM.
C62SSFTW is offline   Reply With Quote
Old 06-09-2016, 03:48 PM   #12
G701LE

 
G701LE's Avatar
 
Drives: 2010 2SS/RS L99 IBM silver stipes
Join Date: Dec 2015
Location: K.C. Kansas
Posts: 1,335
Yes. I learned the hard way (as usual) about the steering shaft. Had to take it to someone that can "reset" or "relearn" the steering. If it is off AT ALL, it will throw these codes.
__________________
2010 Imperial Blue w/ Silver stripes 2SS/RS L99

Mods = Not enough....
G701LE is offline   Reply With Quote
Old 06-09-2016, 03:56 PM   #13
alvinmiles
 
alvinmiles's Avatar
 
Drives: 2011 Camaro 2SS - Black
Join Date: Dec 2014
Location: Lexington, KY
Posts: 42
Yes i think that's right. It doesn't come on until i turn left. So tomorrow I'll disconnect it and turn 1 rotation to the right. Thanks a lot guys and I'll keep u posted. Btw at least i got new plugs.
__________________
Posting all mods as i go, along with other non sense.

http://m.youtube.com/channel/UCJY1FzsIqSAtCJxZdYeuz-A
alvinmiles is offline   Reply With Quote
Old 06-09-2016, 06:55 PM   #14
spadz93
BUMBL Z
 
spadz93's Avatar
 
Drives: 2015 ZL1
Join Date: Nov 2013
Location: Norwood NJ
Posts: 2,433
I'd still check plugs/wires. Seen three camaros throw stabilitrak messages after header installs and most were loose/damaged plugs/wires
__________________
Current: 2015 ZL1 M6, Rotofab, VMAX Throttle body, 2.55 Upper/8.86 Lower Pulleys, ID1050X, 1 7/8" Headers, 614rwhp/616rwtq
Past: 2010 2SS, some bolt ons, 415rwhp/400rwtq
spadz93 is offline   Reply With Quote
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:29 AM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2018, vBulletin Solutions, Inc.