Front Bowie and SS emblem removal - Page 3 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

Mels RS · 09-15-2015, 04:51 PM

Quote:

Originally Posted by i-Guy

And one more while I have your attention...I asume the following to be true. All of these embelems are glued on a 2014 SS with no holes after removal:
1) Side Camaro emblems
2) Rear SS
3) Rear Bow tie
Thanks for the help...

This is definitely true of the 2015. I'm pretty sure that the 2014 is the same.

MYLSA · 09-16-2015, 07:46 AM

Quote:

Originally Posted by Mels RS

This is definitely true of the 2015. I'm pretty sure that the 2014 is the same.

Thanks...but can someone also answer my first question...Please. If I remove the SS from the front grill on a 2014 2SS will it just look like the other side of the grill where there is no SS? or is there some type of indentation or somehting from where the SS was installed?

Moto-Mojo · 09-16-2015, 10:06 AM

Demon War Horse · 09-16-2015, 10:52 AM

Quote:

Originally Posted by Mels RS

This is definitely true of the 2015. I'm pretty sure that the 2014 is the same.

True on a 2014 also.

BLU DUCE · 09-16-2015, 10:59 AM

Quote:

Originally Posted by i-Guy

Thanks...but can someone also answer my first question...Please. If I remove the SS from the front grill on a 2014 2SS will it just look like the other side of the grill where there is no SS? or is there some type of indentation or somehting from where the SS was installed?

I'm beginning to think no 1 can answer this question. Once you take the SS it is not like the other side.
But they sell a black flat insert that goes over where you removed the SS.

MYLSA · 09-16-2015, 11:27 AM

Quote:

Originally Posted by spike III

I'm beginning to think no 1 can answer this question. Once you take the SS it is not like the other side.
But they sell a black flat insert that goes over where you removed the SS.

Thanks...and when you say "they sell" I assume Chevy?

Vono27 · 04-18-2017, 12:43 PM

Bowtie and ss emblem rear is adhesive tape, bowtie front and ss emblem front are held in by clips. Took a hour tops to remove all and wipe down whatever adhesive glue left. Be careful not to scratch or chip paint. I did at the rear with Bow tie.

PalmerGA · 04-18-2017, 07:32 PM

Quote:

Originally Posted by christianchevell

you have a heritage grill? remove the panel that supports the hood latch the front bumper will flex as you slide it out towards the engine to clear the latch by warping the front bumper/frontend then you can get your hand in...did this to install my retro ss badges....If you do not have the heritage grill they make pieces to patch where the bowtie was in the grill as it is missing the structure to look right.

Yup. It's a slightly different procedure with a heritage grille, but well worth it.
Name: Front Reduced.jpg
Views: 368
Size: 42.2 KB

09-16-2015, 10:06 AM	#31
Moto-Mojo Fast Cars and Old Guitars Drives: 2015 2SS RS (L99, baby!) Join Date: Apr 2012 Location: N. CA Posts: 3,973	__________________ “I don’t want to belong to any club that would have me as a member.” - Groucho Marx

04-18-2017, 12:43 PM	#35
Vono27 Drives: 2012 Camaro SS Join Date: Mar 2017 Location: Miami Gardens Posts: 4	Bowtie and ss emblem rear is adhesive tape, bowtie front and ss emblem front are held in by clips. Took a hour tops to remove all and wipe down whatever adhesive glue left. Be careful not to scratch or chip paint. I did at the rear with Bow tie.