04-23-2010, 01:56 PM | #1 |
Drives: 2010 2SSRS Join Date: Sep 2009
Location: Indiana
Posts: 121
|
Any Threads on removing the Stock Head unit?
Has anyone done a good howto on removing the stock head unit. I did some searching but didn't find anything.
thanks
__________________
2010 2SSRSA6 - GFX
35% Window Tint 93 Octane Diablo Predator Tune |
04-23-2010, 02:47 PM | #2 |
SoCal Mayhem
Drives: 2010 Camaro 1SS/RS Join Date: Aug 2008
Location: Foothill Ranch, CA
Posts: 5,488
|
With a dash trim removal tool, pry up on the shifter bezel releasing all clips
Shift shifter to “M” (or neutral if M6) and remove the shifter bezel Remove (2) 7mm screws from the bottom of the radio bezel Remove 2 remaining screws on radio Pull radio out
__________________
|
04-26-2011, 07:42 PM | #3 |
Account Suspended
Drives: 2011 Camaro LS Join Date: Dec 2010
Location: NY
Posts: 1,117
|
Dont mean to bump a really old thread but is it really that easy??
|
04-26-2011, 07:53 PM | #4 |
"Camaro Joe"
|
if you need pictures check out the diy on the hud in the diy section
|
04-26-2011, 10:26 PM | #5 |
Drives: 2010 CGM 2SS/RS Join Date: Feb 2011
Location: Upland
Posts: 104
|
When I had my Metra kit installed, I took a few pictures. Here is one with the head unit removed. With "slick rick's" directions, you will be able to see what screws and locations he is referring to
The gauge panel will have to be removed in order to access the two screws on the bottom. You can see the screw holes where "slick rick" has made reference to. You can also see the areas where you are going to have to focus on with your pry tool. Hope this helps. Allen
__________________
'69 SS Camaro 2SS/RS, CGM, Magnaflow Exhaust, Pfadt Suspension, Airaid intake (Sold) 71 RS Camaro (Sold) Z Car (Sorry, Nissan 350Z) |
04-26-2011, 10:37 PM | #6 |
Account Suspended
Drives: 2011 Camaro LS Join Date: Dec 2010
Location: NY
Posts: 1,117
|
Does the console really need to be pulled apart that far?? Was hoping it was just where the 4 pack gauges would be?? I have to pull it out to hook up my pac connector for RCAs.
|
04-27-2011, 12:20 AM | #7 |
Drives: IBM 2SS Join Date: Jan 2011
Location: San Antonio, TX
Posts: 858
|
Use this
http://youtu.be/Cktl99S4O_U |
04-27-2011, 01:27 PM | #8 |
Drives: 2010 CGM 2SS/RS Join Date: Feb 2011
Location: Upland
Posts: 104
|
Actually, my installer, pulled out the console, so he could get to all the wiring. But I don't believe you have to actually pull it back that far. Not 100% sure though...... Primarily, that panel that houses the gauges needs to be removed.
__________________
'69 SS Camaro 2SS/RS, CGM, Magnaflow Exhaust, Pfadt Suspension, Airaid intake (Sold) 71 RS Camaro (Sold) Z Car (Sorry, Nissan 350Z) |
04-27-2011, 01:50 PM | #9 |
"Camaro Joe"
|
you need to put the top with the 4pac gauges off, this way you can get to the screws, it should take about 1 or 2 mins to get off completly
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Are the Boston Acoustics & base head unit the same? | hdhomer | Audio, Video, Bluetooth, Navigation, Radar, Electronics Forum | 34 | 01-19-2012 12:54 AM |
Tips for First Timer | MrCool | 4th Generation Camaros | 123 | 10-31-2009 07:37 PM |
Be careful cleaning Head Unit Screen | tjd24 | Audio, Video, Bluetooth, Navigation, Radar, Electronics Forum | 8 | 05-29-2009 06:05 PM |
Bad news for anyone thinking of installing an aftermarket head unit | fastball | Audio, Video, Bluetooth, Navigation, Radar, Electronics Forum | 26 | 05-26-2009 10:18 PM |
Song Information Displayed on Head Unit | ravensjeff | Audio, Video, Bluetooth, Navigation, Radar, Electronics Forum | 32 | 03-16-2009 04:28 PM |