Premium 370.1 ring and pinion - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

nuptualnemesis · 11-26-2010, 03:04 AM

SOLD!

AAM 370 gear for $550.00 plus $50.00 shipping in unopened box. From RPM Transmissions, Decided to go with the 433. They have this gear listed on Ebay for $850.00 plus $50.00 shipping.

http://cgi.ebay.com/ebaymotors/ws/eB...tchlink:top:en

(I assume the gear they sent me is polished but box still unopened. This was the only gear they would provide a warranty for because it is used by GM (OEM Gear) in some of their vehicles.)

(Correction: Mine is not polished.)

flht99b · 11-29-2010, 05:14 AM

Sent a PM several days ago.
Ed M.

nuptualnemesis · 12-01-2010, 02:38 PM

I may have taken a picture of the wrong gear that was on the shelf at Thunder Racing. It appears that Motive does not make a 2010 camaro gear. I am going to try to get a picture of the correct gear.

This is the AAM and it is black not polished. RPM lists this on their web site for $799.00. It is a much better gear than Richmond.

nuptualnemesis · 12-30-2010, 02:15 PM

I also have a set of the Jannetty racing 2010 Camaro SS JRE Billet Caps which were $169.99 plus $9.95 processing fee and $15.00 shipping that I will sell for $150.00 (new still in box)

94guy · 12-31-2010, 09:57 AM

why are you selling them?

nuptualnemesis · 01-05-2011, 10:37 AM

I decided to go with a 4:33. I had a Center section from RPM transmissions ($2,000.00) with the 3:70. It was loud and got worse. Sent it back for warranty repair and they replaced it, under warranty, and it was quite and worked great. Put in Ram clutch (bad idea for drag racing launch) and broke in clutch and gear for 500 miles. First time at the track I broke the posi with 4 or 5 wheel hops. Could have been bad already but I think the differential bushings from pfadt contributed. Stick with stock bushings they absorb vibration. I now have the new BMR bushings and put in an bigger bolt to take up all of the slack. I strongly recommend this even for stock bushings. Also upgrade the drive shaft bolts and loctite them.

Sent it back to RPM for warranty and they refused to honor the warranty listed on the website. I sent them a Jannetty posi upgrade kit and paid for new posi no labor. Told them to upgrade to 4:33 gear and they said extra $800.00. This was after they sent me pics of shredded parts and being told they did not recommend using old gear. Told them if it was noisy it was going back. It was super noisy in the driveway leaving Thunder racing.

After threats of litigation they finally agreed to send a new ADM 3:70 and install kit because I refused to send my center section back to them. They kept it a month the first time and month and half the second time.

I had Zimmer gears on choctaw in Baton Rouge install a 4:33 and they did an excellent job. They set it up really tight and they know what they are doing. They even called to ask if it was quiet and if I was satisfied. Their price was more than reasonable with a two day turn around.
So I have an extra 3:70. A couple of members have advised they will have the money after the holidays.

FiveO · 01-29-2011, 11:23 PM

How much did Zimmer charge you for install?

2010 SSRS · 01-29-2011, 11:44 PM

I had 370's in my 87 5.7 IROC, that is an awesome gear.

nuptualnemesis · 02-01-2011, 01:57 PM

Zimmer under charged me and told me not to tell anyone what he charged. A lot lot less than what Jannety wanted. He called to ask if they were quiet and how I liked them a week later. They put them in in two days. They are starting to hum a little around 60mph but still pretty damn quiet. I have been abusing them at the track as usual.

kook · 02-01-2011, 02:18 PM

Are these still available?

2010 2-Tone · 02-01-2011, 02:27 PM

What is your best time with the 4.33's?

nuptualnemesis · 02-07-2011, 05:03 PM

Quote:

Originally Posted by kook

Are these still available?

Yes. I still have them.

nuptualnemesis · 02-07-2011, 05:04 PM

Quote:

Originally Posted by 2010 2-Tone

What is your best time with the 4.33's?

Made a few passes but don't have the launch down yet. Ran 11.82 with 1.88 sixty foot and 121.4 mph. The top end picked up 2 mph but my 1/8 mile was 2-3 mph slower than before. I don't think I wound out 1st and 2nd enough. Also the track may have been too cold for traction. Going through the traps around 6,400 - 6,500 rpm with the 17" rims and 27.5' tall Mickey Thompson 295/45/17 drag radial.

nak3dsnake · 02-12-2011, 06:54 PM

Do you still have this?

11-26-2010, 03:04 AM	#1
nuptualnemesis NuptualNemesis Drives: Silver 1SS M6 - 480hp 11.57/120.79 Join Date: Jul 2009 Location: Baton Rouge, LA www.Divorcefor399.com Posts: 310 View My Garage	Premium 370.1 ring and pinion SOLD! AAM 370 gear for $550.00 plus $50.00 shipping in unopened box. From RPM Transmissions, Decided to go with the 433. They have this gear listed on Ebay for $850.00 plus $50.00 shipping. http://cgi.ebay.com/ebaymotors/ws/eB...tchlink:top:en (I assume the gear they sent me is polished but box still unopened. This was the only gear they would provide a warranty for because it is used by GM (OEM Gear) in some of their vehicles.) (Correction: Mine is not polished.) Last edited by nuptualnemesis; 03-18-2011 at 03:13 PM. Reason: Correction

11-29-2010, 05:14 AM	#2
flht99b Drives: 2010 Camaro 2SS/RS RJT Join Date: May 2009 Location: Knoxville Posts: 1,574 View My Garage	Sent a PM several days ago. Ed M. __________________ RJT 2SS/RS, AAM 3.70's, MTI Sway Bars, Shifter & SS brake lines, ZLI calipers, rotors & pads, BMR Trailing & Toe Arms, rear cradle & diff bushes, Pedders XA's, Camber/Toe eccentrics, Radius arm inserts, GTO clutch reservoir, LS9 cam, Comp valve springs, Melling 10296 oil pump, CR5 timing chain, LS6 damper, CAI Cold Air Intake, ARH LT headers w/HF cats, GMPP touring axle back, Elite Engineering Catch Can, Forgeline 20x9.5 & 20x11 DS3 whls, 275/40/20 & 315/35/20 tires, 2011 Convertible spoiler, 1LE front spoiler, Lloyd "SS" Floor Mats, GM Camaro Trunk Mat, wrapped console & Grant steering wheel.

12-01-2010, 02:38 PM	#3
nuptualnemesis NuptualNemesis Drives: Silver 1SS M6 - 480hp 11.57/120.79 Join Date: Jul 2009 Location: Baton Rouge, LA www.Divorcefor399.com Posts: 310 View My Garage	I may have taken a picture of the wrong gear that was on the shelf at Thunder Racing. It appears that Motive does not make a 2010 camaro gear. I am going to try to get a picture of the correct gear. This is the AAM and it is black not polished. RPM lists this on their web site for $799.00. It is a much better gear than Richmond. Attached Images Last edited by nuptualnemesis; 12-03-2010 at 11:02 AM. Reason: wrong picture

01-29-2011, 11:44 PM	#8
2010 SSRS Drives: 3 V8 Camaros Join Date: May 2009 Location: The Ocean State Posts: 111,187 View My Garage	I had 370's in my 87 5.7 IROC, that is an awesome gear. __________________ Jannetty Racing JRE Street Package

02-01-2011, 02:18 PM	#10
kook Drives: 2010 2SS Yellow Join Date: May 2010 Location: Indiana Posts: 548 View My Garage	Are these still available? __________________ Edelbrock E-Force Stainless Works Lts Roto Fab CAI Magnaflow Street Cat-Back DOD Delete Forgestar F-14's and Pedders XA + PKG Custom grind cam from Cincy Speed ADM dual fuel pump ADM AF/Boost gauges FTI 3200 convertor Hurst shifter Cincy Speed Build and Tune 540rwhp

12-30-2010, 02:15 PM	#4
nuptualnemesis NuptualNemesis Drives: Silver 1SS M6 - 480hp 11.57/120.79 Join Date: Jul 2009 Location: Baton Rouge, LA www.Divorcefor399.com Posts: 310 View My Garage	I also have a set of the Jannetty racing 2010 Camaro SS JRE Billet Caps which were $169.99 plus $9.95 processing fee and $15.00 shipping that I will sell for $150.00 (new still in box)

12-31-2010, 09:57 AM	#5
94guy Drives: 99 Camaro; 2010 Camaro 2SS/RS Join Date: Nov 2009 Location: louisiana Posts: 1,966	why are you selling them?

01-05-2011, 10:37 AM	#6
nuptualnemesis NuptualNemesis Drives: Silver 1SS M6 - 480hp 11.57/120.79 Join Date: Jul 2009 Location: Baton Rouge, LA www.Divorcefor399.com Posts: 310 View My Garage	I decided to go with a 4:33. I had a Center section from RPM transmissions ($2,000.00) with the 3:70. It was loud and got worse. Sent it back for warranty repair and they replaced it, under warranty, and it was quite and worked great. Put in Ram clutch (bad idea for drag racing launch) and broke in clutch and gear for 500 miles. First time at the track I broke the posi with 4 or 5 wheel hops. Could have been bad already but I think the differential bushings from pfadt contributed. Stick with stock bushings they absorb vibration. I now have the new BMR bushings and put in an bigger bolt to take up all of the slack. I strongly recommend this even for stock bushings. Also upgrade the drive shaft bolts and loctite them. Sent it back to RPM for warranty and they refused to honor the warranty listed on the website. I sent them a Jannetty posi upgrade kit and paid for new posi no labor. Told them to upgrade to 4:33 gear and they said extra $800.00. This was after they sent me pics of shredded parts and being told they did not recommend using old gear. Told them if it was noisy it was going back. It was super noisy in the driveway leaving Thunder racing. After threats of litigation they finally agreed to send a new ADM 3:70 and install kit because I refused to send my center section back to them. They kept it a month the first time and month and half the second time. I had Zimmer gears on choctaw in Baton Rouge install a 4:33 and they did an excellent job. They set it up really tight and they know what they are doing. They even called to ask if it was quiet and if I was satisfied. Their price was more than reasonable with a two day turn around. So I have an extra 3:70. A couple of members have advised they will have the money after the holidays.

01-29-2011, 11:23 PM	#7
FiveO Drives: 2011 Camaro SS 6speed Manual Join Date: Sep 2010 Location: Baton Rouge, LA Posts: 128 View My Garage	How much did Zimmer charge you for install?

02-01-2011, 01:57 PM	#9
nuptualnemesis NuptualNemesis Drives: Silver 1SS M6 - 480hp 11.57/120.79 Join Date: Jul 2009 Location: Baton Rouge, LA www.Divorcefor399.com Posts: 310 View My Garage	Zimmer under charged me and told me not to tell anyone what he charged. A lot lot less than what Jannety wanted. He called to ask if they were quiet and how I liked them a week later. They put them in in two days. They are starting to hum a little around 60mph but still pretty damn quiet. I have been abusing them at the track as usual.

02-01-2011, 02:27 PM	#11
2010 2-Tone Drives: 2010 RY 2SS with Custom Stripes Join Date: Mar 2009 Location: Jennings, La. Posts: 2,220 View My Garage	What is your best time with the 4.33's?

02-12-2011, 06:54 PM	#14
nak3dsnake Drives: 2010 Camaro IBM 2LT/RS M6 Join Date: Sep 2009 Location: Columbus, OH Posts: 2,282 View My Garage	Do you still have this? __________________ Looks: AAC P13W DRLs, Heritage Grille, RS Embroidered Headrests, GM Door Sill Plates, GM Premium Floor Mats, Body Color Engine Cover, LLT Mobile 1 Oil Cap, ZL1 Sport Pedals, 3M Clear Bra. Performance: Vararam Ram Air Intake, Hurst Short Throw Shifter w/ Hurst Hard Drive Pistol Grip, IDEALG Clutch Master Cylinder, RX Catch can, GTO clutch fluid reservoir, Brembo Brakes, 1LE Track Pack, GMPP Exhaust Upgrade.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
FS BARTON SHORT THROW SHIFTER AND RICHMON 4:10 RING AND PINION	stephancamaro	Transmission / Driveline	7	11-24-2010 06:33 PM
WTB 3.73s	jay11	V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6)	10	09-10-2010 06:59 AM
Ring & Pinion INSTALL KITS.	Qwkss	V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6)	14	03-30-2010 11:25 PM
Ring & Pinion Swap Out	SJ LYNN	V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6)	15	02-18-2010 07:44 PM
Is a ring and pinion whine normal for 2002 V6?	TopFuelTim	4th Generation Camaros	7	04-09-2009 07:51 PM