ZL1 Front Air Dam Skid Plate Taking Orders Now!! - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

autoguy · 02-20-2013, 05:20 PM

For all of you that waited so patiently, we have pics, details and are ready to start taking orders!!!

We have two versions, a High Density Plastic version and a T6061 Aluminum version. Both are 5 pieces for easy handling and less expensive shipping, and it lowers the cost as well.

The Plastic one is Black and the Aluminum one is a bead blasted natural aluminum finish.

Easy 15 minute install using factory screws, All that is needed is a T-20 Torx bit. It can be done with the car on the ground as well!!

Prices listed are special Forum Intro Prices. We will hold these prices for at least the first 20-30 units sold and longer if there is a higher interest.

Since we do not know the mix of how many of each are made, the first batch of orders will be a pre order. We did not have any other than the prototype made yet, so initial lead time will be about 1-2 weeks. If we see one or the other material is selling much better, we will have a stock order made.

More details and orders can be placed here.....

http://www.ridergraphix.com/Camaro_ZL1_Nose_Plate.html

[IMG]http://www.ridergraphix.com/ZL1_Skid3a.jpg[/IMG]

[IMG]http://www.ridergraphix.com/Splitter5.jpg[/IMG]

[IMG]http://www.ridergraphix.com/ZL1_Skid6a.jpg[/IMG]

autoguy · 02-20-2013, 08:43 PM

Can a Mod Please delete this thread, I revised it to include pics and somehow it was duplicated.

02-20-2013, 05:20 PM	#1
autoguy Drives: 10 SS,11 SS Pace, 13 ZL1 IOM Join Date: Oct 2008 Location: Pennsylvania Posts: 1,733 View My Garage	ZL1 Front Air Dam Skid Plate Taking Orders Now!! For all of you that waited so patiently, we have pics, details and are ready to start taking orders!!! We have two versions, a High Density Plastic version and a T6061 Aluminum version. Both are 5 pieces for easy handling and less expensive shipping, and it lowers the cost as well. The Plastic one is Black and the Aluminum one is a bead blasted natural aluminum finish. Easy 15 minute install using factory screws, All that is needed is a T-20 Torx bit. It can be done with the car on the ground as well!! Prices listed are special Forum Intro Prices. We will hold these prices for at least the first 20-30 units sold and longer if there is a higher interest. Since we do not know the mix of how many of each are made, the first batch of orders will be a pre order. We did not have any other than the prototype made yet, so initial lead time will be about 1-2 weeks. If we see one or the other material is selling much better, we will have a stock order made. More details and orders can be placed here..... http://www.ridergraphix.com/Camaro_ZL1_Nose_Plate.html [IMG]http://www.ridergraphix.com/ZL1_Skid3a.jpg[/IMG] [IMG]http://www.ridergraphix.com/Splitter5.jpg[/IMG] [IMG]http://www.ridergraphix.com/ZL1_Skid6a.jpg[/IMG]

02-20-2013, 08:43 PM	#2
autoguy Drives: 10 SS,11 SS Pace, 13 ZL1 IOM Join Date: Oct 2008 Location: Pennsylvania Posts: 1,733 View My Garage	Can a Mod Please delete this thread, I revised it to include pics and somehow it was duplicated.