1LE Suspension Package Part Numbers

[Norm Peterson]

Originally Posted by camaro789

hi bud after install the kit, does a wheel alignment needed ?

Any time that you change the car's ride height or disassemble its suspension for any reason, you need to at least check the alignment. It may be good, close enough, or not and needs adjustment.

Just the clearances in the various holes for the bolts that go through them may allow the bolts to not go back together exactly the way they were before.

Kind of separate, but when you swap in all those parts which are intended for harder cornering you'll probably want a fussier and more aggressive alignment than OE for an SS to take better advantage of it all.


Norm

[srsmithee]

I was poking around partstaxi.com and they have a package for 1LE suspension minus hubs and rear cradle bushings. The part numbers they list do not match with those I've seen on this thread. Is there something I'm missing?

http://www.partstaxi.com/products.php?partID=1651

22812942 Front Stab Bar Asm (bar, links, bushing, clamp, nut) 1
22786260 Rear Stab Bar Asm (bar, bushing, clamp, bolt) 1
22761221 Rear Stab Bar Link 2
22812982 Front Strut Asm, LH (strut, spring, mount) 1
22812983 Front Strut Asm, RH (strut, spring, mount) 1
22981391 Rear Shock 2
22922445 Rear Shock Mount, LH 1
22922446 Rear Shock Mount, RH 1
22845487 Rear Toe Link 2

[camaro789]

what wheel alignment spec shall i use ? FE2 or FE6 ? I can't find FE6 spec, thank you !

Originally Posted by Norm Peterson

Any time that you change the car's ride height or disassemble its suspension for any reason, you need to at least check the alignment. It may be good, close enough, or not and needs adjustment.

Just the clearances in the various holes for the bolts that go through them may allow the bolts to not go back together exactly the way they were before.

Kind of separate, but when you swap in all those parts which are intended for harder cornering you'll probably want a fussier and more aggressive alignment than OE for an SS to take better advantage of it all.


Norm

[wakespeak]

Anyone else confirm that going from 2013 FE4 to 1LE FE6 is just the rear shocks and shock "bumpers", f/r sway bars, wheel bearings, and cradle bushings? Everything else looks same as FE4 including springs and front struts.

[porkrind]

Fairly sure it was mentioned that front struts were monotube.

Sent from my ADR6425LVW using Tapatalk 4

[Mikk2K]

I already have upgraded endlinks and sways that fit into my 2010 FE2. If I just wanted to upgrade to the 1LE shocks and struts my endlinks wouldn't fit any more is that correct?

[sycraft]

Originally Posted by Mikk2K

I already have upgraded endlinks and sways that fit into my 2010 FE2. If I just wanted to upgrade to the 1LE shocks and struts my endlinks wouldn't fit any more is that correct?

Correct

[Chevy9534]

One quick question, If i buy the 1LE sways are endlinks needed as well. These will be going on a 2013 ss.

[sycraft]

Originally Posted by Chevy9534

One quick question, If i buy the 1LE sways are endlinks needed as well. These will be going on a 2013 ss.

Yes

[salvagelife]

bump ...are the rear toe link needed , i have a 2010 camaro ss and upgardind just the sway bar

[JusticePete]

Originally Posted by salvagelife

bump ...are the rear toe link needed , i have a 2010 camaro ss and upgardind just the sway bar

Needed, no. Better, yes.

[salvagelife]

Originally Posted by JusticePete

Needed, no. Better, yes.

thank you for the quick replied just making sure before i oder ,i have the pfadt trailing arm and toe rod combo

[salvagelife]

I'm having an issued I'm installing 1le front sway bar and notice the end link are thicker , from reading here people are mentioning the bolt are 12mm for the end link ,I have a 2010 with 10mm , anyways my issue is I don't have 12mm bolt does anyone the the pn # for the bolts ?

[salvagelife]

Ok so I have to drill a larger hole where the upper end link connects to the strut bracket part since is made for a 10mm on my coilovers .