11-29-2010, 09:04 PM | #1 |
Drives: 2005 corvette coupe Join Date: Nov 2009
Location: new mexico
Posts: 34
|
CNC Ported PRC Heads with springs
i have a set of used PRC LS3 CNC Ported heads. These heads were used all of about 500 miles. I have decided to go another direction. they are in perfect condition and ready to bolt on.
They come with the stainless steel valves and PRC double springs good to .675 lift. the set new would cost just over 1600. I will let these go for 1100 plus shipping. |
11-30-2010, 03:09 PM | #2 |
Drives: 2005 corvette coupe Join Date: Nov 2009
Location: new mexico
Posts: 34
|
bumpity
|
12-05-2010, 02:20 AM | #3 |
Drives: 2005 corvette coupe Join Date: Nov 2009
Location: new mexico
Posts: 34
|
TTT lots of lookers, no one for sure yet
|
12-05-2010, 01:04 PM | #4 |
"Black Ace"
Drives: Supercharged 2010 SS, 2016 Golf R Join Date: Aug 2008
Location: Ft. Lauderdale, FL
Posts: 1,352
|
Perhaps because you can get a new set for less than you're asking from Texas Speed? Someone feel free to correct me if I'm wrong.
__________________
2010 2SS/RS M6 "Black Ace" - Delivered 6/4/2009
Mods: Forged 416 LS3, Maggie TVS 2300 SC (~11 psi), custom cam (232/247, .630/.630, 118 LSA), 90-lb. injectors, ZL1 fuel pump & ADM controller, Alky Control meth kit, Monster LT1-SC twin-disk clutch, ZL1 drivetrain conversion w/ DSS 1000-HP axles & 1-pc. driveshaft, CAI Inc. intake w/ ADM scoop, XS Power full exhaust (1 7/8" LT headers with 3" off-road pipes), VMAX CNC-ported TB, LSR adjustable sway bars, LPE rear end-links, BMR 1" drop, BMR polyurethane bushings; UMI trailing arms & toe rods. Built & tuned by Kraftworks. 755 rwhp/708 rwtq |
12-05-2010, 01:44 PM | #5 |
Drives: 2010 2ssrs Join Date: Nov 2010
Location: Miami
Posts: 205
|
I just recently bought these.Base cnc ls3 l92 prc heads and milling and new oem valves.Isent my springkit and this was cost.1299.99 plus shipping63.58 OP has more expensive valves and is included springs .
|
12-05-2010, 02:52 PM | #6 | |
Drives: 2011 SS/RS LS3 Join Date: Oct 2010
Location: Miami
Posts: 528
|
Quote:
|
|
12-05-2010, 03:05 PM | #7 |
Drives: 2005 corvette coupe Join Date: Nov 2009
Location: new mexico
Posts: 34
|
|
12-05-2010, 03:08 PM | #8 |
Drives: blacked out 2010 Camaro Join Date: May 2009
Location: Denver Colorado
Posts: 626
|
Will theses heads work for l99
|
12-05-2010, 04:05 PM | #9 |
"Black Ace"
Drives: Supercharged 2010 SS, 2016 Golf R Join Date: Aug 2008
Location: Ft. Lauderdale, FL
Posts: 1,352
|
I see; that makes sense now. Thanks for clarifying.
__________________
2010 2SS/RS M6 "Black Ace" - Delivered 6/4/2009
Mods: Forged 416 LS3, Maggie TVS 2300 SC (~11 psi), custom cam (232/247, .630/.630, 118 LSA), 90-lb. injectors, ZL1 fuel pump & ADM controller, Alky Control meth kit, Monster LT1-SC twin-disk clutch, ZL1 drivetrain conversion w/ DSS 1000-HP axles & 1-pc. driveshaft, CAI Inc. intake w/ ADM scoop, XS Power full exhaust (1 7/8" LT headers with 3" off-road pipes), VMAX CNC-ported TB, LSR adjustable sway bars, LPE rear end-links, BMR 1" drop, BMR polyurethane bushings; UMI trailing arms & toe rods. Built & tuned by Kraftworks. 755 rwhp/708 rwtq |
12-05-2010, 04:30 PM | #10 |
Drives: 2005 corvette coupe Join Date: Nov 2009
Location: new mexico
Posts: 34
|
|
12-07-2010, 09:59 AM | #11 |
Drives: 2005 corvette coupe Join Date: Nov 2009
Location: new mexico
Posts: 34
|
Sold..thanks
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Ported Heads & Options for LS3 | calbert1999 | Tuning / Diagnostics -- engine and transmission | 32 | 02-24-2011 05:18 PM |
Hotchkis: Tuned Suspension Setups | Springs | Chassis Brace | Sway Bars | FREE S&H | AJ@ECSMotorsports | Suspension / Chassis / Brakes | 80 | 11-17-2010 02:28 PM |
Maximize Your Suspension ~ Hotchkis Swaybars, Springs and Chassis Braces! | Circuit Motorsports | Suspension / Chassis / Brakes | 99 | 05-24-2010 04:21 PM |
Want to Lower Your Camaro? Step Inside! Eibach Springs and Sways Now Shipping! | Kris@BMCPerformance | Suspension / Chassis / Brakes | 20 | 01-15-2010 09:09 PM |
Heads and cam combo-MDinduction | matt d. | V8 Bolt-Ons & Tunes | 8 | 11-06-2009 02:59 PM |