Wheel spacers - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

avido · 01-24-2018, 02:51 PM

Guys, i was looking at the car and i started thinkig about a pair of spacers, to give the car a better look. I was wondering if someone used it and what size to buy. is 20mm too much?

mantarey · 01-24-2018, 03:21 PM

Not sure how thick 20mm is but I have 1/4 on my car

frankwjr · 01-24-2018, 03:21 PM

I have been using the H&R Trak+ DRM 30mm 6075670 on all 4 corners for about a year now. Pushed the stock rims out nicely and IMHO improved handling some....left them on when I went drag racin too! good luck!

avido · 01-24-2018, 03:41 PM

thanks. i was looking for these
Hr 4075670

In italy, where i leave, if the wheels are out more than the body you risk the impound

bowtiesonly · 01-24-2018, 06:03 PM

I use 1/4 aluminum spacers, had them for five years and have worked great, pushed wheels just about flush with body.

Carlos_MRRWheelsInc · 01-25-2018, 02:05 PM

Wheel spacers are good just as long as you get some that are hub centric to your vehicle and also hub centric to the wheels you are installing, at that point is the best possible fitment you can have using a spacer.

01-24-2018, 02:51 PM	#1
avido Drives: camaro ss\rs Join Date: Jun 2014 Location: Italia Posts: 755	Wheel spacers Guys, i was looking at the car and i started thinkig about a pair of spacers, to give the car a better look. I was wondering if someone used it and what size to buy. is 20mm too much? __________________ 2014 camaro SS Whipple powered ,3.750 pulley,ID850, CAI,Flowmaster American Thunder exhaust,MGW racing shifter,Bo White ported tb,MightyMouse Catch Can,Vitesse throttle controller,GM 3.91 rear end, Dynatech longtube haders, BTR Pd cam,Fluidampr stock pulley,ZL1 fuel pump and ADM fpcm, Phastek scoop and fluid thank relocation Bmr Motor mount . Tuned by Mastuning

01-24-2018, 03:21 PM	#3
frankwjr Drives: 2010 SS 2SS M6 Join Date: Aug 2016 Location: Smithsburg, Md. Posts: 2,445	I have been using the H&R Trak+ DRM 30mm 6075670 on all 4 corners for about a year now. Pushed the stock rims out nicely and IMHO improved handling some....left them on when I went drag racin too! good luck! __________________ 2010 SS 2SS M6 - Tune by RDP dynoSteve!(Woot) - Daily Driver - *150K!* - All work by me...

01-24-2018, 03:41 PM	#4
avido Drives: camaro ss\rs Join Date: Jun 2014 Location: Italia Posts: 755	thanks. i was looking for these Hr 4075670 In italy, where i leave, if the wheels are out more than the body you risk the impound __________________ 2014 camaro SS Whipple powered ,3.750 pulley,ID850, CAI,Flowmaster American Thunder exhaust,MGW racing shifter,Bo White ported tb,MightyMouse Catch Can,Vitesse throttle controller,GM 3.91 rear end, Dynatech longtube haders, BTR Pd cam,Fluidampr stock pulley,ZL1 fuel pump and ADM fpcm, Phastek scoop and fluid thank relocation Bmr Motor mount . Tuned by Mastuning

01-24-2018, 06:03 PM	#5
bowtiesonly Drives: 2012 Camaro 2ss Join Date: May 2012 Location: Arkansas Posts: 225 View My Garage	I use 1/4 aluminum spacers, had them for five years and have worked great, pushed wheels just about flush with body. __________________ 2012 2ss , long tube headers , summit x pipe ,borla mufflers, vararam intake, vmax ported throttle body rdp motorsports dynosteve tuned, BMR trailing arms and bushings elite engineering catch can. [Ifirst camaro ]2012 LT LFX, nytrex wet system ,GPI dyno tune, Injen longtube intake, Dynomax axle back exhaust, Vmax ported throttle body, elite engineering catch can.

01-24-2018, 03:21 PM	#2
mantarey Drives: 77corvette/2011blkcamaro Join Date: Oct 2009 Location: Deer Park Long Island Posts: 80	Not sure how thick 20mm is but I have 1/4 on my car

01-25-2018, 02:05 PM	#6
Carlos_MRRWheelsInc Drives: camaro Join Date: Nov 2011 Location: los angeles ca Posts: 404	Wheel spacers are good just as long as you get some that are hub centric to your vehicle and also hub centric to the wheels you are installing, at that point is the best possible fitment you can have using a spacer.