12-12-2014, 12:04 PM | #1 |
Drives: 2019 Chevy Equinox Premier AWD Join Date: Mar 2011
Location: Silicon Valley, CA
Posts: 1,344
|
ZL1 or Z/28 belly pan on a 2013 1LE
Has anyone installed the ZL1 underbelly pan or the Z/28 one?
Which one would fit/work better on a 2013 1LE? http://www.gen5diy.com/exterior/ZL1/zl1-belly-pan
__________________
2013 AGM 1SS/1LE, NPP, Camera
(1 of 43) Last edited by markgws6; 12-17-2014 at 12:08 PM. |
12-12-2014, 12:28 PM | #2 |
Drives: 2013 Camaro 1LE Join Date: Jul 2012
Location: Verona, WI
Posts: 1,930
|
I have considered looking into this as well. There was a similar discussion in the Z/28 section on the forum.
http://www.camaro5.com/forums/showthread.php?t=384030
__________________
|
12-12-2014, 01:35 PM | #3 |
Drives: '16 C7 Z51 Join Date: May 2012
Location: Redmond, WA
Posts: 3,056
|
I just got the Z/28 belly pan delivered. Hopefully I will put it on over the weekend. I do have a '14 1LE, though, not '13.
__________________
'16 Corvette C7 Z51 1LT (Build Thread)
'14 AGM 1SS 1LE [COTW 11/17/14] (Build Thread) (SOLD) '13 Mazda MX-5 Club (Build Thread) '17 RAM 1500 Crew Cab 4x4 Night Edition '15 Nissan Rogue S AWD |
12-12-2014, 01:43 PM | #4 |
Drives: 2022 SS 1LE Join Date: Jul 2013
Location: San Jose, CA
Posts: 1,086
|
Subscribed. Much to learn on the subject of high performance bellies
__________________
Sold but not forgotten! Pedders Supercar Coilovers, 32mm rear sway bar,bushings; APR wing and splitter
Forged 416 road course stroker. 514 RWHP, 497 RW Ft-Lb 1 Camaro, 75 Vipers: http://www.camaro5.com/forums/showthread.php?t=393697 Buttonwillow Raceway: http://www.camaro5.com/forums/showthread.php?t=389086 |
12-12-2014, 06:26 PM | #5 |
NEcamaro5
|
I'd like to know also.
|
12-12-2014, 06:57 PM | #6 |
Drives: 2011 2SS/RS LS3 Join Date: Nov 2011
Location: Torrance
Posts: 14,466
|
My $.02....Thought about a belly pan....but not until I get a vented hood to go with it....The belly pan helps draw out heat and add downforce to the front....Part of a "system"....I think without hood vents, the engine heat is drawn out underneath the car...so a belly pan by itself may not be any benefit...
Interesting topic....but a little hazy to me.... |
12-12-2014, 06:59 PM | #7 | |
Drives: '16 C7 Z51 Join Date: May 2012
Location: Redmond, WA
Posts: 3,056
|
Quote:
__________________
'16 Corvette C7 Z51 1LT (Build Thread)
'14 AGM 1SS 1LE [COTW 11/17/14] (Build Thread) (SOLD) '13 Mazda MX-5 Club (Build Thread) '17 RAM 1500 Crew Cab 4x4 Night Edition '15 Nissan Rogue S AWD |
|
12-12-2014, 09:50 PM | #8 |
Drives: 2013 Camaro 1LE Join Date: Jul 2012
Location: Verona, WI
Posts: 1,930
|
No kidding. If I got a Z/28 belly pan it would be the only "Flat" belly I've ever had!!
__________________
|
12-12-2014, 09:52 PM | #9 | |
Drives: 2013 Camaro 1LE Join Date: Jul 2012
Location: Verona, WI
Posts: 1,930
|
Quote:
__________________
|
|
12-14-2014, 06:44 PM | #10 |
Drives: '14 1LE Join Date: Nov 2013
Location: NJ
Posts: 2,436
|
Installed the Z/28 pan this weekend
|
12-14-2014, 09:55 PM | #11 |
Drives: ‘13 1LE Join Date: Jul 2013
Location: Earth
Posts: 3,904
|
Nice!
|
12-14-2014, 11:19 PM | #12 |
Drives: 2010 2SS/RS Join Date: Dec 2009
Location: Clarksville Tennesse.
Posts: 6,089
|
NICE
Very cool!!! Any special notes you would like to share??? Do you think this will work on a 10 thru 13???
|
12-15-2014, 01:20 PM | #13 |
Drives: 2019 Chevy Equinox Premier AWD Join Date: Mar 2011
Location: Silicon Valley, CA
Posts: 1,344
|
I'm also thinking there was a reason the engineers left the belly pans off of our cars. Whether it was cooling or another reason. Does anyone know if the Z/28 pan will fit a 2013 1LE?
__________________
2013 AGM 1SS/1LE, NPP, Camera
(1 of 43) |
12-15-2014, 02:20 PM | #14 | ||
Drives: 14 1LE Join Date: Mar 2013
Location: Spokane, WA
Posts: 1,567
|
Quote:
Quote:
__________________
LMS Engineering
|
||
|
|
|
|