05-09-2014, 11:23 AM | #1 |
2014 2SS, RS, 1LE Yellow
|
Location of Hash Marks
I should have my Yellow 1LE any day now. The status changed to Shipped/En Route on 4/29. I just received my hash marks and would like some direction on where to properly place them. Thanks in advance and will post pics once in my possession.
|
05-09-2014, 11:27 AM | #2 |
COTW 5/06/2013
Drives: 2017 Corvette Grand Sport-Ho-Vette Join Date: May 2012
Location: Milford, Michigan
Posts: 3,201
|
Since its draft time....
__________________
2017 Grand Sport, Borla X Pipe.....Enough Said
|
05-09-2014, 12:11 PM | #3 |
Destroyed by flooding
Drives: Wife's car Join Date: Mar 2014
Location: Louisiana
Posts: 4,673
|
Well more sunshine on the way!!!!
|
05-09-2014, 12:18 PM | #4 |
Drives: 2015commemorative vert 2SS Join Date: Oct 2013
Location: northern Indiana
Posts: 948
|
Just eyeballed it
Mine came with no instructions at all. Found some info online on utube. I put mine like 6" behind the fender break line, on the top. I tried both wet, and dry application formats.
__________________
2018 ZL1 Bright Yellow, A10, PDR, sunroof, carbon hood, and dash- sold
2020 2SS A10 sunroof..shock and steel special-traded 2015 commemorative vert 2ss |
05-09-2014, 01:17 PM | #5 |
SoCal Mayhem
Drives: 2010 Camaro 1SS/RS Join Date: Aug 2008
Location: Foothill Ranch, CA
Posts: 5,488
|
__________________
|
05-09-2014, 04:38 PM | #6 |
"Cam Only"
|
I wish I could find a nice set of these. I want them to go all the way into the wheel well like the last yellow 1LE (sengli) posted above.
But I wish they were a little bit wider/thicker of lines..
__________________
2013 AGM Camaro 2SS/RS M6 | LSA Blower, 2.5" pulley, 10% lower, FIC1000's, Fore Innovations Twin Pump fuel system w/ Flex Fuel, CMS Custom Grind Cam, Kooks 1 7/8" headers w/ catless off-road pipes, NPP Exhaust, 3.91's, JLT ZL1 Intake, Prospeed Heat Exchanger | Pfadt Suspension, 1LE Sway Bars | DSS 1000hp axles |
Tuned by Ryne @ CMS E85: 734rwhp/636rwtq (mustang dyno) |
05-09-2014, 05:00 PM | #7 |
Drives: 2012 Camaro SS 45th Anniversary Join Date: Sep 2013
Location: Albuquerque
Posts: 963
|
hard to see with the carbon metallic paint and carbon fiber hashmarks... but they go all the way wrapped into the wheel well
__________________
~ 2012 SS ~ |
05-09-2014, 05:02 PM | #8 |
Drives: 2014 Red Hot 2SS/RS/1LE NPP Recaros Join Date: Sep 2010
Location: Bay Area
Posts: 323
|
Who did you buy your hash marks from? I'm sure if you reach to your vendor they can provide you with some guidance on the install process of there particular hash marks.
Sent from my iPad using Tapatalk |
05-09-2014, 05:54 PM | #9 |
Drives: 1969 Z28, 1982 Z28, 2014 SS/RS/1LE Join Date: Nov 2013
Location: Michigan
Posts: 886
|
Hope you are right on the shipment! My car was built on 4/28 and ales went to in-transit on 4/29. Called yesterday....still sitting at the damn plant waiting for pick up!!! Said shortage of rail cars. I am not happy!
|
05-09-2014, 06:39 PM | #10 |
This is where I put mine... just estimated the location based on pictures I've seen here.
__________________
Clear Bra, Tint, Splash Guards, Ceramic Coating, Painted Spoiler and Rear Views
|
|
05-09-2014, 07:06 PM | #11 |
Drives: '11 VR 2LT HHr Join Date: May 2011
Location: Gateway to the West
Posts: 2,721
|
I know my car isnt a 1LE , but i have the hash marks too.
I got mine from PartsForYourCar a vendor here and the placement was pretty much set by the way they were cut. I put mine on wet with a little soapy water. Different angle
__________________
2011 Hhr
Formerly known as Silver85IrocZ !! |
05-09-2014, 07:14 PM | #12 |
Always Workin
Drives: 2021 Mazda MX-5 Join Date: Aug 2013
Location: Youngstown, OH
Posts: 1,362
|
The directions from bigworm say 2.75" from the front of the fender where it meets the bumper. This gives their marks a stopping point of that straight line above the wheel.
__________________
2023 Vivid Orange 1SS 1LE 6MT
Arrived 8/31 Purchased 9/3 2018 1SS 1LE, HyperBlue Metallic (Sold) 2014 1SS 1LE, Black, Twin Turbo (Sold) |
05-09-2014, 07:47 PM | #13 | |
Belle Isle
|
Quote:
Hashmarks look great on these. Just keep in mind the ones from bigwormgraphics are placed at the mark that's about 2inches above the wheel well, like in the pic below
__________________
2014 2SS
Credit to xVengeancex28 |
|
05-09-2014, 08:43 PM | #14 |
Where can I buy the hash marks ?
|
|
|
|
|
|