Rotary SPOA10 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

Kman13RSSS · 04-05-2022, 09:13 PM

Hi, I’m in need of some dimensions that I just can’t seem to find. I am looking for the outside of post to outside of post dimension. I have overall, drive through,etc but need that 1 to figure out placement of carrier beams in the ceiling. I’m hoping to have the lift post come next to the beam as opposed to under to save on ceiling height. Sooner I can figure this out the sooner I can order steel beams. Thanks

1911 1LE · 04-06-2022, 09:26 AM

I just measured mine at eye level. 128 1/4" I would make it a little wider span, just in case. BTW, mine is 138" over all at the base plates. Hope this helps

Kman13RSSS · 04-06-2022, 12:58 PM

Thank you. That helps a ton. I’ll have to double check but I believe that gives me plenty of room to set it inside the beam instead of under. How do you like the lift?

1911 1LE · 04-06-2022, 03:43 PM

Love it! So do all my friends and family. I didn't hard wire mine. I used a RV extension cord and plug it into my 220v welder plug close by.

Kman13RSSS · 04-06-2022, 07:19 PM

That’s good to hear. I miss having a garage with a lift. Hopefully lumber prices start dropping so I can start framing. It looks like you’ve got good tastes, Camaros and guns. I love the 1911’s. Best looking gun out there. I guess my collection of a dozen or so speaks to that.

04-05-2022, 09:13 PM	#1
Kman13RSSS Drives: 2013 IOM 2SS/RS 2.9 Whipple Join Date: Sep 2013 Location: Auburn NH Posts: 64	Rotary SPOA10 Hi, I’m in need of some dimensions that I just can’t seem to find. I am looking for the outside of post to outside of post dimension. I have overall, drive through,etc but need that 1 to figure out placement of carrier beams in the ceiling. I’m hoping to have the lift post come next to the beam as opposed to under to save on ceiling height. Sooner I can figure this out the sooner I can order steel beams. Thanks

04-06-2022, 09:26 AM	#2
1911 1LE Drives: 2015 SW 2SS 1LE Join Date: Jan 2018 Location: 78155 Posts: 308	I just measured mine at eye level. 128 1/4" I would make it a little wider span, just in case. BTW, mine is 138" over all at the base plates. Hope this helps __________________ Maggie 2650 @ 18psi/ 75mm 10 rib/ Dual alky nozzles/ Roto-fab/ ARH 2" Lt's/ GT-12 cam/ ZL1 3.23 Conv./MGW/RPS triple carbon clutch/RSG tranny upgrage/Pedders Ex. XA w/ remote cans and a lot of other crap 897/8??@tires

04-06-2022, 03:43 PM	#4
1911 1LE Drives: 2015 SW 2SS 1LE Join Date: Jan 2018 Location: 78155 Posts: 308	Love it! So do all my friends and family. I didn't hard wire mine. I used a RV extension cord and plug it into my 220v welder plug close by. __________________ Maggie 2650 @ 18psi/ 75mm 10 rib/ Dual alky nozzles/ Roto-fab/ ARH 2" Lt's/ GT-12 cam/ ZL1 3.23 Conv./MGW/RPS triple carbon clutch/RSG tranny upgrage/Pedders Ex. XA w/ remote cans and a lot of other crap 897/8??@tires

04-06-2022, 12:58 PM	#3
Kman13RSSS Drives: 2013 IOM 2SS/RS 2.9 Whipple Join Date: Sep 2013 Location: Auburn NH Posts: 64	Thank you. That helps a ton. I’ll have to double check but I believe that gives me plenty of room to set it inside the beam instead of under. How do you like the lift?

04-06-2022, 07:19 PM	#5
Kman13RSSS Drives: 2013 IOM 2SS/RS 2.9 Whipple Join Date: Sep 2013 Location: Auburn NH Posts: 64	That’s good to hear. I miss having a garage with a lift. Hopefully lumber prices start dropping so I can start framing. It looks like you’ve got good tastes, Camaros and guns. I love the 1911’s. Best looking gun out there. I guess my collection of a dozen or so speaks to that.