Will 20x10 ET23 wheels fit - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

LS3_JC · 08-02-2020, 08:09 PM

So I’ve been looking to buy a new set of wheels and found the factory reproductions 27 (z28 replicas), there are 2 options for offset: +35 and +23. I’m trying to make the wheels go flush with the fender. If it helps My car is a 2012 Camaro SS with the stock Brembos, stock Suspension (gonna go with coilovers) soon). Also the full specs for the wheels are: 20x10 ,ET+23 ,5x120.65 ,66.9. Same for the other ones except it’s a +35 offset.

Athletics101 · 08-02-2020, 10:20 PM

20x10 +35 can fit on all 4 corners, tho I haven’t done it. It’s a size guys run with the TSW’s. I know certainly that a 10 inch wide wheel with 35mm offset sits flush in the rear as that’s my current set up on my radials.

LS3_JC · 08-02-2020, 10:40 PM

Also will the 5x120.65 bolt pattern fit?

Athletics101 · 08-02-2020, 11:13 PM

Quote:

Originally Posted by LS3_JC

Also will the 5x120.65 bolt pattern fit?

Absolutely.

Vegas Bound · 08-02-2020, 11:22 PM

0.65 is 26/1000 of an inch.

steakmaker · 08-03-2020, 07:34 AM

I had a square set 20x10 +34 no problem,until they got stolen that is!

SSkat · 08-12-2020, 04:19 PM

I ran a 20x10 +25 squared with 275/315 tires and it fit fine with no spacers or anything. It poked a little but not much. I liked it better in the rear more than my current 20x11 +43.

SSEssence · 08-12-2020, 05:20 PM

I'm running 20x10 +25 up front w no issues or rubbing.

jksynergy · 09-14-2020, 09:18 PM

Yes, they will fit.
Both of these sets are 20x10. Gray wheels are et +35. The polished and brushed set is et +20. The bolt pattern you are looking at is for a Corvette but I believe it may not fit the Camaro also. No promises though.

Sent from my SM-T377T using Tapatalk

flht99b · 09-15-2020, 05:37 AM

Quote:

Originally Posted by Athletics101

Absolutely.

Do not use 5x120.65mm bolt circle wheels on a 5th gen Camaro. You will stress the studs and not tighten the wheel correctly. Correct bolt circle is 5x120mm. 5x120.65mm bolt circle is the old small Chevy 4.75x5 bolt circle.

Deputy347k9 · 09-15-2020, 06:03 AM

Choose Chevrolet Camaro model with 5X120.65 PCD
Chevrolet Camaro models that are suitable for a 5X120.65 bolt pattern.

Search by Chevrolet Camaro modification
search
Camaro 3.8 IV Restyling (1998-2002)
Camaro 5.7 IV Restyling (1998-2002)
Camaro 5.7 SS IV Restyling (1998-2002)
Camaro 3.4 IV (1993-1995)
Camaro 5.7 IV (1993-1997)
Camaro 3.8 IV (1995-1997)
Camaro 5.7 SS IV (1996-1997)
Camaro All trims III (1982-1992)
Camaro All trims II (1970-1981)
Camaro All trims I (1967-1969)

This spacing will fit many other Chevrolet models, however all are early models, some going back to 1955!

As just previously stated, "stay away from them unless you want trouble", they might go on but they might also cause serious and dangerous damage.

SSammy · 09-15-2020, 07:18 AM

Mine are 20x10 +35 MRR228 with 275/40zr20 all 4 corners. Originally installed at stock height and now on 1” BMR drop springs. No problems or rubbing either way.

Avenging Orange · 09-15-2020, 10:27 AM

The offsets are correct for stock stagger. +35 rear and +23 front for a 10" wheel....which should put them flush.
I have 20x9 square at +30 and added 5mm spacer to the fronts to get them to a +25. Both fit perfectly flush with the fender. If you are still confused, call one of our wheel sponsors. I talked at length with Akio @ PK Auto Design, he really helped me understand offsets and back spacing and how it applied to different wheel widths.

08-02-2020, 08:09 PM	#1
LS3_JC Drives: 12’ Chevy camaro SS 6MT Join Date: Jul 2020 Location: Florida Posts: 9	Will 20x10 ET23 wheels fit So I’ve been looking to buy a new set of wheels and found the factory reproductions 27 (z28 replicas), there are 2 options for offset: +35 and +23. I’m trying to make the wheels go flush with the fender. If it helps My car is a 2012 Camaro SS with the stock Brembos, stock Suspension (gonna go with coilovers) soon). Also the full specs for the wheels are: 20x10 ,ET+23 ,5x120.65 ,66.9. Same for the other ones except it’s a +35 offset.

08-02-2020, 10:20 PM	#2
Athletics101 Drives: 5th Gen L99 Join Date: Nov 2017 Location: Lake Havasu City Posts: 244	20x10 +35 can fit on all 4 corners, tho I haven’t done it. It’s a size guys run with the TSW’s. I know certainly that a 10 inch wide wheel with 35mm offset sits flush in the rear as that’s my current set up on my radials. __________________ LSA conversion 2.5 upper 10% lower, L99 converted to LS3. TSP 229/244 cam, TSP LS3 ported and milled heads milled .015,Kooks LT’s no cats, Roto Fab, Borla arak cat back. 3200 stall,Forgestar F14 18’s and drag radials, pedders coil overs, BMR trailing arms & adjustable toe rods, mildly stripped Interior 685/613 on E 610/571 on 91 Last edited by Athletics101; 08-02-2020 at 11:06 PM.

08-12-2020, 05:20 PM	#8
SSEssence Instagram: Sangstah Drives: 2019 Camaro 1LE Join Date: Sep 2016 Location: Buena Park, CA. Posts: 2,802 View My Garage	I'm running 20x10 +25 up front w no issues or rubbing. __________________ 2019 SS 1LE - "CaSSandra" 2014 SS - "AleSSandra - Sold" 94 Z28 - Sold Follow the build https://www.camaro6.com/forums/showthread.php?t=612717

09-14-2020, 09:18 PM	#9
jksynergy Drives: 11 SW SYNERGY SERIES/14 1SS 1LE Join Date: May 2012 Location: Missouri Posts: 1,223	Yes, they will fit. Both of these sets are 20x10. Gray wheels are et +35. The polished and brushed set is et +20. The bolt pattern you are looking at is for a Corvette but I believe it may not fit the Camaro also. No promises though. Sent from my SM-T377T using Tapatalk __________________ 2011 Summit White Synergy Series Edition, the hot innocent woman named Ava that we show off around town, dressed in white complete with angel's wings. Sold, but never forgotten. 2014 1SS 1LE. Bama, sporting Red Rock Metallic demon's horns, when we are ready to get naughty and open a can of whoopass! Airaid, Spectre, Xpel,Bowler shifter Peddars, UMI, Ult Perf. Diode Dynamics, JRE Tune, XS Power battery, Hooker Headers Blackheart exhaust,Powerbrake InstaGram & Twitter: @jlouie62 FB: hangtimeracing Last edited by jksynergy; 09-15-2020 at 01:02 PM.

09-15-2020, 06:03 AM	#11
Deputy347k9 Drives: 2014 Ashen Gray Convertible Join Date: Apr 2017 Location: Havelock, NC Posts: 1,328	Choose Chevrolet Camaro model with 5X120.65 PCD Chevrolet Camaro models that are suitable for a 5X120.65 bolt pattern. Search by Chevrolet Camaro modification search Camaro 3.8 IV Restyling (1998-2002) Camaro 5.7 IV Restyling (1998-2002) Camaro 5.7 SS IV Restyling (1998-2002) Camaro 3.4 IV (1993-1995) Camaro 5.7 IV (1993-1997) Camaro 3.8 IV (1995-1997) Camaro 5.7 SS IV (1996-1997) Camaro All trims III (1982-1992) Camaro All trims II (1970-1981) Camaro All trims I (1967-1969) This spacing will fit many other Chevrolet models, however all are early models, some going back to 1955! As just previously stated, "stay away from them unless you want trouble", they might go on but they might also cause serious and dangerous damage. __________________

08-02-2020, 10:40 PM	#3
LS3_JC Drives: 12’ Chevy camaro SS 6MT Join Date: Jul 2020 Location: Florida Posts: 9	Also will the 5x120.65 bolt pattern fit?

08-02-2020, 11:22 PM	#5
Vegas Bound Account Suspended Drives: 2013 Sparkly Red One Join Date: Dec 2018 Location: Hospitality State Posts: 2,558	0.65 is 26/1000 of an inch.

08-03-2020, 07:34 AM	#6
steakmaker Drives: '10 Camaro SS,Jeep Commander Hemi Join Date: Mar 2010 Location: Cicero,NY Posts: 567	I had a square set 20x10 +34 no problem,until they got stolen that is!

08-12-2020, 04:19 PM	#7
SSkat Drives: 2010 Camaro 2SS Join Date: Mar 2018 Location: Pensacola, FL Posts: 268	I ran a 20x10 +25 squared with 275/315 tires and it fit fine with no spacers or anything. It poked a little but not much. I liked it better in the rear more than my current 20x11 +43.

09-15-2020, 07:18 AM	#12
SSammy Drives: 2015 2SS A6 Commemorative Edition Join Date: Nov 2019 Location: Utah Posts: 433 View My Garage	Mine are 20x10 +35 MRR228 with 275/40zr20 all 4 corners. Originally installed at stock height and now on 1” BMR drop springs. No problems or rubbing either way.

09-15-2020, 10:27 AM	#13
Avenging Orange Drives: 2010 Inferno Orange 2SS/RS Join Date: Apr 2010 Location: Clermont, IN Posts: 3,297	The offsets are correct for stock stagger. +35 rear and +23 front for a 10" wheel....which should put them flush. I have 20x9 square at +30 and added 5mm spacer to the fronts to get them to a +25. Both fit perfectly flush with the fender. If you are still confused, call one of our wheel sponsors. I talked at length with Akio @ PK Auto Design, he really helped me understand offsets and back spacing and how it applied to different wheel widths. __________________ 2010 Inferno Orange 2SS/RS M6 Black Leather, Sun Roof, OBX Headers, Borla touring axle back, Cold Air Inductions CAI , non synthetic fluids, BMR total bushing upgrade/1" lowering springs, DSE 32mm rear sway bar. GM fe4 shocks/struts/LCA's, AAM 3.91 diff, Vertini RFS1.8 20x9 +30. Conti ExtremeContact Sport 275/35/20. sjm autoprod ABL dash kit. Mike Norris tuned 413/419. Avenging Orange: 43 years of not buying into the Hype........and damn proud of it!! https://youtu.be/9JD9it6SmB8 https://youtu.be/xmelTlEzI34 KICKING CANCERS ASS SINCE 2015!!