12-16-2018, 06:49 PM | #1 |
Drives: 2011 Camaro SS convertible Join Date: Oct 2018
Location: Cleveland
Posts: 8
|
MyLink faceplate poor fit
I have a 2011 Camaro and just did the MyLink Nav upgrade. Upon installing the faceplate, I notice I can't get the screen to lock tightly in place and have a gap around mostly the top between the radio and the dash. The fit on the passenger side is worse. Is there something I'm not doing correctly?
|
12-16-2018, 07:14 PM | #2 | |
Drives: 2012 Camaro 45th Anniversary RS Join Date: Nov 2012
Location: New York
Posts: 2,418
|
Quote:
So I have not installed this unit, but I just did an aftermarket radio install using the pac kit. I found that getting everything to fit behind the radio was a challenge. Had I known that the space was so limited, I would have installed a multimedia radio (much more shallow than a regular double din with a CD drive). Do you think you could get some of the wiring back tighter? |
|
12-16-2018, 07:31 PM | #3 |
'It's an experiment'
Drives: [COTW 2/09/15] '11 GPI LSA SC Z/LE Join Date: May 2014
Location: Dallas TX
Posts: 8,694
|
Did you trim the top 2 guides/supports on top of the mylink that were used by the old style radio?
https://www.camaro5.com/forums/showp...5&postcount=57 Also you should have trimmed the rear area also (see where I have blue tape). Had to trim the gauges/pod area to fit correctly... Did you buy Gen5Diy’s kit? -Don
__________________
747 RWHP 794 RWTQ
"Horsepower sells cars, torque wins races." - Enzo Ferrari See My Build: http://www.camaro5.com/forums/showthread.php?t=385577 |
12-16-2018, 10:40 PM | #4 |
Drives: 2011 Camaro SS convertible Join Date: Oct 2018
Location: Cleveland
Posts: 8
|
I have the upper supports and the receiver fits fine. I did trim the back too. Does the bottom go in first (by the 2 bolts) and then swings up to snap in?
|
12-19-2018, 03:24 AM | #5 |
Drives: 2011 Camaro SS convertible Join Date: Oct 2018
Location: Cleveland
Posts: 8
|
So spoke with Gen5DIY and had to remove my center console (again) for the faceplate to fit well. Really like this upgrade!
|
12-19-2018, 09:01 PM | #6 |
Drives: 2011 2SS/RS Join Date: Feb 2016
Location: Jacksonville FL
Posts: 1,190
|
you dont have the bottom properly inserted. remove and reinsert and adjust
__________________
•2011 Camaro SS 2SS/RS A6
•MRR M017 1le Replica Wheels •Vararam Ram Air Intake •Speed Engineering Longtube Headers w/ Magnaflow HF Cats •Bo White PnP Stage 2 TB •GPI SS2 VVT Cam w Cometic thin gaskets 10.69 compression •Xpipe w/ Res Delete and NPP Exhaust •Tuned By Anonymous Calibrations •Gen5DIY Mylink Conversion W/ Backup Cam •Morel 3 way custom speakers, Infinity 860w Subwoofers in trunk baffle •Helix P6 6ch amp w/ 8ch DSP and P1 Sub amp |
12-20-2018, 12:30 PM | #7 |
Drives: Camaro Join Date: Oct 2018
Location: Alabama
Posts: 673
|
Looks like you fixed it but I had the same issue when I did the install. Eventually I took a break and came back and it popped in.
|
12-21-2018, 10:08 AM | #8 | |
Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008
Location: By the lake in AZ
Posts: 15,719
|
Quote:
|
|
12-24-2018, 10:12 PM | #9 |
Drives: nice Join Date: Dec 2018
Location: newyork
Posts: 1
|
nice to know the tips on how to fix from the experts and appreciate their efforts
__________________
|
|
|
|
|