01-03-2019, 05:34 PM | #1 |
Drives: 2018 Chevrolet Camaro 2SS 1LE Join Date: Jul 2017
Location: Jacksonville
Posts: 153
|
SS 1LE Rear Spoiler
Im curious if there are any aftermarket Rear Spoilers that can replace the 1LE Rear Spoiler and match up to the same mounting holes?
|
01-03-2019, 07:46 PM | #2 |
Drives: 2018 Hyper Blue 1SS 1LE Join Date: Jul 2011
Location: Brownsburg, Indiana
Posts: 6,231
|
the 1LE rear spoiler is held down by double sided tape not sure if there are holes. You could go with the ZL1/1LE spoiler
__________________
Ryan
* 2018 1SS 1LE Camaro Hyper Blue Metallic Car Build: http://www.camaro6.com/forums/showth...0#post10049680 |
01-03-2019, 08:16 PM | #3 |
Drives: 2018 Camaro 1SS/1LE Join Date: Feb 2015
Location: Port Saint Lucie FL
Posts: 1,224
|
|
01-03-2019, 09:35 PM | #4 | |
|
Quote:
https://www.ebay.com/itm/1LE-Extende...L/323496840212 |
|
01-03-2019, 09:56 PM | #5 |
Drives: 2018 Chevrolet Camaro 2SS 1LE Join Date: Jul 2017
Location: Jacksonville
Posts: 153
|
|
01-03-2019, 09:56 PM | #6 |
Drives: 2018 Chevrolet Camaro 2SS 1LE Join Date: Jul 2017
Location: Jacksonville
Posts: 153
|
|
01-03-2019, 10:30 PM | #7 |
Drives: 2018 Hyper Blue 1SS 1LE Join Date: Jul 2011
Location: Brownsburg, Indiana
Posts: 6,231
|
__________________
Ryan
* 2018 1SS 1LE Camaro Hyper Blue Metallic Car Build: http://www.camaro6.com/forums/showth...0#post10049680 |
01-04-2019, 12:35 PM | #8 |
Drives: 2018 ss 1le Join Date: Jan 2019
Location: Seattle
Posts: 5
|
|
01-04-2019, 02:30 PM | #9 | |
Drives: 2017 1SS 1LE Join Date: Jun 2016
Location: Detroit, MI
Posts: 1,001
|
Quote:
There are 9 holes in the SS 1LE decklid for the OE spoiler: 3 for threaded studs on the LH side, 3 slots for clips in the middle, and 3 more threaded stud holes on the RH side. Only 2 of the existing 9 holes will line up (the middle threaded stud hole on each side). The others would need to be sealed somehow and then you'd have 4 more holes to punch out. Here's a crappy drawing that gives a rough representation of how it's laid out. Black are existing holes in the SS 1LE decklid and green are the ZL1 1LE mounting locations.
__________________
2017 SS 1LE.
|
|
01-04-2019, 05:05 PM | #10 |
|
Since the holes in the 1LE trunk are different than the SS & ZL1 trunk, you need a donor trunk or have to drill extra holes and fill/cover some others. The donor or new trunk should be from a 2017 (or later) SS or ZL1 since they have the extra reinforcement same as the ZLE trunk if you want to use the wing. I have also heard the trunk support rods are different to support the extra weight of the big wing.
|
01-04-2019, 05:07 PM | #11 | |
|
Quote:
|
|
01-04-2019, 08:21 PM | #12 |
Drives: 2018 Chevrolet Camaro 2SS 1LE Join Date: Jul 2017
Location: Jacksonville
Posts: 153
|
|
01-04-2019, 10:20 PM | #13 |
|
This one looks like it's actually made for the 1LE
https://extremeonlinestore.com/colle...12590246625381 |
|
|
Post Reply
|
|
|