07-04-2013, 09:20 AM | #29 |
Drives: 11 Seconds or Faster Join Date: May 2012
Location: Arvada, Colorado
Posts: 2,797
|
I trailer mine everywhere, and I have mine lowered A LOT. Getting in and out of an enclosed trailer can be done two ways: go through the trunk; or crawl through the window. Window is easier, I just take my shoes off. Some trailers have escape doors on the side so you can get out, but you can do it pretty easily without one. Also, if you haven't trailered a car before, remember to leave the car in neutral and the parking brake off. |
07-08-2013, 04:34 PM | #30 |
Perma Grinning
Drives: 2012 Tom Henry Racing ZL1 Join Date: Feb 2012
Location: Schaumburg, IL
Posts: 452
|
|
07-11-2013, 06:29 AM | #31 | |
Drives: 2011 Camaro LS Stripper model Join Date: Feb 2011
Location: South Beloit IL
Posts: 641
|
Quote:
1 load car in or on trailer leave in neutral set parking brake 2 hook all for corners and snug straps 3 remove parking brake 4 tighten straps 5 set parking brake 6 put in park or gear. Seting the parking brake after tieing down will cause no harm to the car what so ever. This is how the manufactures transport them!!!! I know people disagree with cluster hooks and tieing down from the frame as I recomend but at least set the e brake. Please don't belive everything you read talk to an old auto transporter. Someone who's been doing it for 30 years. Thats who taught me and we probably tied down over a thousand cars together helping him load. |
|
07-12-2013, 08:53 AM | #32 | |
Perma Grinning
Drives: 2012 Tom Henry Racing ZL1 Join Date: Feb 2012
Location: Schaumburg, IL
Posts: 452
|
Quote:
Use "J" hooks and tie the car down by the frame. I also criss cross the straps, which is to prevent the car from moving side to side in an "situation" . . . |
|
07-12-2013, 09:05 AM | #33 |
Boosted Moderator
|
I can only speak for my open trailer, but even with the 5200 lbs axles and bigger wheel/tires, and lowered car, my doors open over the top of the fenders. I ordered it with removable fenders as SSS mentioned, but have never taken them off....
__________________
If the car feels like it is on rails, you are probably driving too slow. -Ross Bentley
Horsepower is how fast you hit the wall. Torque is how far you take the wall with you. “If everything seems under control, you're just not going fast enough.” Mario Andretti If you can turn, you ain't going fast enough... |
07-12-2013, 10:50 AM | #34 |
Perma Grinning
Drives: 2012 Tom Henry Racing ZL1 Join Date: Feb 2012
Location: Schaumburg, IL
Posts: 452
|
|
07-13-2013, 11:41 AM | #35 |
Drives: 11 Seconds or Faster Join Date: May 2012
Location: Arvada, Colorado
Posts: 2,797
|
When you have a fully finished trailer with flooring you'll know what I mean, if you leave it in gear or with the brake on it takes the floor up. The straps keep the car from going anywhere. Not to mention the stress on the drivetrain from knocking on the tranny.
|
07-13-2013, 03:57 PM | #36 | |
Seeking 9s on M6...
Drives: 2012 2SS/RS LS3 aka "BlackWidow" Join Date: May 2012
Location: Houston, TX
Posts: 397
|
Quote:
I'm planning to trailer w parking brake engaged. I can understand not outing in gear.
__________________
|
|
07-15-2013, 02:38 PM | #37 | |
Drives: 2011 Camaro LS Stripper model Join Date: Feb 2011
Location: South Beloit IL
Posts: 641
|
Quote:
Correctly secured that car shouldn't ever budge a fraction of an inch. Now if you went to pull out and the rubber coin flooring stuck to the tires that would be a culprit of traction compound or hot tires sticking to the rubber coin floor. I always recomend the drag racers to carpet the four contact points under the tires to prevent this. Due to vht at the track. I have seen this in a customers trailer. Wrecked the whole damn floor when he pulled out it came with and had to cut it off his tires. |
|
07-15-2013, 07:14 PM | #38 |
Drives: 11 Seconds or Faster Join Date: May 2012
Location: Arvada, Colorado
Posts: 2,797
|
Well that's how we've always trailered cars, haven't had an issue yet. Top fuel teams but their rigs from the place I buy my trailers, and that's how I was taught. It's easier on the car, driveline, and trailer.
|
07-15-2013, 08:12 PM | #39 |
Drives: 2011 Camaro LS Stripper model Join Date: Feb 2011
Location: South Beloit IL
Posts: 641
|
For those buying trailers you can typicaly spec a specific deck height and dove tail length.
On the open car haulers you would want something with a 4' dovetail and 5-6' ramps. Then adjust deck height with the start angle of the torsion axle. Typical start angle with a torsion axle option would 10 degrees up. I like to start them at zero or 10 degrees down for the low profile cars like ours which would bring the deck up higher than normal in comparison to the top of the fender. No removable fenders required this way. Sure you end up with the car higher in the air when traveling but were only talki g 4 inches roughly. Same goes for the enclosed trailers. Most enclosed trailers come standard with a 4" drop axle. Many cars even with an escape door can't clear the inner fender to open the door. When running spring axles spec a straight tube no drop. This lowers the fender 4" combine this with an escape door and even the lowest car door typicaly opens over the fender and out the door. This can again also be done with changing the start angle of a torsion axle. Enclosed trailers typical have other higher cost options like the drive over ramps shown above by thr zl1 #1. Factory option like shown gets pricy but they can also be home built and perform very well. If you trailer dealer or manufacture isn't interested in playing with these options keep shopping. Lol |
07-30-2013, 12:56 AM | #40 |
Seeking 9s on M6...
Drives: 2012 2SS/RS LS3 aka "BlackWidow" Join Date: May 2012
Location: Houston, TX
Posts: 397
|
This may be thread jacking, but felt it blended with the discussion. I trailered my car for the first time out of necessity this weekend...damn water pump pulley. Must admit it was nerve racking every bumb I hit at 90 miles an hour (kidding about speed, but it was nerve racking).
Anyway I tied down crossed from the rear Lower control arms, then in the front I was looking for somewhere farther back to cross and still hold from rolling back. I used the hole in frame just beyond front tired...looks like a jack point for a lift...doesn't feel like the thickest part on the frame, but it seemed to hold. Are these good places? Or are ther better? I tried to include some close ups, but damn phone names them all the same.
__________________
|
|
|
|
|