ADM PERFORMANCE DOES CUSTOM AEROFORCE INTERCEPTOR INSTALL ON CAMARO - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

ADM PERFORMANCE · 06-03-2009, 06:52 PM

ADM Performance specializes in custom manufacturing performance parts for Gm vehicles,we also specialize in custom installs.With over 25 years of design and integration we go the extra mile when it comes to true OEM quality installs.

Recently there has been growing concern on where to put any aftermarket gauges in the 2010 Camaro.With this concern we took it upon ourselves to create the first integrated gauge/gauges into the dash of the Camaro.

We took a product we have been selling for several years now,it's called the Aeroforce Interceptor .

The Interceptor scan gauge is capable of displaying over 100 parameters, two at a time (8 using cyclic scan), at an adjustable rate of up to approximately 20 times per second. Not all are supported by every vehicle, so there is no guarantee that the Interceptor will display all of these on your particular car or truck. If the vehicle is broadcasting the parameter, the Interceptor will recognize this and make it available for display. A sample list is below...
RPM
MPH
Intake Air Temperature (post Intercooler)
Ambient Air Temperature (pre Intercooler)
Engine Coolant Temperature
Exhaust Gas Temperature (PCM Calculated)
Transmission Temp. (auto trans)
Manifold Pressure (vacuum/boost) displayed in PSI
Fuel Temperature
Battery Voltage
Battery Temp
Injector Pulse Width in msec.
Injector Duty Cycle (%)
Air Flow Rate into engine
Long Term Fuel Trim
Short Term Fuel Trim
O2 Sensor Voltage
Barometric Pressure
Ignition Advance
Base Spark
PCM Spark Adjust
Fuel Status (open/closed loop)
Wastegate Solenoid Duty Cycle (%)
Knock Retard
Knock Sensor Raw Voltage
Throttle Position Percentage
Throttle Position Sensor Raw Volts
Calculated Net Horsepower
Engine Load
Transmission Slip
Current Transmission Gear
Torque Delivered to Transmission
Torque Converter lockup status
Brake pressure
Brake Booster Travel
Steering Angle
Non-driven Wheel Speed
Lateral G's
Yaw
Fuel economy (instantaneous and average)
P-ratio - pressure ratio MAP/Barometer
2 user configurable analog inputs**
** 0-5v inputs can be configured to read the outputs from MAP sensors, Air/Fuel ratio kits, pressure or temperature sensors, etc. Raw voltage can be displayed or a conversion can be entered to read proper units.

Users will find that ability to log RPM vs other parameters at high speed such as ignition advance, boost, or knock retard invaluable with regards to tuning.

ADM Performance stocks many different color combinations of the Interceptor,But my favorite is the one pictured.

Andy
www.admperformance.com
214-228-8782
Mon-thur - 9:30-3:30

redd214 · 06-03-2009, 07:37 PM

damn that looks clean!! more pics more pics!!!

Shocker · 06-03-2009, 08:09 PM

sweet install

franknbeans · 06-03-2009, 08:25 PM

I had one of these gauges in my SRT4... best company and gauge to get hands down.

ADM PERFORMANCE · 06-03-2009, 08:39 PM

http://www.aeroforcetech.com/action.html

ADM Performance specializes in custom manufacturing performance parts for Gm vehicles,we also specialize in custom installs.With over 25 years of design and integration we go the extra mile when it comes to true OEM quality installs.

Recently there has been growing concern on where to put any aftermarket gauges in the 2010 Camaro.With this concern we took it upon ourselves to create the first integrated gauge/gauges into the dash of the Camaro.

We took a product we have been selling for several years now,it's called the Aeroforce Interceptor .

The Interceptor scan gauge is capable of displaying over 100 parameters, two at a time (8 using cyclic scan), at an adjustable rate of up to approximately 20 times per second. Not all are supported by every vehicle, so there is no guarantee that the Interceptor will display all of these on your particular car or truck. If the vehicle is broadcasting the parameter, the Interceptor will recognize this and make it available for display. A sample list is below...
RPM
MPH
Intake Air Temperature (post Intercooler)
Ambient Air Temperature (pre Intercooler)
Engine Coolant Temperature
Exhaust Gas Temperature (PCM Calculated)
Transmission Temp. (auto trans)
Manifold Pressure (vacuum/boost) displayed in PSI
Fuel Temperature
Battery Voltage
Battery Temp
Injector Pulse Width in msec.
Injector Duty Cycle (%)
Air Flow Rate into engine
Long Term Fuel Trim
Short Term Fuel Trim
O2 Sensor Voltage
Barometric Pressure
Ignition Advance
Base Spark
PCM Spark Adjust
Fuel Status (open/closed loop)
Wastegate Solenoid Duty Cycle (%)
Knock Retard
Knock Sensor Raw Voltage
Throttle Position Percentage
Throttle Position Sensor Raw Volts
Calculated Net Horsepower
Engine Load
Transmission Slip
Current Transmission Gear
Torque Delivered to Transmission
Torque Converter lockup status
Brake pressure
Brake Booster Travel
Steering Angle
Non-driven Wheel Speed
Lateral G's
Yaw
Fuel economy (instantaneous and average)
P-ratio - pressure ratio MAP/Barometer
2 user configurable analog inputs**
** 0-5v inputs can be configured to read the outputs from MAP sensors, Air/Fuel ratio kits, pressure or temperature sensors, etc. Raw voltage can be displayed or a conversion can be entered to read proper units.

Users will find that ability to log RPM vs other parameters at high speed such as ignition advance, boost, or knock retard invaluable with regards to tuning.

ADM Performance stocks many different color combinations of the Interceptor,But my favorite is the one pictured.

Andy
www.admperformance.com
214-228-8782
Mon-thur - 9:30-3:30

ZZcamaro · 06-03-2009, 08:41 PM

I need a price...I am interested in one for my project.

ADM PERFORMANCE · 06-03-2009, 08:48 PM

Due to the complex install we will offer this setup to ADM inhouse customers only.

I will be in contact with the manufacturer to see if we can possibly work together on having remote components for custom installs like this one.

Current price for 1 gauge is $239.00

Custom installed - Interceptor only - $759.00
Interceptor with 2 bar boost sensor - $859.00
Interceptor with wideband installed - $1299.00
Interceptor with wideband and 2 bar boost sensor - $1399.00
Dual gauges with cnc painted bezel available for additional cost.

All of the above come with cnc cut oem painted trim bezel.

Andy

blackedout010 · 06-03-2009, 10:34 PM

very nice!!

RobbRock · 06-04-2009, 01:32 AM

Nice

Morepwr · 06-04-2009, 04:13 PM

Damn! Thats one of the coolest things I have seen! What a great gauge set up that is!

optical · 06-04-2009, 04:20 PM

That looks slick! awesome!

alex33x · 06-04-2009, 04:21 PM

Nice! ADM does it again!

ssrsheaven · 06-04-2009, 04:24 PM

Nice I like where can I get mine at?

MerF · 06-04-2009, 04:26 PM

Very nice.

Can we make better thread titles though?

06-03-2009, 06:52 PM	#1
ADM PERFORMANCE Drives: Anything I want Join Date: Oct 2008 Location: DfW - Texas Posts: 5,405	ADM Performance does does aeroforce interceptor install ADM Performance specializes in custom manufacturing performance parts for Gm vehicles,we also specialize in custom installs.With over 25 years of design and integration we go the extra mile when it comes to true OEM quality installs. Recently there has been growing concern on where to put any aftermarket gauges in the 2010 Camaro.With this concern we took it upon ourselves to create the first integrated gauge/gauges into the dash of the Camaro. We took a product we have been selling for several years now,it's called the Aeroforce Interceptor . The Interceptor scan gauge is capable of displaying over 100 parameters, two at a time (8 using cyclic scan), at an adjustable rate of up to approximately 20 times per second. Not all are supported by every vehicle, so there is no guarantee that the Interceptor will display all of these on your particular car or truck. If the vehicle is broadcasting the parameter, the Interceptor will recognize this and make it available for display. A sample list is below... RPM MPH Intake Air Temperature (post Intercooler) Ambient Air Temperature (pre Intercooler) Engine Coolant Temperature Exhaust Gas Temperature (PCM Calculated) Transmission Temp. (auto trans) Manifold Pressure (vacuum/boost) displayed in PSI Fuel Temperature Battery Voltage Battery Temp Injector Pulse Width in msec. Injector Duty Cycle (%) Air Flow Rate into engine Long Term Fuel Trim Short Term Fuel Trim O2 Sensor Voltage Barometric Pressure Ignition Advance Base Spark PCM Spark Adjust Fuel Status (open/closed loop) Wastegate Solenoid Duty Cycle (%) Knock Retard Knock Sensor Raw Voltage Throttle Position Percentage Throttle Position Sensor Raw Volts Calculated Net Horsepower Engine Load Transmission Slip Current Transmission Gear Torque Delivered to Transmission Torque Converter lockup status Brake pressure Brake Booster Travel Steering Angle Non-driven Wheel Speed Lateral G's Yaw Fuel economy (instantaneous and average) P-ratio - pressure ratio MAP/Barometer 2 user configurable analog inputs 0-5v inputs can be configured to read the outputs from MAP sensors, Air/Fuel ratio kits, pressure or temperature sensors, etc. Raw voltage can be displayed or a conversion can be entered to read proper units. Users will find that ability to log RPM vs other parameters at high speed such as ignition advance, boost, or knock retard invaluable with regards to tuning. ADM Performance stocks many different color combinations of the Interceptor,But my favorite is the one pictured. Andy www.admperformance.com 214-228-8782 Mon-thur - 9:30-3:30 Last edited by ADM PERFORMANCE; 06-06-2009 at 08:53 AM.

06-03-2009, 08:09 PM	#3
Shocker Future 5th Gen Owner Drives: 2004 Pontiac GTO Join Date: May 2009 Location: Westchester,IL Posts: 34	sweet install __________________ Future Owner of a5th Gen Black/Black and more Black RS/SS For now a lightly modded 04 GTO

06-03-2009, 08:25 PM	#4
franknbeans Whipped Drives: 2010 CAMARO Join Date: Sep 2008 Location: Pittsburgh-ish - PA Posts: 4,216 View My Garage	I had one of these gauges in my SRT4... best company and gauge to get hands down. __________________ Car of the week 7/7/14

06-03-2009, 08:39 PM	#5
ADM PERFORMANCE Drives: Anything I want Join Date: Oct 2008 Location: DfW - Texas Posts: 5,405	ADM Performance -Aeroforce Interceptor 2010 Camaro http://www.aeroforcetech.com/action.html ADM Performance specializes in custom manufacturing performance parts for Gm vehicles,we also specialize in custom installs.With over 25 years of design and integration we go the extra mile when it comes to true OEM quality installs. Recently there has been growing concern on where to put any aftermarket gauges in the 2010 Camaro.With this concern we took it upon ourselves to create the first integrated gauge/gauges into the dash of the Camaro. We took a product we have been selling for several years now,it's called the Aeroforce Interceptor . The Interceptor scan gauge is capable of displaying over 100 parameters, two at a time (8 using cyclic scan), at an adjustable rate of up to approximately 20 times per second. Not all are supported by every vehicle, so there is no guarantee that the Interceptor will display all of these on your particular car or truck. If the vehicle is broadcasting the parameter, the Interceptor will recognize this and make it available for display. A sample list is below... RPM MPH Intake Air Temperature (post Intercooler) Ambient Air Temperature (pre Intercooler) Engine Coolant Temperature Exhaust Gas Temperature (PCM Calculated) Transmission Temp. (auto trans) Manifold Pressure (vacuum/boost) displayed in PSI Fuel Temperature Battery Voltage Battery Temp Injector Pulse Width in msec. Injector Duty Cycle (%) Air Flow Rate into engine Long Term Fuel Trim Short Term Fuel Trim O2 Sensor Voltage Barometric Pressure Ignition Advance Base Spark PCM Spark Adjust Fuel Status (open/closed loop) Wastegate Solenoid Duty Cycle (%) Knock Retard Knock Sensor Raw Voltage Throttle Position Percentage Throttle Position Sensor Raw Volts Calculated Net Horsepower Engine Load Transmission Slip Current Transmission Gear Torque Delivered to Transmission Torque Converter lockup status Brake pressure Brake Booster Travel Steering Angle Non-driven Wheel Speed Lateral G's Yaw Fuel economy (instantaneous and average) P-ratio - pressure ratio MAP/Barometer 2 user configurable analog inputs 0-5v inputs can be configured to read the outputs from MAP sensors, Air/Fuel ratio kits, pressure or temperature sensors, etc. Raw voltage can be displayed or a conversion can be entered to read proper units. Users will find that ability to log RPM vs other parameters at high speed such as ignition advance, boost, or knock retard invaluable with regards to tuning. ADM Performance stocks many different color combinations of the Interceptor,But my favorite is the one pictured. Andy www.admperformance.com 214-228-8782 Mon-thur - 9:30-3:30

06-03-2009, 08:48 PM	#7
ADM PERFORMANCE Drives: Anything I want Join Date: Oct 2008 Location: DfW - Texas Posts: 5,405	Interceptor price Due to the complex install we will offer this setup to ADM inhouse customers only. I will be in contact with the manufacturer to see if we can possibly work together on having remote components for custom installs like this one. Current price for 1 gauge is $239.00 Custom installed - Interceptor only - $759.00 Interceptor with 2 bar boost sensor - $859.00 Interceptor with wideband installed - $1299.00 Interceptor with wideband and 2 bar boost sensor - $1399.00 Dual gauges with cnc painted bezel available for additional cost. All of the above come with cnc cut oem painted trim bezel. Andy

06-03-2009, 07:37 PM	#2
redd214 Drives: 95 Impala SS Join Date: Mar 2008 Location: Herndon, VA Posts: 3	damn that looks clean!! more pics more pics!!!

06-03-2009, 08:41 PM	#6
ZZcamaro Drives: 2SS w/ ZZ427 Package!! Join Date: Oct 2008 Location: Pittsburgh, PA Posts: 2,700	I need a price...I am interested in one for my project.

06-03-2009, 10:34 PM	#8
blackedout010 Drives: on order black 2010 2ss Join Date: Mar 2009 Location: north carolina Posts: 913	very nice!!

06-04-2009, 01:32 AM	#9
RobbRock Consultant Camino Real Drives: 2010 2SS Camaro Join Date: Dec 2007 Location: Southern California Posts: 315 View My Garage	Nice

06-04-2009, 04:13 PM	#10
Morepwr woohoo Drives: Silverado, 70cutlass, 57chevy&more Join Date: Apr 2009 Location: Socal Posts: 558	Damn! Thats one of the coolest things I have seen! What a great gauge set up that is! __________________ I am not useless, I can still be used as a bad example!

06-04-2009, 04:20 PM	#11
optical The Pilot Drives: 1993 Chevy C1500 Ext Cab, 5.7L Join Date: Apr 2009 Location: Mesa, AZ Posts: 184 View My Garage	That looks slick! awesome! __________________ Driving: 1993 C1500 Ext Cab Truck, 5.7L, BF Goodrich All-Terrains, Named: "SexyTruck" Future Car: 2011 IOM Camaro 2SS/RS Manual, Black Stripes, Hurst Short-Throw, IO Interior!

06-04-2009, 04:21 PM	#12
alex33x Drives: 2013 Camaro ZL1 Join Date: Apr 2009 Location: El Paso, Tx Posts: 688	Nice! ADM does it again! __________________ Devliered July 20, 2012

06-04-2009, 04:24 PM	#13
ssrsheaven Drives: 92 firebird,2010 camaro Join Date: May 2009 Location: Indianapolis,In Posts: 362 View My Garage	Nice I like where can I get mine at?

06-04-2009, 04:26 PM	#14
MerF Go Rays! Drives: 03 Trailblazer Join Date: May 2007 Location: St Pete, Florida Posts: 2,533	Very nice. Can we make better thread titles though?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Songs About Camaros (for your driving pleasure)	Emjay	5th Gen Camaro SS LS LT General Discussions	74	12-18-2014 12:42 AM
Think about this and the Z28 5th gen	13F20	Camaro ZL1 Forum - ZL1 Specific Topics	41	09-04-2010 12:59 AM
10 Camaros that should be built	SSOOCH	5th Gen Camaro SS LS LT General Discussions	47	11-03-2009 05:46 PM
Motorgen LA Invasion Videos (58) and Pics Thread	SeanPlunk	USA - California	5	05-31-2009 01:23 AM
Fesler-Moss Camaro Announced	swchopper	5th Gen Camaro SS LS LT General Discussions	72	05-07-2009 09:40 AM