Add HUD to your 2010 - Page 75 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

turboguy327 · 11-28-2010, 07:36 PM

Quote:

Originally Posted by 2SSRS

In a word YES.

Is it more complicated than a 2010?? Would I need additional parts?

2SSRS@Gen5diy · 11-28-2010, 07:46 PM

That i do not know for a fact, But do not believe so, If you pm me your phone and name we can see, If you like to try i can help and try to find out.

mbrusco103 · 11-28-2010, 07:46 PM

Quote:

Originally Posted by turboguy327

Is it more complicated than a 2010?? Would I need additional parts?

i would imagine it would be about the same if not easier on a 2011 because you might have the correct a/c duct already

Don O · 11-28-2010, 07:47 PM

Thanks for all the pictures. Looks like I'll be doing this 2 weekends from now since I'll have a 3 day weekend (next week is the track). I should have the bezel trim by then and can do the complete install. Keep the pictures coming though, every one can and will be of value when I start.

Thanks again to Ofer for getting this all started.

Don O

franknbeans · 11-28-2010, 07:50 PM

Quote:

Originally Posted by mbrusco103

i would imagine it would be about the same if not easier on a 2011 because you might have the correct a/c duct already

the AC duct is the same for a 2010 and 2011. . . may be easier if you already have the hookups for the HUD.

turboguy327 · 11-28-2010, 07:52 PM

I cant PM. The mods have been ignoring that fact for a couple days now. Once I can PM again I will send that your way. Or PM me your email and I can email to you. I can read PMs just not reply. I just had to buy a new salter for my plow truck so it will be a little while before I can get the "car mod" account full enough for it but if anything I could yank the dash out and check out connectors or what ever you need to know about a LS dash wire harness.

hawkfe · 11-28-2010, 08:02 PM

Hope to do mine the 10th once the harness and hopefully trim arrives........

2SSRS@Gen5diy · 11-28-2010, 08:37 PM

Quote:

Originally Posted by mbrusco103

i would imagine it would be about the same if not easier on a 2011 because you might have the correct a/c duct already

See two posts down from your post for the right info.

Quote:

Originally Posted by Don O

Thanks for all the pictures. Looks like I'll be doing this 2 weekends from now since I'll have a 3 day weekend (next week is the track). I should have the bezel trim by then and can do the complete install. Keep the pictures coming though, every one can and will be of value when I start.

Thanks again to Ofer for getting this all started.

Don O

Glade to make it work.

Quote:

Originally Posted by franknbeans

the AC duct is the same for a 2010 and 2011. . . may be easier if you already have the hookups for the HUD.

Thank you for the help.

Quote:

Originally Posted by turboguy327

I cant PM. The mods have been ignoring that fact for a couple days now. Once I can PM again I will send that your way. Or PM me your email and I can email to you. I can read PMs just not reply. I just had to buy a new salter for my plow truck so it will be a little while before I can get the "car mod" account full enough for it but if anything I could yank the dash out and check out connectors or what ever you need to know about a LS dash wire harness.

Can not pm you it will not let me, But my e-mail is the same as my paypal and that is here in the op.
http://www.camaro5.com/forums/showthread.php?t=114478

Quote:

Originally Posted by hawkfe

Hope to do mine the 10th once the harness and hopefully trim arrives........

You will get in time.

The IOM Ninja · 11-28-2010, 09:53 PM

Hey Patrickt and 2SSRS, out of curiosity would you ship to Canada if the price is right?

2SSRS@Gen5diy · 11-28-2010, 10:12 PM

I will and have done so for other members on light pipes.

brada · 11-28-2010, 11:18 PM

Quote:

Originally Posted by The IOM Ninja

Hey Patrickt and 2SSRS, out of curiosity would you ship to Canada if the price is right?

X2..

i would need the parts sent Vancouver

baba booey · 11-29-2010, 01:02 AM

Quote:

Originally Posted by STINGS

Number 5 is done, so now we have 2 from NJ and 1 from CA and 2 from AZ. Thank you for building the harness Ofer, and thank you Patrick for getting us the parts. Brother got here about 11 so about 3 and 1/2 hours to put it back together. Only had to reindex windows and reset time and date. All radio stations were still there.

Joe

And now we have one in Wa, state. I started at 9:30am Sun and finished at about 8:00 pm. Thanks Ofer and Walt for all the help, I'll try to post some pics on Mon if I can figure out how. The job is not as hard as it looks, it just takes a long time because you need to be very methodical thru the whole process, I bagged all the bolts and screws and labeled the bag for each section

STINGS · 11-29-2010, 04:58 AM

Quote:

Originally Posted by baba booey

And now we have one in Wa, state to started at 9:30am Sun finished at about 8:00 pm Ofer and for all the help I'll try to post some pics on Mon if I can figure out how the job is not as hard as it looks it just takes a long time because you need to be very methodical thru the hole process I bagged all the bolts and screws and labeled the bag for each section

Conratulations Baba Booey!

Think I counted 32 parts lying around the house that were removed! If it had hardware it was sitting with the part.

and then there were 6! Not a bad first weekend guys!

patrickt · 11-29-2010, 07:00 AM

Quote:

Originally Posted by The IOM Ninja

Hey Patrickt and 2SSRS, out of curiosity would you ship to Canada if the price is right?

Yes we do

11-28-2010, 07:47 PM	#1040
Don O Camaro and Vettehead Drives: 2SS/RS IOM L99 69 427/400 Vette Join Date: Aug 2009 Location: 12 miles East of Disneyland - Anaheim Hills Posts: 547 View My Garage	Thanks for all the pictures. Looks like I'll be doing this 2 weekends from now since I'll have a 3 day weekend (next week is the track). I should have the bezel trim by then and can do the complete install. Keep the pictures coming though, every one can and will be of value when I start. Thanks again to Ofer for getting this all started. Don O __________________ Nothing sucks more than that moment during an argument when you realize you're wrong.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
New Camaro Exterior and Interior Stainless Steel Trim Parts from RPI Designs!	RPI Designs	Cosmetics and Lighting Modification Discussions	36	04-02-2020 05:32 PM
February 2010 Camaro production & sales figures. Tops Mustang for 9th straight month!	Tran	5th Gen Camaro SS LS LT General Discussions	52	03-03-2010 09:39 PM
DEALER ONTARIO CANADA WE SHIP ANYWHERE IN CANADA 2010 CAMAROS FOR SALE IN STOCK NOW!	dz	Dealer Camaros for Sale	0	03-03-2010 05:43 PM
Zex Nitrous System for 2010 Camaro SS @ BMC Performance!	Kris@BMCPerformance	Forced Induction	2	02-18-2010 06:59 PM
2010 Chevrolet Camaro makes finalist list for 2010 World Car Design of the Year	Tran	5th Gen Camaro SS LS LT General Discussions	37	02-17-2010 04:22 PM

11-28-2010, 07:46 PM	#1038
2SSRS@Gen5diy Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008 Location: By the lake in AZ Posts: 15,719 View My Garage	That i do not know for a fact, But do not believe so, If you pm me your phone and name we can see, If you like to try i can help and try to find out.

11-28-2010, 07:52 PM	#1042
turboguy327 Banned Drives: 2011 Chevy Camaro Join Date: Sep 2010 Location: USA Posts: 704	I cant PM. The mods have been ignoring that fact for a couple days now. Once I can PM again I will send that your way. Or PM me your email and I can email to you. I can read PMs just not reply. I just had to buy a new salter for my plow truck so it will be a little while before I can get the "car mod" account full enough for it but if anything I could yank the dash out and check out connectors or what ever you need to know about a LS dash wire harness.

11-28-2010, 08:02 PM	#1043
hawkfe Drives: 2014 Stingray 3LT Join Date: Nov 2009 Location: TX Posts: 738 View My Garage	Hope to do mine the 10th once the harness and hopefully trim arrives........

11-28-2010, 09:53 PM	#1045
The IOM Ninja Account Suspended Drives: 10' IOM 2SS/RS, 13' GB Shelby GT500 Join Date: Sep 2010 Location: Sherwood Park, AB Posts: 2,180	Hey Patrickt and 2SSRS, out of curiosity would you ship to Canada if the price is right?

11-28-2010, 10:12 PM	#1046
2SSRS@Gen5diy Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008 Location: By the lake in AZ Posts: 15,719 View My Garage	I will and have done so for other members on light pipes.