11-28-2009, 11:33 PM | #1 |
|
Bolt trouble.......
I don't care if it snaps in half, disappears, or just comes off, how do I remove my pesky bolt that I can barely get the nut loosened because I have to room to loosen the nut under the jeep, I have about 1/4 of an inch to pull the bolt up so how can I break it or something?
|
11-29-2009, 12:14 AM | #2 |
|
Got idea, attach socket to drill, socket on bolt head, turn drill on, whole spinning put hack saw against spinning bolt.
|
11-29-2009, 05:00 PM | #3 |
Drives: 79 formula 'bird, 5th gen soon Join Date: Jul 2008
Location: oklahoma
Posts: 247
|
The answer is obvious.
You must use a sawzall to cut your wheel apart.
__________________
I make my spare spending cash at:http://www.cashcrate.com/1533265
Its legit, you just need to fill out a bunch of boring surveys. |
11-29-2009, 05:03 PM | #4 |
The Mark of Excellence
Drives: 2010 ABM 1SS RS LS3 Join Date: Jan 2009
Location: Smallest State in the Union
Posts: 8,690
|
Sharp chisel, bfh.
__________________
BMR, CAI, DynoMax, Elite Eng., Hurst, Jannetty, Clear Image Headers & Hi Flow cats, Jet Hot, LSR, TSW, VMax, Vredestein |
11-29-2009, 05:16 PM | #5 |
General Motors Aficionado
Drives: 2023 GMC Canyon, 2020 Colorado Join Date: Aug 2008
Location: Florida
Posts: 37,371
|
__________________
2023 GMC Canyon Elevation 2020 Chevrolet Colorado W/T Extended Cab (State-issued) |
11-29-2009, 05:26 PM | #6 |
Go Blue!!!!!
Drives: 2012 Cruze LT Join Date: Mar 2009
Location: Indiana
Posts: 23,290
|
|
11-29-2009, 06:52 PM | #7 |
Drives: 2010 Camaro 2SS Join Date: Aug 2009
Location: NorCal
Posts: 958
|
|
11-29-2009, 08:27 PM | #8 |
|
|
11-29-2009, 08:27 PM | #9 |
|
|
11-29-2009, 08:49 PM | #10 |
Banned
Drives: 1991 New Yorker, 69 Tbird, ABM2SSRS Join Date: May 2009
Location: BC Canada
Posts: 2,248
|
Drill out the bolt if you can and use an ez out orrr
JB weld a socket in there and use your ratchet or a wrench. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
DIY : Install underdrive pulley on 2010 Camaro SS | Nine Ball | Camaro DIY & HOW-TO instructions & discussions | 34 | 09-30-2013 08:25 PM |
PWA "The Lounge" | DGthe3 | Off-topic Discussions | 143773 | 11-06-2010 11:00 AM |
AIRAID Intake System For 2010 3.6L V6 Camaro | Airaid Filters | Camaro V6 LLT Engine, Exhaust, and Bolt-Ons | 362 | 02-26-2010 08:35 PM |
Is the factory exhaust system bolt on or welded??? | 1sickss | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 18 | 10-30-2009 02:55 PM |
9 bolt vs 10 bolt | wilnot | 3rd Generation Camaros | 2 | 09-30-2009 04:22 PM |