04-21-2015, 01:33 PM | #1 |
Santos
Drives: 1SS Blk 6M ECS 1500 Join Date: Jul 2007
Location: Virginia Beach, Virginia
Posts: 606
|
2010 6M 40k miles Very bad vibration
So i am no mechanic by any means, but i know something is really going on with the car, and am tight on money so any help to get me looking in the right place would be very helpful. i have don't a search and can't find anything on an SS.
So i was driving the other day just fine, the next day i hit the gas and accelerate to about 36- 40 mph in third i believe. The car starts vibrating like the wheels in the rear are both going to come off.. i have not had any type of service other than an oil change as of late, and topping off my PS fluid. From 40-60 is when it is at its worst, and from 3rd to 5th gear id say. It vibrates the whole car, mirrors and all, i cannot hear any strange noise coming from the engine bay, and is perfect when sitting idle. From the other threads i have found anywhere close in topic, it may be a wheel bearing, differential, or engine mounts.. can anyone help, this car is to new and taken care of to well for it to be acting like this and is out of warranty now.
__________________
|
04-21-2015, 02:08 PM | #2 |
Drives: 2014 2SS 1LE AGM Join Date: May 2013
Location: raleigh
Posts: 301
|
Jack the rear up and rotate the tires. If it's a wheel bearing you will hear it near the hub.
I had a differential go bad in a Tahoe and that was the nail in the coffin b/c it would cost more then what the truck was worth.
__________________
|
04-21-2015, 02:11 PM | #3 |
Drives: 2011 SS (Sparrow Spearer???) Join Date: Aug 2013
Location: South of OKC, OK
Posts: 707
|
check your wheels for missing balancing weights or go get them balanced. have you recently bought new tires, if so, take them to where you got them, have them rebalance them. other than that, get under the car and check driveshaft bolts, driveshaft support bearing, bolts on axles, suspension, etc. good luck
__________________
Black magic woman, don't turn your back on me baby!
|
04-21-2015, 03:04 PM | #4 |
Santos
Drives: 1SS Blk 6M ECS 1500 Join Date: Jul 2007
Location: Virginia Beach, Virginia
Posts: 606
|
very hard to see, have only had one tire change on these rims, don't know how many weights usually go on a rim but there are some already on this rim, but also looks like there is some missing...
__________________
|
04-21-2015, 06:02 PM | #5 |
376 cubic inches of fun
|
If you put it in neutral and the vibration doesn't stop, then obviously it's not the engine.
Usually, speed dependent vibrations are wheel related. Start by looking for missing balance weights. I see you may have already spotted that as a probable cause. |
04-22-2015, 03:06 PM | #6 |
Santos
Drives: 1SS Blk 6M ECS 1500 Join Date: Jul 2007
Location: Virginia Beach, Virginia
Posts: 606
|
well balanced and aligned… still vibrating… $hit
__________________
|
04-25-2015, 07:05 PM | #7 |
Look at driveshaft couplers . They like to wear out
|
|
04-26-2015, 07:56 AM | #8 |
Drives: camaro Join Date: Apr 2015
Location: CA
Posts: 2
|
Start by looking for missing balance weights. I see you may have already spotted that as a probable cause.
|
04-27-2015, 06:33 PM | #9 |
|
Check the lower control arm, the sway bar tears out on the 2010's. Mine did.
__________________
SPi Performance Stage 3 package Comp Cam
PHADT FE4 ZL Stg.3 VMAX CNC Spiral Ported Throttle Body Dynatech LT headers, Hi flow Cats MBRP 3" 304 stainless X-pipe exhaust Fastlane true CAI. Barton shifter |
04-28-2015, 07:20 PM | #10 |
Santos
Drives: 1SS Blk 6M ECS 1500 Join Date: Jul 2007
Location: Virginia Beach, Virginia
Posts: 606
|
Found the culprit for any of y'all who run into the same issue. Thx for all the help yall
__________________
|
04-28-2015, 07:59 PM | #11 |
Drives: 2010 Camaro 2SS/RS Join Date: Dec 2009
Location: Grand Prairie, Texas
Posts: 1,608
|
Ok so what is that Bolt from?
__________________
94 Firebird Formula (Drowned 08/30/05)
2010 IBM 2SS/RS 6M Arrived 3/25/10. ADM CAI, Borla Type S Cat Back, VMAX Ported TB, LG Short Throw Shifter, 1LE Shocks, Hotchkis Sway Bars, Whiteline Cradle Bushing Inserts, Custom Powdercoated ZL1's ,Michelin Pilot Supersports, Stainless Power Headers, Solo J Pipes, AAC LED Sidemarkers, ZL1 Rockers, SLP Splitter, ADM Stage II Cam,ZL1 Diffuser,Vitesse Throttle Controller. |
04-29-2015, 04:52 AM | #12 |
Santos
Drives: 1SS Blk 6M ECS 1500 Join Date: Jul 2007
Location: Virginia Beach, Virginia
Posts: 606
|
Driveshaft. This was cracked not all the way broke till they got it out and some were loose, all in the rear
__________________
|
04-30-2015, 11:40 AM | #13 |
Drives: 2010 CGM Camaro 2SS/LS3 Join Date: Oct 2013
Location: Raleigh-Durham
Posts: 1,409
|
Interesting, I noticed some high speed vibes in my car around 80, it's not the tires but maybe I need to check my driveshaft bolts, I have some new ones anyway already.
Also I wish chevy used a one piece in these cars, another possibility is the center support bearing. Glad to see you found your issue though.
__________________
2010 2SS
BMR 1" Springs Koni Orange struts/shocks 1LE rear sway bar SRP Racing Pedals Hurst Billet short shifter Square tire/wheel setup Elite Engineering Catch Can Stainless Power longtubes/highflow cats K&N Typhoon CAI RPM Motorsports of Garner, NC dyno tune (421 RWHP) |
|
|
|
|