Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
Bigwormgraphix
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Engine | Drivetrain | Powertrain Technical Discussions > Forced Induction - V8


Reply
 
Thread Tools
Old 09-20-2011, 03:38 PM   #1
Granatelli
Account Suspended
 
Drives: 2SS Victory Red
Join Date: Jul 2009
Location: Oxnard
Posts: 1,093
Edelbrock Blower Question

I have a customer that is bringing in his 2011 SS that already has a stock Edelbrock blower on his stock motor. We are building him a stout long blower and I wanted to pulley it up (smaller blower pulley) how small can I go without slipping the 6 rib and what should be the belt length - please and thanks in advance
Granatelli is offline   Reply With Quote
Old 09-20-2011, 07:31 PM   #2
Busy_Boi
SoCal C5 Family Member
 
Busy_Boi's Avatar
 
Drives: RJT 2010 camaro 2SS
Join Date: Aug 2009
Location: Los Angeles, CA
Posts: 1,016
Send a message via Yahoo to Busy_Boi
Right now I have the 2.75 pulley on my E-Force with the Goodyear belt part#GDY4061030 and no slipping at all.
__________________
Busy_Boi is offline   Reply With Quote
Old 09-21-2011, 03:20 PM   #3
Granatelli
Account Suspended
 
Drives: 2SS Victory Red
Join Date: Jul 2009
Location: Oxnard
Posts: 1,093
Quote:
Originally Posted by Busy_Boi View Post
Right now I have the 2.75 pulley on my E-Force with the Goodyear belt part#GDY4061030 and no slipping at all.
Thanks - that is what I was looking for
Granatelli is offline   Reply With Quote
Old 09-21-2011, 03:53 PM   #4
Mike@RMCR
 
Mike@RMCR's Avatar
 
Drives: Supercharged
Join Date: Oct 2009
Location: Colorado Springs
Posts: 314
I would also do the fuel line mod on the rails. Have seen alot of these superchargers run the rails dry, do to the way edelbrock runs them.
Mike@RMCR is offline   Reply With Quote
Old 09-21-2011, 04:17 PM   #5
Granatelli
Account Suspended
 
Drives: 2SS Victory Red
Join Date: Jul 2009
Location: Oxnard
Posts: 1,093
Quote:
Originally Posted by Mike@RMCR View Post
I would also do the fuel line mod on the rails. Have seen alot of these superchargers run the rails dry, do to the way edelbrock runs them.
I will look into that as well
Granatelli is offline   Reply With Quote
Old 09-21-2011, 08:56 PM   #6
Busy_Boi
SoCal C5 Family Member
 
Busy_Boi's Avatar
 
Drives: RJT 2010 camaro 2SS
Join Date: Aug 2009
Location: Los Angeles, CA
Posts: 1,016
Send a message via Yahoo to Busy_Boi
Quote:
Originally Posted by Mike@RMCR View Post
I would also do the fuel line mod on the rails. Have seen alot of these superchargers run the rails dry, do to the way edelbrock runs them.
Yes he is right about that and maybe some 72lbs injectors too.
__________________
Busy_Boi is offline   Reply With Quote
Old 09-22-2011, 05:23 PM   #7
Granatelli
Account Suspended
 
Drives: 2SS Victory Red
Join Date: Jul 2009
Location: Oxnard
Posts: 1,093
Quote:
Originally Posted by Busy_Boi View Post
Yes he is right about that and maybe some 72lbs injectors too.
What inj does Edelbrock include in their kit
Granatelli is offline   Reply With Quote
Old 09-22-2011, 06:51 PM   #8
Camaro_Custom_Painted
Choke on that causality!
 
Camaro_Custom_Painted's Avatar
 
Drives: 2010 2SS/RS
Join Date: Sep 2009
Location: Minnesota
Posts: 645
Quote:
Originally Posted by Granatelli View Post
What inj does Edelbrock include in their kit
They ship 52lb with the kit. Bosch 0280158187.

Bosch ZR1 52lb/hour with EV6 / USCAR Connector - Direct fit for LS9
__________________
Edelbrock EForce - Stainless Works Headers - BMR Sways & Arms & Toe Links & Control Arm Bushings & End Links - Rotofab CAI - Assorted Interior, Exterior, Underhood Bling - Red Jewel Stripes & Full Body Clear - Lexani LX15 Wheels - JRE Fuel Rail Upgrade - Kenne Bell BAP - Heartthrob XPipe - Elite Catch Can - Pedders Cradle & Front Arm Bushings - Hotchkis Strut Brace - MSD Wires - Carbotech Brakes - DSS 1000HP Axles & Driveshaft - Mickey Thompson Tires - Halo Harness - AutoMeter A/F, Boost, Fuel Pressure Gauges - Whats Next?

Last edited by Camaro_Custom_Painted; 09-22-2011 at 07:02 PM.
Camaro_Custom_Painted is offline   Reply With Quote
Old 09-22-2011, 06:54 PM   #9
coptzr
Resistance is futile
 
coptzr's Avatar
 
Drives: Anything thats fast
Join Date: May 2009
Location: Big Rapids,MI
Posts: 315
Running the 52's that came with the blower, they are ZR1 injectors, from what I have been told. I'm at 583 RWHP with stock pully and CTS-V dual pump and module. No issues at all.
__________________
Modifications (so far)
Edelbrock E-Force supercharger
JRE fuel system upgrade
Edelbrock CAI
VMS stage 2.5 cam kit
SLP LT's, no cats
NPP muffler's w/x-pipe
Tuned at Vector Motorsports
606 RWHP and 567 RWT
Black 1LE 10 spokes.
Hotchkis drop springs.
coptzr is offline   Reply With Quote
Old 09-22-2011, 07:39 PM   #10
JM10
Se habla espaņol
 
JM10's Avatar
 
Drives: 2010 Camaro SS/RS VR
Join Date: Jun 2009
Location: Arizona/Sonora
Posts: 605
At 540rwhp the 52sīs were "almost" max out (90-98% cycle) according to my tuner.

JM
__________________
2010 VR 2SS/RS
BMR Suspension Parts
Hendrix HD Axles
DSS Aluminum Shaft
RPM Diff / 3.91 Gears
LPE ZR1 Clutch
Edelbrock E-Force SC / JRE Fuel Upgrade
Livernois 1C cam 570 rwhp/559 rwtq SAE
Best 1/4 time: 11.43
JM10 is offline   Reply With Quote
Old 09-26-2011, 03:17 PM   #11
S-eatin-grin

 
S-eatin-grin's Avatar
 
Drives: 2013 2SS/RS AGM
Join Date: Nov 2010
Location: WV
Posts: 1,170
If you are going to a smaller pulley (increasing boost) with the e-force on a stock shortblock you better feed it and tune it right or bad things will happen...the questions being asked here tell me that your experience with this blower is limited. I'd call Ted Jannetty at JRE and get some "industry-advice" before you end up with a pissed-off customer with a trashed motor.
S-eatin-grin is offline   Reply With Quote
Old 09-26-2011, 04:49 PM   #12
Granatelli
Account Suspended
 
Drives: 2SS Victory Red
Join Date: Jul 2009
Location: Oxnard
Posts: 1,093
Quote:
Originally Posted by S-eatin-grin View Post
If you are going to a smaller pulley (increasing boost) with the e-force on a stock shortblock you better feed it and tune it right or bad things will happen...the questions being asked here tell me that your experience with this blower is limited. I'd call Ted Jannetty at JRE and get some "industry-advice" before you end up with a pissed-off customer with a trashed motor.
I have no experience with the Edelbrock that is why I was asking I have a ton of experience with FI. As I owned Paxton Superchargers for 8 years and before that I worked there for 12 - So 20 years of Paxton, I raced Indy Car and owned a team back when it was CART and turbo'd. We also build many single and twin turbo kits for customers.

Edelbrock on a Gen 5 Camaro - not so much,

We are building this person a long block with great flowing heads and all the bottom end parts to safely support 800.

As for 52's. I understand and will monitor inj pres and flow. And for the record a 52 will support 756 crank HP at 60psi at .55 bsfc

This customer will be super happy with 600 rwhp so I should be safe
Granatelli is offline   Reply With Quote
Old 09-26-2011, 05:38 PM   #13
SC2150
Account Suspended
 
Drives: 2012 Camaro RS, RX supercharged
Join Date: Dec 2009
Location: Bradenton, FL
Posts: 6,063
If you need we can machine in the "Gator Grip" anti-slip patteren. No real increased wear and makes a big difference. PM me for details.
SC2150 is offline   Reply With Quote
Old 09-26-2011, 07:15 PM   #14
S-eatin-grin

 
S-eatin-grin's Avatar
 
Drives: 2013 2SS/RS AGM
Join Date: Nov 2010
Location: WV
Posts: 1,170
Quote:
Originally Posted by Granatelli View Post
I have no experience with the Edelbrock that is why I was asking I have a ton of experience with FI. As I owned Paxton Superchargers for 8 years and before that I worked there for 12 - So 20 years of Paxton, I raced Indy Car and owned a team back when it was CART and turbo'd. We also build many single and twin turbo kits for customers.

Edelbrock on a Gen 5 Camaro - not so much,

We are building this person a long block with great flowing heads and all the bottom end parts to safely support 800.

As for 52's. I understand and will monitor inj pres and flow. And for the record a 52 will support 756 crank HP at 60psi at .55 bsfc


This customer will be super happy with 600 rwhp so I should be safe
I meant no offense and I guess I didn't quite get the part where you said you were replacing the stock internals. Sounds like it will be a beast and I will be curious to hear the results. I've been wondering what the strongest e-force build out there is to date on a gen 5 camaro?? maybe this will be the one
S-eatin-grin is offline   Reply With Quote
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Stock L99 A6 Supercharger options, opinions, & experiences 2010 Bumblebee Forced Induction - V8 110 01-25-2019 04:23 PM
Question about tire sizes Jram1588 Wheels and Tires Talk Sponsored by The Tire Rack 9 07-17-2010 07:27 AM
Custom wheel offset question ... Bowtie Junkman Wheels and Tires Talk Sponsored by The Tire Rack 4 04-23-2010 05:16 PM
Question for blower Guru's carguy Forced Induction - V8 15 04-16-2010 10:57 AM
Question Involving 4.10 gears & Bushings Deric884 V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6) 1 02-13-2010 06:53 AM


All times are GMT -5. The time now is 05:24 AM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.