z28 wickerbill

[1985airborne]

I have to get my hands on the z28 wickerbill...Anybody have a part# and is it available yet? Thanks

[neptunetrucking]

Originally Posted by 1985airborne

I have to get my hands on the z28 wickerbill...Anybody have a part# and is it available yet? Thanks

23200132 - Z/28 Spoiler Extension Kit

[RaySouth]

Still not available. I tried yesterday.

[White_SS/RS]

Do the 2014 SS spoilers have the same arch across the back of the spoiler (wicker bill mounting surface) as the Z28?

I would like to install the wicker bill on my '14 1LE when it's available but if the shape of the back (mounting surface) of the spoiler is much different from the Z28 then this just won't be possible. Not only that will an SS spoiler have the internal strength to allow the installation of threaded inserts and bolts but also the increase in wind force associated with the wicker bill.

[tw78911sc]

Sebring pictures of spoiler

[RaySouth]

I may be wrong but the higher arched portion of the Z/28 spoiler is not a mountable surface. Results are that you should be able to mount to earlier shorter versions as the mountable area visually appears to be equal.

[RocketFueledLSA]

Any updates on availability? I contacted my local dealership last week and they apparently do not have this part in the system at all. He gave me the full Z28 spoiler part number and even it is on back order. So my next question is this..... if GM is really going to make this part available at the beginning of Q3 why don't any of the currently available Z28s have this option? Has anyone had any luck with this tracking down information for this?

[SamHouseIII]

I found this...

A new accessory for 2014-2015 Camaros is the wicker bill spoiler (part number 23200130), which adds up to 150 lbs. of downforce to the rear of the vehicle at high speeds. The wicker bill spoiler is compatible with the 2014 accessory wing spoiler (RPO SB3). It is not restricted to only Z/28 models.
During installation of the wicker bill spoiler, the template should be lined up on the lower feature line of the Original Equipment (OE) spoiler to ensure a consistent gap at the top of the template to the top of the spoiler.
Seven holes are drilled in the OE spoiler. Use a graduated drill bit due to the irregular hole size required for the M8 riv-nuts. The riv-nuts should easily slide in and out of the drilled holes.
Install the M8 riv-nuts using the M8 riv-nut installation tool. The correct tool must be used to ensure proper installation of the riv-nuts. The riv-nut installation tool (BO-42151-8MM-KIT) can be ordered by calling 1-800 GM TOOLS (1-800-468-6657) or online using the Service Workbench link in GM GlobalConnect.
Rubber grommets are placed over the M8 riv-nuts to prevent water intrusion. In addition, two rubber grommets are added to the decklid stops.
For a copy of the complete installation instructions, refer to the Camaro Accessory Installation Manual available in the Service Information.

[2SSRS@Gen5diy]

Originally Posted by SamHouseIII

I found this...

A new accessory for 2014-2015 Camaros is the wicker bill spoiler (part number 23200130), which adds up to 150 lbs. of downforce to the rear of the vehicle at high speeds. The wicker bill spoiler is compatible with the 2014 accessory wing spoiler (RPO SB3). It is not restricted to only Z/28 models.
During installation of the wicker bill spoiler, the template should be lined up on the lower feature line of the Original Equipment (OE) spoiler to ensure a consistent gap at the top of the template to the top of the spoiler.
Seven holes are drilled in the OE spoiler. Use a graduated drill bit due to the irregular hole size required for the M8 riv-nuts. The riv-nuts should easily slide in and out of the drilled holes.
Install the M8 riv-nuts using the M8 riv-nut installation tool. The correct tool must be used to ensure proper installation of the riv-nuts. The riv-nut installation tool (BO-42151-8MM-KIT) can be ordered by calling 1-800 GM TOOLS (1-800-468-6657) or online using the Service Workbench link in GM GlobalConnect.
Rubber grommets are placed over the M8 riv-nuts to prevent water intrusion. In addition, two rubber grommets are added to the decklid stops.
For a copy of the complete installation instructions, refer to the Camaro Accessory Installation Manual available in the Service Information.

Yes there out, and some member's have them, so to the Z/28 side of the forum for more info.

[jonm38]

ZL1 Wickerbill Rear Spoiler for 2012-2013 Chevrolet Camaro fits Zl1 models (Matte Black finish)

SKU: 1601-25.

$365.00 $310.25

AT: DJ Grills.

Then you have to have the - ZL1 Wickerbill Rear Spoiler Installation Kit for 2012-2013 Chevrolet Camaro fits Zl1 models ( finish)

That's about $127.00

Originally Posted by 1985airborne

I have to get my hands on the z28 wickerbill...Anybody have a part# and is it available yet? Thanks