Titanium lugnuts for Z/28 - Page 9 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

joelster · 04-15-2020, 06:29 AM

Anyone have any updates? I tried the OZMO site and it says "out of stock", and nobody replied to my email. Does anyone else sell similar lugs?

Yessa · 04-15-2020, 11:41 AM

Good luck.

olblue75 · 04-15-2020, 08:23 PM

https://dsxtuning.com/collections/fi...28758490447952

Here you go.

joelster · 04-16-2020, 05:48 PM

Thank you!!!!

joelster · 04-22-2020, 04:49 PM

They arrived and I decided to weigh them and install them. I used a very fine digital fishing scale.

Total weight saved over all 4 wheels is 1.96lbs so almost 1/2 lb per wheel of unsprung weight. Not bad for $158 (with shipping)

ronchev · 04-23-2020, 08:06 AM

Quote:

Originally Posted by olblue75

https://dsxtuning.com/collections/fi...28758490447952

Here you go.

Thanks for the link, mine showed up yesterday..These are nice nuts

joelster · 05-07-2020, 08:22 PM

The ones I got from the link provided aren’t phony. I weighed them. They save 1.96lbs.

Flubyux2 · 06-08-2020, 01:38 AM

Are these impact safe? I know ti is brittle so I’m a bit concerned putting my Milwaukee to a ti lug nut.

joelster · 06-16-2020, 10:03 PM

I always break lugs loose by hand. I’ll use an impact after they are loose. I never bang them on with an impact either.

04-15-2020, 06:29 AM	#113
joelster Drives: '94 Z28+ '15 Z/28 Join Date: Jun 2009 Location: Cheektowaga, NY Posts: 1,282	Anyone have any updates? I tried the OZMO site and it says "out of stock", and nobody replied to my email. Does anyone else sell similar lugs? __________________ 1973 Mach 1, 351C cruiser '15 Z/28 Red Hot, A/C 1980 Z28- resto-mod project 1979 Y84 Trans Am 1986 IROC-Z

04-15-2020, 08:23 PM	#115
olblue75 Drives: 2010 2SS/RS Join Date: Dec 2009 Location: Clarksville Tennesse. Posts: 6,064	https://dsxtuning.com/collections/fi...28758490447952 Here you go. __________________ Orange Krush II 1LE Front sway bar, Splitter, shocks and struts, Z28 dual mode mufflers, Intake, UCA Bushings, and Toresen 3.91 Diff. 1 piece DSS Drive Shaft, ZL1/C7 Calipers, and 32mm JPSS Rear Bar. ASC race spec splitter and wicker. 6th Gen M017 Wheels. Stainless Works 1 7/8 LTs. DSE and PAFDT Suspension components.

04-16-2020, 05:48 PM	#116
joelster Drives: '94 Z28+ '15 Z/28 Join Date: Jun 2009 Location: Cheektowaga, NY Posts: 1,282	Thank you!!!! __________________ 1973 Mach 1, 351C cruiser '15 Z/28 Red Hot, A/C 1980 Z28- resto-mod project 1979 Y84 Trans Am 1986 IROC-Z

04-22-2020, 04:49 PM	#117
joelster Drives: '94 Z28+ '15 Z/28 Join Date: Jun 2009 Location: Cheektowaga, NY Posts: 1,282	They arrived and I decided to weigh them and install them. I used a very fine digital fishing scale. Total weight saved over all 4 wheels is 1.96lbs so almost 1/2 lb per wheel of unsprung weight. Not bad for $158 (with shipping) __________________ 1973 Mach 1, 351C cruiser '15 Z/28 Red Hot, A/C 1980 Z28- resto-mod project 1979 Y84 Trans Am 1986 IROC-Z

05-07-2020, 08:22 PM	#119
joelster Drives: '94 Z28+ '15 Z/28 Join Date: Jun 2009 Location: Cheektowaga, NY Posts: 1,282	The ones I got from the link provided aren’t phony. I weighed them. They save 1.96lbs. __________________ 1973 Mach 1, 351C cruiser '15 Z/28 Red Hot, A/C 1980 Z28- resto-mod project 1979 Y84 Trans Am 1986 IROC-Z

04-15-2020, 11:41 AM	#114
Yessa Account Suspended Drives: 2015 Camaro Z/28 Join Date: May 2019 Location: FLORIDA Posts: 222	Good luck.

06-08-2020, 01:38 AM	#120
Flubyux2 Drives: 2014 #036 summit white Join Date: May 2020 Location: Spring Hill, Fl Posts: 13	Are these impact safe? I know ti is brittle so I’m a bit concerned putting my Milwaukee to a ti lug nut.

06-16-2020, 10:03 PM	#121
joelster Drives: '94 Z28+ '15 Z/28 Join Date: Jun 2009 Location: Cheektowaga, NY Posts: 1,282	I always break lugs loose by hand. I’ll use an impact after they are loose. I never bang them on with an impact either. __________________ 1973 Mach 1, 351C cruiser '15 Z/28 Red Hot, A/C 1980 Z28- resto-mod project 1979 Y84 Trans Am 1986 IROC-Z