My 2SS - Page 5 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

2SSRS@Gen5diy · 01-02-2010, 06:45 PM

The fill part for the grill is from SLP And the SS emblem is from any GM dealer All you have to do is use a heat gun or hair dryer to bend it to fit.

And yes i did the rear the same way.

Darth_Emma · 01-03-2010, 06:12 PM

Sorry to keep pestering, but my understanding is that removing the rear bowtie leaves a bit of a hole or pit. How did you cover that? I like the SS much better.

2SSRS@Gen5diy · 01-04-2010, 11:22 AM

Yes there is two holes under the rear SS Emblem, But if you use the Part # 15211285 that i told you it will cover the two holes up.

2SSRS@Gen5diy · 01-09-2010, 09:14 PM

Got my new OEM fenders to make the ZR1 look on them, Will post some pics as soon as we are done.

2SSRS@Gen5diy · 01-18-2010, 04:10 PM

Added red LED's to my Homelink so you can see the 3 buttons.

2SSRS@Gen5diy · 01-18-2010, 08:54 PM

Here is a night pic of the new Homelink with LED's.

P. Ham · 01-18-2010, 09:48 PM

Slick mod! That's how it should have been from the get-go.

2SSRS@Gen5diy · 01-18-2010, 09:53 PM

Agreed, Its not a lot of $ i think i have like $2.00 in parts

2SSRS@Gen5diy · 01-19-2010, 09:27 AM

OK update Got the new plastic tube from K&N and here is a pic of it i do not have the part # at this time.

ttexxan · 01-19-2010, 02:18 PM

Dumb question but what is the differance in using the chrome piece you have verses the plastic. Is it larger

2SSRS@Gen5diy · 01-19-2010, 05:01 PM

There is no difference in the two other then the look's

ttexxan · 01-24-2010, 08:08 PM

Would one be better from a Cold intake department??? Any contraversy there??

2SSRS@Gen5diy · 01-24-2010, 10:10 PM

No i don't think so as the two pipe will not give you the coldest Air temp.

2SSRS@Gen5diy · 01-24-2010, 10:27 PM

OK as Jayhawk500 posted his Thread on how to do the ABL Lighting of the HOMELINK BUTTONS i will post the way i did my car,

Its a lot like he did his put i used 3 small LED's and i did not remove the A pillar you can run the wire from the HOMELINK froward to the windshield, now that its at the windshield go in the front and pull it to the drivers A pillar.

Now pull out the weatherstrip from the driver door at the point of the A pillar and then take the wire from the front and fish it under the headliner at the windshield and pull it down.

Push the wire down the A pillar and pull the fuse cover off so you can wire it up to the ABL

01-18-2010, 08:54 PM	#62
2SSRS@Gen5diy Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008 Location: By the lake in AZ Posts: 15,719 View My Garage	Here is a night pic of the new Homelink with LED's. Attached Images

01-18-2010, 09:48 PM	#63
P. Ham Drives: IOM 2LT/RS Join Date: Sep 2009 Location: San Antonio, TX Posts: 169 View My Garage	Slick mod! That's how it should have been from the get-go. __________________ It's not polite to stare.

01-19-2010, 09:27 AM	#65
2SSRS@Gen5diy Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008 Location: By the lake in AZ Posts: 15,719 View My Garage	OK update Got the new plastic tube from K&N and here is a pic of it i do not have the part # at this time. Attached Images

01-24-2010, 10:27 PM	#70
2SSRS@Gen5diy Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008 Location: By the lake in AZ Posts: 15,719 View My Garage	OK as Jayhawk500 posted his Thread on how to do the ABL Lighting of the HOMELINK BUTTONS i will post the way i did my car, Its a lot like he did his put i used 3 small LED's and i did not remove the A pillar you can run the wire from the HOMELINK froward to the windshield, now that its at the windshield go in the front and pull it to the drivers A pillar. Now pull out the weatherstrip from the driver door at the point of the A pillar and then take the wire from the front and fish it under the headliner at the windshield and pull it down. Push the wire down the A pillar and pull the fuse cover off so you can wire it up to the ABL Attached Images

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
65 Camaro's to choose from.	tony_c	Camaro Price \| Ordering \| Tracking \| Dealers Discussions	25	08-29-2009 03:25 PM
Why aren't there any Aqua Blues yet?	txcamarogirl	5th Gen Camaro SS LS LT General Discussions	40	08-20-2009 10:05 AM
why get an rs package on the 2ss?	LS3SSRS	5th Gen Camaro SS LS LT General Discussions	66	08-16-2009 05:14 PM
Check your Order here	bvonscott	Camaro Price \| Ordering \| Tracking \| Dealers Discussions	665	06-29-2009 01:00 PM
Exhaust Upgrade for 2SS	ericeast	Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons	7	05-19-2009 10:02 PM

01-02-2010, 06:45 PM	#57
2SSRS@Gen5diy Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008 Location: By the lake in AZ Posts: 15,719 View My Garage	The fill part for the grill is from SLP And the SS emblem is from any GM dealer All you have to do is use a heat gun or hair dryer to bend it to fit. And yes i did the rear the same way.

01-03-2010, 06:12 PM	#58
Darth_Emma Psssssssssshhhhhhhhhhhhh! Drives: under contruction Join Date: Nov 2009 Location: Marysville, Ohio Posts: 12,996 View My Garage	Sorry to keep pestering, but my understanding is that removing the rear bowtie leaves a bit of a hole or pit. How did you cover that? I like the SS much better.

01-04-2010, 11:22 AM	#59
2SSRS@Gen5diy Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008 Location: By the lake in AZ Posts: 15,719 View My Garage	Yes there is two holes under the rear SS Emblem, But if you use the Part # 15211285 that i told you it will cover the two holes up.

01-09-2010, 09:14 PM	#60
2SSRS@Gen5diy Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008 Location: By the lake in AZ Posts: 15,719 View My Garage	Got my new OEM fenders to make the ZR1 look on them, Will post some pics as soon as we are done.

01-18-2010, 04:10 PM	#61
2SSRS@Gen5diy Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008 Location: By the lake in AZ Posts: 15,719 View My Garage	Added red LED's to my Homelink so you can see the 3 buttons.

01-18-2010, 09:53 PM	#64
2SSRS@Gen5diy Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008 Location: By the lake in AZ Posts: 15,719 View My Garage	Agreed, Its not a lot of $ i think i have like $2.00 in parts

01-19-2010, 02:18 PM	#66
ttexxan Drives: 2010 Camaro SS/RS Join Date: Oct 2009 Location: Fort Worth Texas Posts: 926	Dumb question but what is the differance in using the chrome piece you have verses the plastic. Is it larger

01-19-2010, 05:01 PM	#67
2SSRS@Gen5diy Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008 Location: By the lake in AZ Posts: 15,719 View My Garage	There is no difference in the two other then the look's

01-24-2010, 08:08 PM	#68
ttexxan Drives: 2010 Camaro SS/RS Join Date: Oct 2009 Location: Fort Worth Texas Posts: 926	Would one be better from a Cold intake department??? Any contraversy there??

01-24-2010, 10:10 PM	#69
2SSRS@Gen5diy Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008 Location: By the lake in AZ Posts: 15,719 View My Garage	No i don't think so as the two pipe will not give you the coldest Air temp.