Need some wiring help - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

ubrimah · 08-12-2013, 10:12 PM

How can I pass a wire from my center console into the door panels?

markkk · 08-12-2013, 10:26 PM

What is this for? lighting the door panels?

ubrimah · 08-12-2013, 11:26 PM

Quote:

Originally Posted by markkk

What is this for? lighting the door panels?

I have an RGB cable to light up the strips in my front speakers and the main controller is in my center console

ubrimah · 08-13-2013, 12:49 AM

Buschman · 08-13-2013, 04:39 AM

Can't you run it from the counsel, up to the dash, and then down to the doors thru the grommet with the factory wiring?

sjmautoprod · 08-13-2013, 07:23 AM

As I recall, there are only a couple unused cavities in the door-harness connector that you can run wires through. You may need to drill holes.

ubrimah · 08-13-2013, 01:18 PM

Quote:

Originally Posted by Buschman

Can't you run it from the counsel, up to the dash, and then down to the doors thru the grommet with the factory wiring?

I was thinking the same but the grommet is blocked off on both sides and I would probably mess something up of i tried to drill through it haha

ubrimah · 08-16-2013, 01:03 AM

Any other ideas?

DraggnFrameGMC · 08-16-2013, 09:14 AM

Its not bad to drill out. There are a geoup of 3 or 4 empty slots together. I took a hot iron and ran it in the middle of them first to open it up then went in with my dremel. I was able to put a few 12ga wires through

08-12-2013, 10:12 PM	#1
ubrimah Oreo Drives: Summit White LT/RS A6 Join Date: Dec 2010 Location: Waco TX Posts: 1,248	Need some wiring help How can I pass a wire from my center console into the door panels? __________________ Click the pic!

08-12-2013, 10:26 PM	#2
markkk Drives: 2012 Camaro 1LS Join Date: May 2012 Location: NC Posts: 127	What is this for? lighting the door panels? __________________

08-13-2013, 12:49 AM	#4
ubrimah Oreo Drives: Summit White LT/RS A6 Join Date: Dec 2010 Location: Waco TX Posts: 1,248	__________________ Click the pic!

08-13-2013, 04:39 AM	#5
Buschman Drives: 2018 ZL1 2015 1SS 1LE Join Date: May 2013 Location: North Eastern Michigan Posts: 772	Can't you run it from the counsel, up to the dash, and then down to the doors thru the grommet with the factory wiring? __________________ 2018 ZL1 2015 1SS 1LE Stock...ish

08-16-2013, 01:03 AM	#8
ubrimah Oreo Drives: Summit White LT/RS A6 Join Date: Dec 2010 Location: Waco TX Posts: 1,248	Any other ideas? __________________ Click the pic!

08-13-2013, 07:23 AM	#6
sjmautoprod Drives: '16 2SS Join Date: Apr 2011 Location: Chicago Suburbs Posts: 2,271	As I recall, there are only a couple unused cavities in the door-harness connector that you can run wires through. You may need to drill holes.

08-16-2013, 09:14 AM	#9
DraggnFrameGMC Drives: 2011 Synergy Green Camaro LT Join Date: Jul 2011 Location: Lakeland, FL Posts: 830	Its not bad to drill out. There are a geoup of 3 or 4 empty slots together. I took a hot iron and ran it in the middle of them first to open it up then went in with my dremel. I was able to put a few 12ga wires through