10-13-2018, 11:16 AM | #183 |
Drives: 12 camaro ss, 72 chevelle, 91camaro Join Date: Dec 2013
Location: findlay,oh
Posts: 2,069
|
got a ljms cam. he recommended the stage 3 twin turbo grind for my setup. got the 3/8 pushrods and dual springs as well. also picked up a melling stock pressure, high volume pump and a set of arp head studs(234-4317). just need head gaskets, flexplate, and the long block at this point to put the motor/ trans in.
__________________
12 camaro ss 427lsx, th400, f310 heads, crower shaft mounts, gpi specd solid roller, shearerfab 2k hp a/w, twin bullseye 88mm turbos, hughes pro ssx bolt together converter, holley dominator, 8.50 cert, backhalf, Ford 9", 33x17x16 tires, c16 fuel
|
10-16-2018, 05:46 PM | #184 |
Drives: 12 camaro ss, 72 chevelle, 91camaro Join Date: Dec 2013
Location: findlay,oh
Posts: 2,069
|
working on fitting the fiberglass dash. it's about 2 inches narrower than the stock dash. I ended up shoving it about 4 inches forward over stock. the plates are there to support the front until I weld in dzus plates for easy install/removal.
started putting hot/cold side parts on to get them off the floor in the shop.also a pic of my 8 month old baby showing stock camaros are good for something 😂
__________________
12 camaro ss 427lsx, th400, f310 heads, crower shaft mounts, gpi specd solid roller, shearerfab 2k hp a/w, twin bullseye 88mm turbos, hughes pro ssx bolt together converter, holley dominator, 8.50 cert, backhalf, Ford 9", 33x17x16 tires, c16 fuel
|
10-21-2018, 02:10 PM | #185 |
Drives: 12 camaro ss, 72 chevelle, 91camaro Join Date: Dec 2013
Location: findlay,oh
Posts: 2,069
|
cided to back half the car. removed the back window last night. gonna cut floor pan from the rear seat back into the trunk area. we will see as we go! stay tuned.
removed headliner, complete wiring harness, center console, airbags, and a few other things. removing the headliner took forever since the cage obstructed the bolts for a lot of things
__________________
12 camaro ss 427lsx, th400, f310 heads, crower shaft mounts, gpi specd solid roller, shearerfab 2k hp a/w, twin bullseye 88mm turbos, hughes pro ssx bolt together converter, holley dominator, 8.50 cert, backhalf, Ford 9", 33x17x16 tires, c16 fuel
Last edited by ttshovel; 10-25-2018 at 03:08 PM. |
10-26-2018, 07:56 PM | #186 |
Drives: 12 camaro ss, 72 chevelle, 91camaro Join Date: Dec 2013
Location: findlay,oh
Posts: 2,069
|
got the aerospace front drag kit in. will add pics after I install them this week.
ordered the gpi front hose kit for these brakes. along with some 6mm copper nickel line and fittings. going to redo all the factory lines and eliminate the abs module all together
__________________
12 camaro ss 427lsx, th400, f310 heads, crower shaft mounts, gpi specd solid roller, shearerfab 2k hp a/w, twin bullseye 88mm turbos, hughes pro ssx bolt together converter, holley dominator, 8.50 cert, backhalf, Ford 9", 33x17x16 tires, c16 fuel
Last edited by ttshovel; 10-27-2018 at 12:06 PM. |
10-26-2018, 08:05 PM | #187 |
Drives: 2013 Camaro SS Turbo Join Date: Apr 2014
Location: South Florida
Posts: 1,525
|
Those brakes are sexy af. What wheel/tire setup do you plan to run?
__________________
|
10-26-2018, 08:27 PM | #188 | |
Drives: 12 camaro ss, 72 chevelle, 91camaro Join Date: Dec 2013
Location: findlay,oh
Posts: 2,069
|
Quote:
tires in rear I'm looking at 32/33 by 14.5/16.5 slicks. we will see how wide I can get once i get the rear ordered
__________________
12 camaro ss 427lsx, th400, f310 heads, crower shaft mounts, gpi specd solid roller, shearerfab 2k hp a/w, twin bullseye 88mm turbos, hughes pro ssx bolt together converter, holley dominator, 8.50 cert, backhalf, Ford 9", 33x17x16 tires, c16 fuel
|
|
10-28-2018, 08:53 PM | #189 |
Drives: 12 camaro ss, 72 chevelle, 91camaro Join Date: Dec 2013
Location: findlay,oh
Posts: 2,069
|
got the brakes installed. the instructions were something to be desired from aerospace so I'll break it down for those doing it themselves.
the rotor hat to rotor bolts i found through other manufacturers get torqued anywhere from 35-40 inch lbs to 16 foot lbs. I snugged them by hand with red loctite. the brackets to factory spindle bolts get torqued to 50 foot lbs. the 9/16 thick spacers go between the bracket and spindle as shown. the rotor then gets put on the hub the caliper without pads gets installed as shown. swimming may be needed to center the rotor in the caliper. mine did not use any spacers for reference. the caliper bolts get torqued to 35 foot lbs. I did not use any loctite as the calipers are aluminum and might want to get them back off. then you can drop the pads in and install the retaining bolt using red loctite, snug this by hand as well. I hope this helps someone doing the install as I couldn't find anything useful for my questions
__________________
12 camaro ss 427lsx, th400, f310 heads, crower shaft mounts, gpi specd solid roller, shearerfab 2k hp a/w, twin bullseye 88mm turbos, hughes pro ssx bolt together converter, holley dominator, 8.50 cert, backhalf, Ford 9", 33x17x16 tires, c16 fuel
|
10-31-2018, 10:02 AM | #190 |
Drives: 12 camaro ss, 72 chevelle, 91camaro Join Date: Dec 2013
Location: findlay,oh
Posts: 2,069
|
got the rear speaker tray cut out. and 5 of the 7 dzus fasteners for the dash on
__________________
12 camaro ss 427lsx, th400, f310 heads, crower shaft mounts, gpi specd solid roller, shearerfab 2k hp a/w, twin bullseye 88mm turbos, hughes pro ssx bolt together converter, holley dominator, 8.50 cert, backhalf, Ford 9", 33x17x16 tires, c16 fuel
|
11-06-2018, 06:08 PM | #191 |
Drives: 2014 1SS/RS LS3 Join Date: Jul 2012
Location: Wisconsin
Posts: 621
|
Badass build man. Cant wait to rip into mine soon here. Not going that far tho!
__________________
2014 1SS/RS LS3 AGP TT, Custom TSP Cam, 4L80E Swap 1/4 mile- 9.53 @ 145mph
|
11-06-2018, 07:06 PM | #192 |
Drives: 12 camaro ss, 72 chevelle, 91camaro Join Date: Dec 2013
Location: findlay,oh
Posts: 2,069
|
Thanks man! appreciate it! looks like you've got a badass build going yourself!
__________________
12 camaro ss 427lsx, th400, f310 heads, crower shaft mounts, gpi specd solid roller, shearerfab 2k hp a/w, twin bullseye 88mm turbos, hughes pro ssx bolt together converter, holley dominator, 8.50 cert, backhalf, Ford 9", 33x17x16 tires, c16 fuel
|
11-09-2018, 05:59 PM | #193 | |
Drives: 2013 Camaro SS Turbo Join Date: Apr 2014
Location: South Florida
Posts: 1,525
|
Quote:
__________________
|
|
11-09-2018, 07:24 PM | #194 |
Drives: 12 camaro ss, 72 chevelle, 91camaro Join Date: Dec 2013
Location: findlay,oh
Posts: 2,069
|
lighter wheel/ tire weights. and way more options for tires
__________________
12 camaro ss 427lsx, th400, f310 heads, crower shaft mounts, gpi specd solid roller, shearerfab 2k hp a/w, twin bullseye 88mm turbos, hughes pro ssx bolt together converter, holley dominator, 8.50 cert, backhalf, Ford 9", 33x17x16 tires, c16 fuel
|
11-09-2018, 09:45 PM | #195 |
Drives: 2013 Camaro SS Turbo Join Date: Apr 2014
Location: South Florida
Posts: 1,525
|
Do you know the wheel specs for fitting a 15 up front? Weld only lists 15" wheel specs for the rear
__________________
|
11-10-2018, 12:13 AM | #196 |
Drives: 12 camaro ss, 72 chevelle, 91camaro Join Date: Dec 2013
Location: findlay,oh
Posts: 2,069
|
champion has all their technical stuff listed on their website. the inside barrel diameter is 13.125 iirc
__________________
12 camaro ss 427lsx, th400, f310 heads, crower shaft mounts, gpi specd solid roller, shearerfab 2k hp a/w, twin bullseye 88mm turbos, hughes pro ssx bolt together converter, holley dominator, 8.50 cert, backhalf, Ford 9", 33x17x16 tires, c16 fuel
|
|
|
|
|