05-18-2014, 09:20 AM | #1 |
Account Suspended
Drives: 2016 2SS Join Date: Mar 2014
Location: Palm Desert
Posts: 2,353
|
no drill license plate frame
best no drill license plate frame?
I live in CA and need to have a front license plate, but id rather not drill if i don't have to. |
05-18-2014, 09:56 AM | #2 |
Drives: 2014 1SS/RS LS3 Join Date: Jul 2012
Location: Wisconsin
Posts: 621
|
I got one from these guys and I like it. Super easy install. http://jacfab.com/products/camaro-pr...plate-bracket/
|
05-18-2014, 10:05 AM | #3 |
Drives: 2014 2SS/RS Join Date: Jan 2014
Location: Eastern Nebraska
Posts: 454
|
+1
JacFab
__________________
|
05-18-2014, 02:02 PM | #4 |
Drives: 2001 Camaro LT1 Convertible Join Date: May 2014
Location: Longmont, CO
Posts: 4
|
I used zip ties and turned the factory mount upside down. I used some felt tape where the bracket touches the paint for protection.
|
05-19-2014, 12:53 PM | #5 |
2010 2SS/RS M6
Drives: 2010 2SS/RS M6 Join Date: Jun 2010
Location: Auckland, NZ
Posts: 1,482
|
+1 for Jac Fab. I have one for my ZL1 conversion. 2 bolts underneath the bumper (already there) and done.
__________________
2/7/2014: 419 hp, 419 tq
Cosmetic: ZL1 front w/mailslot, painted stripes, powdercoated SS rims, tow hook, and full chrome delete Suspension: Pfadt subframe bushings, Pfadt rear UCA bushings, Z28 Upper control arms, Spohn trailing arms with BMR trailing arm & differential bushings, ZL1 Toe Rods and springs, Prothane radius arm inserts & steering rack bushing, Pfadt Sport front sway, FE4 conversion w/ DS rear sway, Pfadt strut brace Drivetrain: RMCR tune, CAI intake, Kooks headers, hi-flo cats & exhaust, VMAX TB, ZL1 fuel pump, LSR Tri-Ax shifter Bumblebee Racecar Build |
05-19-2014, 01:34 PM | #6 |
Drives: 2011 Camaro SS/RS 2SS Join Date: Oct 2013
Location: here
Posts: 591
|
i love my jacfab....and it gets compliments
|
05-20-2014, 05:06 AM | #7 |
Drives: 2013 SS Supercharged Convertible Join Date: May 2013
Location: SoCal
Posts: 2,714
|
JacFab
|
05-20-2014, 05:02 PM | #8 |
Drives: 2016 1LT RS Camaro; 72 Chevelle Join Date: Apr 2008
Location: Central Point, OR
Posts: 5,688
|
Thanks for the recommendations guys!
OP, I have the brackets to fit the 2014 in stock assuming you don't have any additional ground effects. Please let me know if you have any questions? |
05-20-2014, 05:24 PM | #9 |
Account Suspended
Drives: 2016 2SS Join Date: Mar 2014
Location: Palm Desert
Posts: 2,353
|
OP?
|
05-20-2014, 05:28 PM | #10 |
Drives: 2016 1LT RS Camaro; 72 Chevelle Join Date: Apr 2008
Location: Central Point, OR
Posts: 5,688
|
|
06-01-2014, 09:09 AM | #11 |
Account Suspended
Drives: 2016 2SS Join Date: Mar 2014
Location: Palm Desert
Posts: 2,353
|
Way too expensive!
I'm going to make my own |
06-01-2014, 11:41 PM | #12 |
Drives: 2011 Camaro SS/RS 2SS Join Date: Oct 2013
Location: here
Posts: 591
|
zip tie it to the lower grill
|
06-02-2014, 11:17 PM | #13 |
Drives: 2012 Camaro RS LT2 45th Join Date: Jun 2012
Location: Des Plaines, Illinois
Posts: 167
|
Just posted a new thread in the DIY section.
It shows how you can flip and use the original factory license plate holder below the bumper and not cut or drill anything. Need a few parts at the hardwares store, but will cost you about $4.00 and about ten minutes of time. Hope you can find it useful. http://www.camaro5.com/forums/showth...33#post5180933
__________________
JSTEPHEN 2012 45th Camaro RS
LED DRL - RX CATCH CAN - VTC - ROTOFAB CAI |
06-02-2014, 11:55 PM | #14 |
Account Suspended
Drives: 2016 2SS Join Date: Mar 2014
Location: Palm Desert
Posts: 2,353
|
Thank you very much!
|
|
|
|
|