You are browsing camaro5 
 |
|
07-13-2020, 01:55 PM
|
#1 |
     
|
Z28 rear suspension knuckle on a 2010 SS, SS caliper bolt on ?
Does anyone know if the Z28 rear suspension knuckles, current p/n left 23262765 and right 23262766 are bolt on pieces for a 2010 SS? I believe dimensions are the same, but the Z28 knuckle has better bushings installed. But will a rear SS/LZ1/1LE caliper bolt on ?? TIA.
__________________
RJT 2SS/RS, AAM 3.70's, MTI Sway Bars, Shifter & SS brake lines, ZLI calipers, rotors & pads, BMR Trailing & Toe Arms, rear cradle & diff bushes, Pedders XA's, Camber/Toe eccentrics, Radius arm inserts, GTO clutch reservoir, LS9 cam, Comp valve springs, Melling 10296 oil pump, CR5 timing chain, LS6 damper, CAI Cold Air Intake, ARH LT headers w/HF cats, GMPP touring axle back, Elite Engineering Catch Can, Forgeline 20x9.5 & 20x11 DS3 whls, 275/40/20 & 315/35/20 tires, 2011 Convertible spoiler, 1LE front spoiler, Lloyd "SS" Floor Mats, GM Camaro Trunk Mat, wrapped console & Grant steering wheel.
|
|
|
|
07-13-2020, 02:26 PM
|
#2 |
|
Drives: 2015 Z/22 Join Date: Aug 2015
Location: Ontario, Canada
Posts: 931
|
I believe the only bushing in the knuckle that is stiffer than the rest of the Camaro models/trims is the trailing arm bushing; might be easier to pop out the bushing if you so want it. Not sure if the knuckle (and caliper) is a direct swap but I'm guessing so since the rest of the suspension and brakes between the models is transferable (except for maybe the new style rear bar).
__________________
Overkill/Self Tuned; Mace Camshafts; K&N Typhoon Cold Air Intake; Ported 80mm Throttle Body/Intake Manifolds/Manifold Spacer; Solo Performance High-Flow Cats, Cat-back Exhaust; Vitesse Motorsports Throttle Controller; Elite Engineering E2 Catch Can; BC Racing BR Coilovers; JPSS Delrin Radius Rod Bushing Inserts, Sway Bars; Pegasus Aluminum Rear Cradle Bushings, Camber/Caster Plates; Z/28 Toe Links, Trailing Arms, Upper Control Arm Bushings, Rear Shock Mounts
|
|
|
|
|
07-13-2020, 02:30 PM
|
#3 |
  Drives: 2010 Camaro SS2,L99, LSA SC Join Date: Aug 2017
Location: Huntsville, AL
Posts: 2,155
|
I installed the 728 knuckles with those part #s on my 2010 SS with no problems.
|
|
|
|
|
07-14-2020, 10:56 PM
|
#4 |
  
Drives: 2022 1SS 1LE A10 BCD WCT+PDR Join Date: Mar 2008
Location: Johnstown, PA
Posts: 3,209
|
The answer to your question is, yes, no issues. I did the Z knuckles on my '14 1LE
__________________
2022 1SS 1LE A10 BCD WCT+PDR2014 1SS 1LE NPP RECARO SIM-SOLD1995 Z28 M6 GSC PGM-SOLD1975 NOVA COUPE 300HP 350 TH350 FLASH RED-SOLD
 Last edited by cdb95z28; 07-15-2020 at 02:01 PM. |
|
|
|
|
07-15-2020, 12:49 AM
|
#5 |
|
Account Suspended
|
As said, same, just has better bushings.
|
|
|
|
|
|
|
|
 |
|
|
