Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
TireRack
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Engine | Drivetrain | Powertrain Technical Discussions > Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons


Reply
 
Thread Tools
Old 02-22-2018, 10:15 PM   #1
Sturgill_SS
 
Sturgill_SS's Avatar
 
Drives: 2010 Camaro SS 506whp/480TQ
Join Date: Jan 2017
Location: Independence, KY
Posts: 226
Any ideas where this little guy belongs?

Any ideas??
Attached Images
 
Sturgill_SS is offline   Reply With Quote
Old 02-22-2018, 10:30 PM   #2
patternpilot

 
patternpilot's Avatar
 
Drives: 2012 2SS/RS 05 Jag S type R
Join Date: Aug 2011
Location: Tri-Cities WA.
Posts: 882
The picture is a little blurry. What were you doing when this was left over?
__________________
There's more to life than gas mileage

LS3, Whipple, Custom Comp Cam, springs, pushrods, timing set, CAI intake, Apex cold air scoop, Doug Thorley TRI-Y headers, Billet Custom Products baffled Valve covers, Mighty Mouse Catch can, ADM FPCM, ZL1 fuel pump, MSD boost-a-pump, Hex Vent hood vents, ProSport gauges(fuel pressure, AFR, Boost), Corsa, No Cats. Jannetty remote tuned, Pfadt trailing arms, all parts user installed. No Dyno yet. Manual trans. 3.45 gears.
patternpilot is offline   Reply With Quote
Old 02-22-2018, 10:33 PM   #3
Sturgill_SS
 
Sturgill_SS's Avatar
 
Drives: 2010 Camaro SS 506whp/480TQ
Join Date: Jan 2017
Location: Independence, KY
Posts: 226
Rebuilding the engine... I'm sitting here thinking, and can't figure out where this damn thing belongs! About an inch and a half in diameter. Very soft gasket
Sturgill_SS is offline   Reply With Quote
Old 02-22-2018, 10:35 PM   #4
Sturgill_SS
 
Sturgill_SS's Avatar
 
Drives: 2010 Camaro SS 506whp/480TQ
Join Date: Jan 2017
Location: Independence, KY
Posts: 226
This may be better
Attached Images
 
Sturgill_SS is offline   Reply With Quote
Old 02-22-2018, 10:48 PM   #5
Dylan1214
 
Dylan1214's Avatar
 
Drives: 2014 Camaro SS L99
Join Date: Nov 2017
Location: Michigan
Posts: 139
Old timing cover seal?
__________________
Mods: GPI VVT SS1 cam , CAI Intake, Kooks Long Tube Headers, Borla Cat Back Exhaust, BoWhite Ported Throttle Body, CHE Trunion upgrade, Elite E2 Catch Can, DynoSteve Tune.
Dylan1214 is online now   Reply With Quote
Old 02-22-2018, 11:03 PM   #6
Sturgill_SS
 
Sturgill_SS's Avatar
 
Drives: 2010 Camaro SS 506whp/480TQ
Join Date: Jan 2017
Location: Independence, KY
Posts: 226
No it's paper thin.. like a 2 piece deal. It's killing me right now lol!
Sturgill_SS is offline   Reply With Quote
Old 02-22-2018, 11:39 PM   #7
Dylan1214
 
Dylan1214's Avatar
 
Drives: 2014 Camaro SS L99
Join Date: Nov 2017
Location: Michigan
Posts: 139
Well I hope it's not important, I just finished my cam swap and found that exact piece on my floor, I thought it was old timing cover seal so I trashed it
__________________
Mods: GPI VVT SS1 cam , CAI Intake, Kooks Long Tube Headers, Borla Cat Back Exhaust, BoWhite Ported Throttle Body, CHE Trunion upgrade, Elite E2 Catch Can, DynoSteve Tune.
Dylan1214 is online now   Reply With Quote
Old 02-23-2018, 12:23 AM   #8
Sturgill_SS
 
Sturgill_SS's Avatar
 
Drives: 2010 Camaro SS 506whp/480TQ
Join Date: Jan 2017
Location: Independence, KY
Posts: 226
I hope it's not important.. I traced everything I did and couldn't find where it went. The timing cover seal is a little bigger and more durable
Sturgill_SS is offline   Reply With Quote
Old 02-23-2018, 01:23 AM   #9
hammdo
'It's an experiment'
 
hammdo's Avatar
 
Drives: [COTW 2/09/15] '11 GPI LSA SC Z/LE
Join Date: May 2014
Location: Dallas TX
Posts: 6,982
It’s a vibration/spacer/anti rotational ring for the balancer. Should be put on:

http://www.camaro5.com/forums/showpo...postcount=1474

Goes on the back of the balancer to help shim the balancer the right depth and to keep the balancer from rotating.

Also used to space the balancer:

http://www.camaro5.com/forums/showpo...&postcount=129
Http://www.camaro5.com/forums/showpo...&postcount=132
https://www.smcautoparts.com/Cranksh...538-adx012.htm
http://www.speedinc.com/shop-by-manu...on-washer.html

Buy a new one, remove the balancer to install. Need a ‘New’ balancer bolt as those are one use TTY bolts... use red loc-tite on that bolt.

FYI, grew up in Ft Wright and Erlanger...

-Don
__________________
747 RWHP 794 RWTQ
"Horsepower sells cars, torque wins races." - Enzo Ferrari
See My Build: http://www.camaro5.com/forums/showthread.php?t=385577

Last edited by hammdo; 02-23-2018 at 01:38 AM.
hammdo is online now   Reply With Quote
Old 02-23-2018, 01:29 AM   #10
Bo White


 
Bo White's Avatar
 
Drives: 2010 Summit White 1SS
Join Date: Feb 2012
Location: Vance Alabama
Posts: 6,873
Mine was not in good shape the last time it was apart. I tossed it and reassembled without it.
Bo White is offline   Reply With Quote
Old 02-23-2018, 01:45 AM   #11
Dylan1214
 
Dylan1214's Avatar
 
Drives: 2014 Camaro SS L99
Join Date: Nov 2017
Location: Michigan
Posts: 139
Quote:
Originally Posted by Bo White View Post
Mine was not in good shape the last time it was apart. I tossed it and reassembled without it.
How long did you run without?
__________________
Mods: GPI VVT SS1 cam , CAI Intake, Kooks Long Tube Headers, Borla Cat Back Exhaust, BoWhite Ported Throttle Body, CHE Trunion upgrade, Elite E2 Catch Can, DynoSteve Tune.

Last edited by Dylan1214; 02-23-2018 at 02:36 AM.
Dylan1214 is online now   Reply With Quote
Old 02-23-2018, 02:48 AM   #12
Bo White


 
Bo White's Avatar
 
Drives: 2010 Summit White 1SS
Join Date: Feb 2012
Location: Vance Alabama
Posts: 6,873
Almost 40k miles.
I double checked my alignment of the pulleys and it all looked good so I sent it! Lol
Bo White is offline   Reply With Quote
Old 02-23-2018, 03:52 AM   #13
hou30guy

 
Drives: 2011 convertible 2ss/rs
Join Date: Sep 2015
Location: Houston
Posts: 821
Thats for the crank

Sent from my SM-N950U using Tapatalk
hou30guy is offline   Reply With Quote
Old 02-23-2018, 07:54 AM   #14
go_go_gadget88
 
go_go_gadget88's Avatar
 
Drives: 2010 Camaro 2SS/RS ABM 6M
Join Date: Jul 2017
Location: Kansas
Posts: 342
Weird, I never saw this on it's own doing my swap. And my pulley got sat on a table 2 feet from car and didn't move.

Any chance mine just stayed on the pulley?
__________________
2010 Aqua Blue Metallic 2SS/RS LS3 6 Speed -- Rotofab CAI, Speed Engineering 1 7/8" Longtubes w/ cat Delete, Magnaflow competition catback, TSP 231/246 cam, TSP CNC Ported Heads, Bo White PTB, Powell Bronze Trunnion upgrade
go_go_gadget88 is offline   Reply With Quote
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:26 PM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2018, vBulletin Solutions, Inc.