12-07-2010, 07:49 AM | #1 |
Emerald Coast Camaros
|
Hood adjustments?
Hello again C5,
I have a small problem with the hood of the car. Is there a way to adjust the hieght of the hood when it is closed? The sides of the hood are right but the center front is to low. I know on older cars you could adjust it.
__________________
Had: 69' RS, 78' Z28, 98' SS Have: 2010 1RS/SS |
12-07-2010, 07:55 AM | #2 |
Drives: 10 1LT SIM; 91 B4C sleeper Z Join Date: Aug 2009
Location: Ft. Mitchell, Alabama
Posts: 7,199
|
Pop your hood and you'll see the bumpers (I guess that's the word). They're black and believe there are four. They screw in and can be backed off as needed to level the hood. Hope that helps!
__________________
Pedders Pace Car Package, Injen CAI, Flowmaster AT, AAC Lighting, ZL1 fascia/skirts, RKSport Ram Air hood, vented fenders, painted stripes (Gary's Customz), Honor and Valor badged (Thank you, John)
|
12-07-2010, 08:29 AM | #3 |
Psssssssssshhhhhhhhhhhhh!
Drives: under contruction Join Date: Nov 2009
Location: Marysville, Ohio
Posts: 12,996
|
garcmol is correct. The bumpers sit right under where the hood rests just above the radiator.
|
12-07-2010, 08:33 AM | #4 |
Emerald Coast Camaros
|
Thanks I tried that but they are either to high (won't allow hood to latch) or still to low.
__________________
Had: 69' RS, 78' Z28, 98' SS Have: 2010 1RS/SS |
12-07-2010, 08:43 AM | #5 |
Drives: 2012 ZL1 - #670 Join Date: Jun 2009
Location: Seminole, Fl.
Posts: 8,009
|
Take it to the dealer ...
__________________
|
12-07-2010, 09:36 AM | #6 |
Drives: '15 SS 1LE, '69 Z28 drag car Join Date: Dec 2009
Location: Mich
Posts: 4,482
|
Sounds like the latch needs to be finessed a bit. It does not look adjustable, two bolts mounting it. But maybe a good body guy good figure out a way to fudge it up a bit. I'd let the dealer's body shop look at it.
|
12-07-2010, 09:45 AM | #7 |
376 cubic inches of fun
|
Shim the latch?
|
12-07-2010, 11:22 AM | #8 |
Emerald Coast Camaros
|
thanks everyone..looks like I'll visit the dealer on the way home tonight.
__________________
Had: 69' RS, 78' Z28, 98' SS Have: 2010 1RS/SS |
12-07-2010, 11:42 AM | #9 |
Drives: '11 2SS/RS RJT M6 Join Date: Oct 2010
Location: Grounded in the 'Shwa
Posts: 478
|
I took a look at mine. You should have some play in the latch if you loosen the mounting bolts. How low is your hood?
If you want to do it yourself, I would make sure that you know the torque spec on the bolts before you loosen them. It's part of your front impact safety equipment. |
12-07-2010, 12:29 PM | #10 |
Drives: 10 1LT SIM; 91 B4C sleeper Z Join Date: Aug 2009
Location: Ft. Mitchell, Alabama
Posts: 7,199
|
You have one of the best fabricators/painters just down the street from you. Well, at least the same location. PM Gary's Customs, he may be able to assist you owner to owner!
__________________
Pedders Pace Car Package, Injen CAI, Flowmaster AT, AAC Lighting, ZL1 fascia/skirts, RKSport Ram Air hood, vented fenders, painted stripes (Gary's Customz), Honor and Valor badged (Thank you, John)
|
12-22-2010, 12:51 PM | #11 | |
Emerald Coast Camaros
|
Quote:
__________________
Had: 69' RS, 78' Z28, 98' SS Have: 2010 1RS/SS |
|
12-22-2010, 12:53 PM | #12 | |
Emerald Coast Camaros
|
Quote:
The dealer is going to look at it after the holidays. It even confused them when they took a quick look.
__________________
Had: 69' RS, 78' Z28, 98' SS Have: 2010 1RS/SS |
|
12-22-2010, 12:58 PM | #13 |
Drives: 2011 2SS/RS A6 Join Date: Aug 2010
Location: Middle River, Md.
Posts: 128
|
Your hood is probably right but the front bumper is off. There are 2 hex head bolts by the hood latch that will move the bumper up and down. There are also gray shims under the six push pins that hold the bumper top on (for fine adjustment). I discovered this when installing the Nite Rider LED bar. Adjust the 2 hex head bolts very slowly and recheck the hood alignment with the bumper. If these hex head bolts are mistakenly tightened down (like I did) the front bumper will be about 1/4 inch higher than the front of the hood.
__________________
JRE custom tune, AIRAID cai, VMAX spiral ported throttle body,
BORLA shorty headers, SOLO hi flo cats & mach-xl cat back, RX catch can/breather cap, MTI plug wires SPARKS SS emblems, PUTCO mailslot led, AAC led side markers, AUTOLUMINATION drl's, f/r turn sig,dome, trunk, license led's, SOUTHERN CAR PARTS sequential turn signals, BIG WORM GRAPHICS hood spears, mail slot, gills 3M CRYSTALLINE 40% window tint HURST shifter/plate, GMPARTS quarter flares RPI flat black bezels and rjt license plate frame STREET SCENE chin splitter Last edited by 2011SS; 12-22-2010 at 03:43 PM. |
12-22-2010, 01:12 PM | #14 | |
Emerald Coast Camaros
|
Quote:
Thanks again!
__________________
Had: 69' RS, 78' Z28, 98' SS Have: 2010 1RS/SS |
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
MPD1 "Z/28 style" ram air hood | Eric-MPD1.com | Exterior Parts & Accessories | 665 | 09-10-2014 06:42 AM |
Specter Werkes Camaro GTZ Extractor Hood | ACS Composite | Cosmetics and Lighting Modification Discussions | 18 | 07-02-2011 09:11 AM |
New Specter GTR Extractor Hood | ACS Composite | Exterior Parts & Accessories | 15 | 09-27-2010 08:23 PM |
custom hood, need stripes | asmith10 | Cosmetics and Lighting Modification Discussions | 2 | 08-09-2010 10:13 AM |
Anyone in California Want a Carbon Fiber hood in Trade for there OEM Hood | henri26900 | USA - California | 7 | 09-24-2009 12:19 PM |