10-08-2010, 08:10 PM | #29 |
Drives: Trailblazer SS & Camaro SS Join Date: Nov 2009
Location: North Jersey
Posts: 758
|
I hear you on the bolt for the horn, I sat there for an hour playing with that bolt trying to get it tight, finally did though without removing the bumper.
__________________
2010 Camaro 2SS/RS/LS3 -Black on Black - Kooks 1-7/8 Headers, Dyno Tuned, ADM Race CAI, QTP Cutouts, Hurst Short Throw, SJM Line Lock, Alpine PDX 1.1000, (2) Alpine Type R's, ...Soon to be cammed!
|
10-08-2010, 08:28 PM | #30 |
Drives: Yellow 2SS, 6 speed manual Join Date: Jan 2010
Location: Concord, NC
Posts: 218
|
After I removed the tire and inner fender liner, stock air box and washer bottle, I was able to reach the horn bolt without dismantling the front bumper. Sorry to hear you had it difficult Captain McFunk but glad you are pleased with the results.
__________________
Hers & His |
10-08-2010, 08:29 PM | #31 |
Drives: 2SS/RS Join Date: Sep 2008
Location: Western North Carolina
Posts: 7,182
|
Does the washer bottle have to be removed for the scoop or can it be reinstalled after the scoop is installed?
|
10-08-2010, 08:29 PM | #32 |
Account Suspended
Drives: 2010 Camaro Join Date: Feb 2010
Location: Sandy Hook, CT
Posts: 11,927
|
I have my scoop on with the CAI box as well but since the front clip was off and I had Jannetty do the install, it couldn't have been easier!
|
10-08-2010, 08:31 PM | #33 |
Drives: Yellow 2SS, 6 speed manual Join Date: Jan 2010
Location: Concord, NC
Posts: 218
|
The scoop is installed in the same place as the washer bottle and uses one of the washer bottle bolts to secure it in place. I used a washer bag - see above post link of my install.
__________________
Hers & His |
10-08-2010, 09:05 PM | #34 |
Drives: 2013 Blue Ray ZL1 Join Date: Feb 2010
Location: Phoenix, AZ
Posts: 87
|
|
10-08-2010, 09:53 PM | #35 |
Drives: Silver SS/RS, Man 6 Join Date: Apr 2009
Location: DFW area, Texas
Posts: 884
|
You only need to remove the left wheel and plastic fender liner. 5 push pins and 5 torqx screws. Then remove the washer bottle 3 13mm bolts and replace the horn bolt 10mm facing aft with the longer one provided by ADM. This will allow you to use the longer horn bolt and one of the washer bottle bolts to install. While there you trim the plastic air brake by removing a piece about 3 by 5 inches of plastic to provide the source of air thru the lower grill and up and into the airbox. You do NOT remove the front facia; unless you are installing a heritage grill. Good Luck, not difficult.
__________________
Silver 2SS/RS Man/6
CTS-V front 6-Piston Calipers, GM 3.91 Rear Gears |
10-08-2010, 10:00 PM | #36 |
Sold car...
Drives: 2010 Rally Yellow 2SS/RS #37115 Join Date: Oct 2009
Location: Manalapan, New Jersey
Posts: 2,019
|
Took me all of 2 hous to mount the scoop and relocate new water bottle. Cutting the plastic piece where the scoop goes was the hardest. Now for some headers and a tune.
__________________
Build Thread
ECS Novi 1500 Supercharged, LS3 conversion, Small blower cam, Alky Meth injection, 3:45 rear, BMR Suspension parts, 1LE Sways, Billy Boat ZL1 dual mode exhaust. |
10-09-2010, 05:12 AM | #37 |
Drives: Yellow 2SS, 6 speed manual Join Date: Jan 2010
Location: Concord, NC
Posts: 218
|
Snakestang65,
I get some grief of the bag but it is all in good fun . It is really a great application and inexpensive. Once the lid is installed, you cant even see the bag. You could always paint it black if you wanted. I also own a 68 Mustang so for me the bag was a natural and is usually a conversation starter.
__________________
Hers & His |
10-11-2010, 12:42 PM | #38 |
Drives: 2010 Camaro SS Join Date: Jun 2010
Location: Lake Charles, LA
Posts: 58
|
Has anyone installed the scoop that has a Injen CAI?
I'd like to put the scoop on, but I think my filter sits right about where the scoop is. EDIT Nevermind, after looking at another picture I see that the filter actually sits pass that. |
11-08-2010, 09:11 AM | #39 |
Camaro Owner Since 1987
Drives: 2011 2SS/RS L99 RJT Join Date: Jun 2006
Location: Lawrenceville, GA
Posts: 2,185
|
I just bought a ADM Scoop. Now I need a washer bottle location.
Bill
__________________
2011 Camaro 2SS/RS L99 RJT
CAI, Inc. Cold Air Induction;ADM Scoop Rx Catch Can;Rx Breather;Roto-Fab Washer Container VMax Ported RJT Throttle Body XSPower Headers and XSPower 3" Exhaust System Elite Engineering Tunnel Brace, Gorilla Wheel Lock System; Bear Rotors, Hawk HPS Tinted Windows 35%;EFILive Tune |
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
My Baby is home! 2SS/RS Black w/IOM | Michael_Js | Member Car Journals | 144 | 08-13-2011 04:41 PM |
******** 2 subwoofer box install pics? | Dmundz | Audio, Video, Bluetooth, Navigation, Radar, Electronics Forum | 2 | 06-03-2010 11:52 PM |
ADM Performance "Street" & "Race" intakes in stock and ready to ship! FREE SHIPPING!! | Apex Motorsports | V8 Bolt-Ons & Tunes | 23 | 05-22-2010 07:14 AM |
[COTW 4/4/10]: JRPXXII is finally DONE...SWEEEEEET | jrpxxii | Member Car Journals | 90 | 04-13-2010 10:03 PM |
BUDWEISER SHOOTOUT LINE UP | CamaroScotty | General Automotive + Other Cars Discussion | 22 | 02-07-2009 07:03 PM |