Homelink Harness - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

custommx3 · 10-23-2015, 02:01 PM

I purchased a used homelink unit and am looking for a harness to power it. It has some sort of blade style connector on it. Anyone know where I can get one relatively cheap? Anyone parting out a car?

Gen5diy has one, but I'd rather not spend 40 bucks on something that simple.

http://www.gen5diy.com/Home-Link-Har...ry=true&page=2

Jylee · 10-23-2015, 06:12 PM

I suggest to use same electical clips, it should only be a hot and ground wire to power the unit.

Jack

Low Saturn · 10-23-2015, 06:34 PM

The OEM homelink is wired to constant 12 volts, I rewired mine and tapped it into the sunroof power. That way it only has power when the ignition is on. Did this on my Suburban, Tahoe and Silverado as well. That way if someone happens to break into one of my vehicles when I'm not home, the can't open the garage door.

Just something to think about.

custommx3 · 10-25-2015, 02:36 PM

Do we know the pinouts? There are 3 connections.

stantmann · 10-25-2015, 04:40 PM

Ironic, I put mine in today. I just swapped out the overhead console with the replacement console, it came with the entire wiring harness. Worked perfectly, and programed it for my garage. If you bought the entire console, it only takes a few minutes to swap it out.

stantmann · 10-25-2015, 04:57 PM

Check this thread out Darth Martel made me one that I never used. I just tried to hunt it down, damn, nowhere to be found. It's basically a harness that goes over the 3 connectors in the pic above. The other side is open, just + and - (red and black). You can do this yourself though, just read the thread above. Not sure if Darth is still making them, last time I checked he sold his 5th gen, but he is still active on the site. http://www.camaro5.com/forums/member.php?u=10046

Low Saturn · 10-25-2015, 04:59 PM

Quote:

Originally Posted by custommx3

Do we know the pinouts? There are 3 connections.

If its typical GM its:

Pin A: 12 volts
Pin B: Illumination
Pin C: Ground

Pin B would be unused.

custommx3 · 10-26-2015, 10:57 AM

Thank you guys SO much! This has helped a lot! I sent him a message to see if I could get a harness from him. if Not I at least have the pinouts to try and make my own.

baddmans · 11-08-2015, 12:48 PM

I have the 2 wire harness with the plug I got from Darth Martel. In fact I have the whole overhead console black with GDO buttons and the 2 wire harness with plug, to splice into positive and negative wires. No sunroof buttons in the overhead console.

custommx3 · 11-09-2015, 08:01 PM

Stantmann sold me a spare one he had, Thanks man!

I painted the one I had that was pulled from a salvage car that was a bit faded. I haven't spliced into the wires yet, but I did test out the harness and homelink module. Work flawlessly.

Now I have to figure out what's hot and what's ground in the '14 mirror.

bjsmusic · 12-15-2018, 09:40 PM

The wire harness is available from Gen5DIY
The power is on the left, ground on right, nothing goes in the middle, harness goes to fuse block, nice set up, worth the price. The overhead console with wires is the way to go, but hard to find,because most salvage yards cut the wires:

10-23-2015, 02:01 PM	#1
custommx3 Drives: 2017 2SS, 2023 3LT RS, 2011 2LT RS Join Date: Aug 2014 Location: Memphis Posts: 360 View My Garage	Homelink Harness I purchased a used homelink unit and am looking for a harness to power it. It has some sort of blade style connector on it. Anyone know where I can get one relatively cheap? Anyone parting out a car? Gen5diy has one, but I'd rather not spend 40 bucks on something that simple. http://www.gen5diy.com/Home-Link-Har...ry=true&page=2

10-23-2015, 06:34 PM	#3
Low Saturn Drives: 2011 Camaro 2SS/RS Join Date: Oct 2013 Location: San Jose, California Posts: 1,371	The OEM homelink is wired to constant 12 volts, I rewired mine and tapped it into the sunroof power. That way it only has power when the ignition is on. Did this on my Suburban, Tahoe and Silverado as well. That way if someone happens to break into one of my vehicles when I'm not home, the can't open the garage door. Just something to think about. __________________

10-25-2015, 02:36 PM	#4
custommx3 Drives: 2017 2SS, 2023 3LT RS, 2011 2LT RS Join Date: Aug 2014 Location: Memphis Posts: 360 View My Garage	Do we know the pinouts? There are 3 connections. Attached Images

10-25-2015, 04:40 PM	#5
stantmann Drives: 2012 Camaro Convertible LT Join Date: Aug 2012 Location: Sedona, AZ Posts: 15	Ironic, I put mine in today. I just swapped out the overhead console with the replacement console, it came with the entire wiring harness. Worked perfectly, and programed it for my garage. If you bought the entire console, it only takes a few minutes to swap it out. __________________ 2012 1LT Standard: Convertible, Fog lights, Steering wheel controls, USB/Ipod/Auxillary ports, backup cam on mirror. Mods: 20" OEM Chrome Wheels, HUD, HomeLink, SS leather seats, tow package with Ohio State hitch cover, CCFL Angel Eyes, SS Frontend, sequential signal lights, auxillary guages, Knight Rider Oracle scanner lights.

10-25-2015, 04:57 PM	#6
stantmann Drives: 2012 Camaro Convertible LT Join Date: Aug 2012 Location: Sedona, AZ Posts: 15	Check this thread out Darth Martel made me one that I never used. I just tried to hunt it down, damn, nowhere to be found. It's basically a harness that goes over the 3 connectors in the pic above. The other side is open, just + and - (red and black). You can do this yourself though, just read the thread above. Not sure if Darth is still making them, last time I checked he sold his 5th gen, but he is still active on the site. http://www.camaro5.com/forums/member.php?u=10046 __________________ 2012 1LT Standard: Convertible, Fog lights, Steering wheel controls, USB/Ipod/Auxillary ports, backup cam on mirror. Mods: 20" OEM Chrome Wheels, HUD, HomeLink, SS leather seats, tow package with Ohio State hitch cover, CCFL Angel Eyes, SS Frontend, sequential signal lights, auxillary guages, Knight Rider Oracle scanner lights. Last edited by stantmann; 10-25-2015 at 06:00 PM.

10-23-2015, 06:12 PM	#2
Jylee Drives: 2012 2LT Join Date: Aug 2013 Location: Sugarland, TX Posts: 96	I suggest to use same electical clips, it should only be a hot and ground wire to power the unit. Jack

10-26-2015, 10:57 AM	#8
custommx3 Drives: 2017 2SS, 2023 3LT RS, 2011 2LT RS Join Date: Aug 2014 Location: Memphis Posts: 360 View My Garage	Thank you guys SO much! This has helped a lot! I sent him a message to see if I could get a harness from him. if Not I at least have the pinouts to try and make my own.

11-08-2015, 12:48 PM	#9
baddmans Banned Drives: 2015 Camaro 1LT Join Date: May 2010 Location: Lansing, Michigan Posts: 267	I have the 2 wire harness with the plug I got from Darth Martel. In fact I have the whole overhead console black with GDO buttons and the 2 wire harness with plug, to splice into positive and negative wires. No sunroof buttons in the overhead console. Last edited by baddmans; 11-09-2015 at 11:20 AM. Reason: More info.

11-09-2015, 08:01 PM	#10
custommx3 Drives: 2017 2SS, 2023 3LT RS, 2011 2LT RS Join Date: Aug 2014 Location: Memphis Posts: 360 View My Garage	Stantmann sold me a spare one he had, Thanks man! I painted the one I had that was pulled from a salvage car that was a bit faded. I haven't spliced into the wires yet, but I did test out the harness and homelink module. Work flawlessly. Now I have to figure out what's hot and what's ground in the '14 mirror.

12-15-2018, 09:40 PM	#11
bjsmusic Drives: 2011 Camero RS infernal Orange , Join Date: Dec 2018 Location: Cleveland,Ohio Posts: 9 View My Garage	Home link The wire harness is available from Gen5DIY The power is on the left, ground on right, nothing goes in the middle, harness goes to fuse block, nice set up, worth the price. The overhead console with wires is the way to go, but hard to find,because most salvage yards cut the wires: