08-07-2014, 05:45 AM | #239 |
Drives: 99 Camaro; 2010 Camaro 2SS/RS Join Date: Nov 2009
Location: louisiana
Posts: 1,965
|
does it work with the whipple?
__________________
2018 Camaro SS A8 Edelbrock 2650 FBO 93 octane 9.54@144 Pump E 9.59@152
2010 Camaro Stock bottom end with 46,000+miles JRE remote tuning Whipple A6 and Drive it to and from the track 9.46@146 |
08-07-2014, 07:15 AM | #240 |
If you install with out a rain tray yes. I still have not seen anyone successfully install with a Whipple. Maybe someone else Knows.....
http://www.slponline.com/product/620...extractor.html |
|
08-08-2014, 10:21 AM | #241 |
|
I like the look of the ACS TLE vent, I PM's them and it sounds like they may be making something for the 2010-2013 hoods.... I hope so!
__________________
|
08-20-2014, 06:28 PM | #242 |
So-Cal Camaro Invasion
Drives: Autobot Join Date: Feb 2013
Location: Tha Valley
Posts: 693
|
finally got around to snapping some pics of the final product..
__________________
|
08-20-2014, 06:41 PM | #243 |
Under construction...
Drives: Black 2012 2SS Join Date: Jul 2014
Location: Uvalde Tx
Posts: 246
|
Looks ****ing epic, love the car. What's the difficulty on this project?
__________________
2012 2SS/RS, mods coming soon
|
08-20-2014, 08:11 PM | #244 |
08-20-2014, 09:44 PM | #245 | |
So-Cal Camaro Invasion
Drives: Autobot Join Date: Feb 2013
Location: Tha Valley
Posts: 693
|
Quote:
Thanks!!
__________________
|
|
08-21-2014, 09:30 AM | #246 |
KaBoom1701
Drives: 13' ZL1 Red M6 Join Date: Dec 2012
Location: I.E. SoCal (Yucaipa)
Posts: 8,630
|
So I have a question for everyone that has done this...
I track my car at speeds over 100-110mph on the road course. Has anyone who has this hood vent been at those speeds and can confirm the stability of the hood vent and hood. Don't really want to do this and have my hood flopping up and down while I'm at Fontana Speedway. Thx
__________________
Mods:
Roto-Fab Intake, WW Res. kit & Big Gulp Air Scoop, Elite Catch Can, ATI Super Damper & 18% OD Pulley, LF Idler pulley bracket, Metco CC breather, ID850 Injectors, Stainless Power Headers w/ ceramic coating, TR71X Spark Plugs, JMS Fuel Pump Booster, Bo White TB, Tuned by Ted @ Jannetty Racing, Ron Davis HX, D3 Reservoir, Pfadt 1" Springs, Moreno Camber Plates, ZL1 Addons Splitter guard washers, Tow Hook kit & rock guards, Hurst Shifter Billet Plus 6 Speed Short Shifter, ZL1 DRL lighting harness, ZL1 Recaro Seats. |
08-21-2014, 12:21 PM | #247 | |
So-Cal Camaro Invasion
Drives: Autobot Join Date: Feb 2013
Location: Tha Valley
Posts: 693
|
Quote:
__________________
|
|
08-21-2014, 10:17 PM | #248 | |
KaBoom1701
Drives: 13' ZL1 Red M6 Join Date: Dec 2012
Location: I.E. SoCal (Yucaipa)
Posts: 8,630
|
Quote:
Ok, Thx for the feedback!
__________________
Mods:
Roto-Fab Intake, WW Res. kit & Big Gulp Air Scoop, Elite Catch Can, ATI Super Damper & 18% OD Pulley, LF Idler pulley bracket, Metco CC breather, ID850 Injectors, Stainless Power Headers w/ ceramic coating, TR71X Spark Plugs, JMS Fuel Pump Booster, Bo White TB, Tuned by Ted @ Jannetty Racing, Ron Davis HX, D3 Reservoir, Pfadt 1" Springs, Moreno Camber Plates, ZL1 Addons Splitter guard washers, Tow Hook kit & rock guards, Hurst Shifter Billet Plus 6 Speed Short Shifter, ZL1 DRL lighting harness, ZL1 Recaro Seats. |
|
08-21-2014, 10:54 PM | #249 |
Master ASE, GM, LSX Tech.
Drives: 2010 Camaro SS Join Date: Oct 2012
Location: Austin, TX
Posts: 1,034
|
I recently finished up installing the vent on my 2010. I made the template from cardboard. With the vent upside down you can place the cut cardboard and see how your cut line will look. There is a decent margin for error. I used a electric cut off die grinder with a 6" wheel. I masked off the hood and fenders with tape, cover the engine and car with blankets. Looking back it would have been better to remove the hood and cut away from the car.
My advice is measure and re-measure then measure again. Only cut once. I went to my local Chevy dealer and measured a new Camaro on the lot to get the placement measurements. It is 16 1/4 from the back of the hood to the edge of the vent. However that is not your cutting line. The center left/right is easy with the line in the hood. There are 6 mounting studs on the vent, I made my own brackets to secure. With the insulation cut they are all hidden. I did not use the factory under hood water deflector. Defeats the entire purpose of venting out under hood heat. Over all it was an easy install that came out great. Anyone considering this just remember to measure and make sure your template is accurate.
__________________
2010 2SSRS A6, Custom Pat G. Cam, WCCH Cylinder Heads, Kooks Headers/Exhaust, BTR Valvetrain, Fluidampr 25% UDP, All Engine ARP bolts, Flex-a-lite radiator/Trans cooler, Yank converter, PFADT Suspension, ADM Race Intake/Scoop, Torq tow hook, CFD auto shifter, Dynojet AFR gauge, Aeroforce scan gauge, Brake Performance rotors/pads
Prothane bushings, ZL1 wheels, spoiler, Z/28 wickerbill, 1LE Aero/Suspension Package, Anderson Composites COPO Carbon Fiber Hood, LED lighting, Elite Catch Can, Improved Racing oil pan baffle, crank scraper, windage tray 480 RWHP 452 RWTQ + Nitrous Express 150 Shot |
08-22-2014, 10:07 AM | #250 | |
KaBoom1701
Drives: 13' ZL1 Red M6 Join Date: Dec 2012
Location: I.E. SoCal (Yucaipa)
Posts: 8,630
|
Quote:
__________________
Mods:
Roto-Fab Intake, WW Res. kit & Big Gulp Air Scoop, Elite Catch Can, ATI Super Damper & 18% OD Pulley, LF Idler pulley bracket, Metco CC breather, ID850 Injectors, Stainless Power Headers w/ ceramic coating, TR71X Spark Plugs, JMS Fuel Pump Booster, Bo White TB, Tuned by Ted @ Jannetty Racing, Ron Davis HX, D3 Reservoir, Pfadt 1" Springs, Moreno Camber Plates, ZL1 Addons Splitter guard washers, Tow Hook kit & rock guards, Hurst Shifter Billet Plus 6 Speed Short Shifter, ZL1 DRL lighting harness, ZL1 Recaro Seats. |
|
08-22-2014, 11:42 AM | #251 |
Drives: 15 Lexus RCF, 17 Vette Grand Sport Join Date: Apr 2013
Location: South Florida
Posts: 549
|
Anyone have a templete that I could use?? I am receiving my part tomorrow??
__________________
2013 Summit 1SS 1LE w/NPP, SW 1 7/8" Long Tube Headers, CAI Intake, Ported TB, Cammotion 224/232 113 LSA, BTR Valvetrain, Melling Oil Pump, 468 HP 423, Apex Catch Can, Tank Plates, RPM 4 Point Roll Bar with SCCA/NASA Cross Brace, Schroth 6 Point Han's Harness, OMP WRC Front Seats, F.M.T Trailing Arms, F.M.T Solid Aluminum Subframe Bushings, Moreno Motorsports Camber Plates, BMR Bushings Front and Rear, Essex/AP Racing Radi-Cal Endurance Front Brakes, Quantum Brake Cooling Ducts, ZL1 Rockers, ZL1 Air Deflectors, Heritage Grill, Pfadt Springs.
|
08-22-2014, 02:34 PM | #252 |
Jan
Drives: 2010 Camaro 1LT Red Jewel tintcoat Join Date: May 2010
Location: Springfield, TN
Posts: 16,225
|
Dang! You guys just made me add one more mod to the list!
__________________
|
|
|
Thread Tools | |
|
|