04-18-2013, 12:44 PM | #1 |
Drives: 2013 2SS M6 Join Date: Oct 2012
Location: Tallahassee, Fl
Posts: 205
|
Is this normal? Gap in Dash Trim around gauge
I just noticed this today. The car is practically brand new. The black molding of the dash feels hard and solid (not warped) but I can (with a little pressure) push the silver accent piece closer, but nothing clips or holds it in at all. Is this normal?
|
04-18-2013, 12:45 PM | #2 |
Wifey Lover
Drives: 2013 Crystal Red 2LT/RS Join Date: Nov 2011
Location: Bastrop, Texas
Posts: 1,541
|
Mine is flush and it's a 2013
__________________
|
04-18-2013, 12:56 PM | #3 |
knows 2 facts about ducks
Drives: ...and they're both wrong Join Date: Aug 2009
Location: The HMS Invincible
Posts: 25,072
|
I have the exact same issue. Turned out the part the retaining tab (one on the speedometer) locked into on the dash had broken off.
And the dash is one solid piece, so only way to fix it would be to get a new dash or McGyver it. |
04-18-2013, 01:09 PM | #4 |
Older Than Dirt
Drives: 2010 & 2013 Camaros Join Date: Apr 2010
Location: Aiken, SC
Posts: 4,563
|
Warranty? Take it in. Let them fix it. Unless you don't trust them to do it right.
__________________
2010 2SS TE, 1 of 822/2013 Camaro ZL1 vert, 1 of 54
|
04-18-2013, 01:20 PM | #5 |
Drives: '11 2SS, '11 C6 GS, '04 MDX Join Date: Feb 2012
Location: Kearney, MO
Posts: 2,845
|
|
04-18-2013, 01:56 PM | #6 |
Drives: 2013 2SS M6 Join Date: Oct 2012
Location: Tallahassee, Fl
Posts: 205
|
Looks like the car is going to the dealer... *sigh*
|
04-18-2013, 06:54 PM | #7 |
Drives: 2010 Inferno Orange 2SS/RS Join Date: Apr 2010
Location: Clermont, IN
Posts: 3,297
|
SUPERGLUE!
__________________
2010 Inferno Orange 2SS/RS M6 Black Leather, Sun Roof, OBX Headers, Borla touring axle back, Cold Air Inductions CAI , non synthetic fluids, BMR total bushing upgrade/1" lowering springs, DSE 32mm rear sway bar. GM fe4 shocks/struts/LCA's, AAM 3.91 diff, Vertini RFS1.8 20x9 +30. Conti ExtremeContact Sport 275/35/20. sjm autoprod ABL dash kit. Mike Norris tuned 413/419.
Avenging Orange: 43 years of not buying into the Hype........and damn proud of it!! https://youtu.be/9JD9it6SmB8 https://youtu.be/xmelTlEzI34 KICKING CANCERS ASS SINCE 2015!! |
04-18-2013, 07:04 PM | #8 |
Drives: 2011 Camaro 2SS/RS Join Date: Jul 2011
Location: Wittenberg, Wisconsin
Posts: 701
|
Mine was like that when I put it back on after taking it off to do my ABL installation. Turns out all I needed to do was readjust it. One of the clips wasn't going in right But if you haven't touched it, take it to the dealer. Just in case something might be broken
__________________
My Build Thread:http://www.camaro5.com/forums/showthread.php?t=287531 |
04-18-2013, 08:28 PM | #9 |
ITCRNRS
Drives: 2018 ZL1 1LE Join Date: Jun 2012
Location: Wichita KS
Posts: 1,575
|
Ours has the same issue dealer tried replacing the bezel and it looked the same then told us they would need to replace the whole dash I said no thanks didnt want a rattling dash this early in its life
__________________
2018 ZL1 1LE Ordered 6/29/17 Built 11/6/17 Delivered 12/7/17, Summit White, PDR, NAV, https://www.youtube.com/c/tylerpotter
SOLD: 2014 Summit White 1LE 2SS/RS, Recaros, NPP, NAV, KONI Yellow's SOLD: 2012 Black 2LT/RS, Fully 1LE swapped, Brembo swap |
04-18-2013, 10:05 PM | #10 |
knows 2 facts about ducks
Drives: ...and they're both wrong Join Date: Aug 2009
Location: The HMS Invincible
Posts: 25,072
|
Yea unfortunately if the tab part on the dash is broken the only fix is to replace the dash.
|
04-18-2013, 10:46 PM | #11 |
Drives: 2013 2SS M6 Join Date: Oct 2012
Location: Tallahassee, Fl
Posts: 205
|
Well, if they have to replace the whole dash, and I plan on doing it eventually, then it would make sense to still do it while I have my bumper-bumper warranty. I am assuming that doing it after it is expired would be several thousand dollars?
My biggest concern, as ICT said above, is that replacing the dash to fix this one small aesthetic issue will cause other problems/rattling later on. |
04-22-2013, 10:40 AM | #12 |
Drives: 2013 1SS Panther 1993 B4C Join Date: Jul 2012
Location: Methuen, MA
Posts: 214
|
I just took mine out of storage for a quick spin last week (had been parked since November) when the weather was kind of decent and I had some time. Bang, bezel is just starting to pull away, 355 miles. NOT happy.
__________________
2013 1SS M6 Panther
1993 B4C M6 1993 B4C A4 |
04-22-2013, 10:46 AM | #13 |
Drives: COTW 8/29/11 2010 CAMARO Join Date: Jul 2009
Location: HOMELESS
Posts: 10,010
|
Your not going to have any issues let the dealership do it many have taken out there dash to do mods and no one has complained about issues after including me..
|
04-22-2013, 03:02 PM | #14 |
Drives: GM Vehicles Join Date: Jun 2010
Location: Michigan
Posts: 9,328
|
Hello NoleLife,
Sorry you have to be inconvenienced with this issue. I understand the frustration of unexpected visits to the dealer. I would like to step in and help you if at all possible. Do you have a preferred dealer? If so, I will be happy to contact them on your behave about this issue and also set up a time for you to visit your that dealer. I can also locate one nearest you if you don't have one currently. Reggie B. Chevrolet Customer Care.
__________________
For information on the GM Privacy Statement, please visit http://www.gm.com/privacy-statement.html
|
|
|
|
|