11-16-2023, 01:53 PM | #57 |
Drives: 2016 Camaro rs V6 Join Date: Nov 2023
Location: Windsor Ontario Canada
Posts: 1
|
I have a 2016 Camaro rt 3.6l v6 engine with the 6 piston Brembo brakes. I cannot find the rotors for this. They are 14.5"/368mm. the biggest rotors I have found on several sites is 13.58/345mm. Does anyone have a clue as to where I could find these.
Thank You in advance for your time and help. |
11-16-2023, 02:11 PM | #58 | |
Drives: 2010 Turbo LS3 Join Date: Dec 2009
Location: Palm Bay, FL
Posts: 2,736
|
Quote:
__________________
2010 SS - On3 kit with downpipe cutout, CTR 78/80, CompCam 239/251 620/632 122+4, E85, Z28 suspension and ZL1 diff with Outlaw axles. Gen6 ZL1/1LE brakes.
2011 Vert - 416/w 230/236 .612/.602 115lsa, 1LE suspension w/32mm rear bar. Z28 diff. ZL1 brakes. |
|
11-16-2023, 02:23 PM | #59 | |
Drives: 2010 Turbo LS3 Join Date: Dec 2009
Location: Palm Bay, FL
Posts: 2,736
|
Quote:
__________________
2010 SS - On3 kit with downpipe cutout, CTR 78/80, CompCam 239/251 620/632 122+4, E85, Z28 suspension and ZL1 diff with Outlaw axles. Gen6 ZL1/1LE brakes.
2011 Vert - 416/w 230/236 .612/.602 115lsa, 1LE suspension w/32mm rear bar. Z28 diff. ZL1 brakes. |
|
11-16-2023, 10:39 PM | #60 | |
"Cam Only"
|
Quote:
Where'd you order your brake lines and how easy was the swap if you did it on jack stands in your garage?
__________________
2013 AGM Camaro 2SS/RS M6 | LSA Blower, 2.5" pulley, 10% lower, FIC1000's, Fore Innovations Twin Pump fuel system w/ Flex Fuel, CMS Custom Grind Cam, Kooks 1 7/8" headers w/ catless off-road pipes, NPP Exhaust, 3.91's, JLT ZL1 Intake, Prospeed Heat Exchanger | Pfadt Suspension, 1LE Sway Bars | DSS 1000hp axles |
Tuned by Ryne @ CMS E85: 734rwhp/636rwtq (mustang dyno) |
|
11-17-2023, 03:38 PM | #61 |
Drives: 2010 Camaro 2SS L99 Join Date: Apr 2023
Location: Olympia, WA
Posts: 460
|
I got some stainless braided goodridge lines on eBay, you have to be careful on there, but you can find some good deals even on new stuff, like the brand new set of rear HPS pads I bought for half the price, even had to message the guy and make sure he was selling full set of 4, price was so low I was half expecting it to be a scam. One thing with lines and such is I would recomend you cap off the holes as you work, I let all the fluid drain completely and spent way too long bleeding all the bubbled out, especially with that ABS module sitting higher then the reservoir, some have done it with zero issues but it was pain in the neck for me. Otherwise it's pretty easy even on jack stands since you're just dealing with the wheel wells, I also had ton of leaks at the connection to the hardlines, learned to tighten those harder then you would think.
__________________
Behind every scratch is a story on what not to do, and my car has a lot of stories.
|
11-17-2023, 04:48 PM | #62 | |
Quote:
My brake lines came from KNS Brakes. Got the Goodridge brake lines for the ZL1. As for the install, it was very easy and I did mine on jack stands. The hardest part was bleeding the brakes and that is not hard, just a pain doing it alone.
__________________
2013 1SS/1LE
Corsa Extreme cat-back, Speed Engineering LT Headers with black ceramic coating, C7 Z06 Front Brake Upgrade, Mishimoto Oil Cooler, BMR Tunnel Brace, Mishimoto Oil Catch Can, MSD Plug Wires, Mishimoto Radiator and Hoses. |
||
11-17-2023, 11:44 PM | #63 | ||
"Cam Only"
|
Quote:
Quote:
__________________
2013 AGM Camaro 2SS/RS M6 | LSA Blower, 2.5" pulley, 10% lower, FIC1000's, Fore Innovations Twin Pump fuel system w/ Flex Fuel, CMS Custom Grind Cam, Kooks 1 7/8" headers w/ catless off-road pipes, NPP Exhaust, 3.91's, JLT ZL1 Intake, Prospeed Heat Exchanger | Pfadt Suspension, 1LE Sway Bars | DSS 1000hp axles |
Tuned by Ryne @ CMS E85: 734rwhp/636rwtq (mustang dyno) |
||
|
|
|
|