11-21-2019, 07:51 AM | #1 |
Space Coast Camaros
Drives: 2012 Camaro Vert Join Date: Sep 2011
Location: Palm Bay , FL
Posts: 1,280
|
Do I really need better axles?
Do I really need better axles?
Got 2012 SS auto with Twin Turbos. only 10 PSI and about 650wrhp. I dont race at track and would never put drag's on it. No issue letting the tires spin I dont have any issues now. other than one axle boot has been cracked for years and grease been coming out. I am upgrading Diff to AAM 3.91 gears and Detroit Truetrac POSI. I was going to just get new OEM axles, to replace bad boot one and might as well do both for the price of $370 shipped. So my question is do i really need 1,000HP axles? or will the OEM be ok with the new 3.91's? i was thinking i could always go better axles in future if needed. But when doing Diff i wanted to do it right the first time.
__________________
|
11-21-2019, 08:25 AM | #2 |
Drives: 2010 SS 2SS M6 Join Date: Aug 2016
Location: Smithsburg, Md.
Posts: 2,446
|
Been using 1LE axles(larger outer CV) off of ebay for $200 used for over 3 yrs with lots of trips to the track usin dr's and mostly 1.7 60' and lots of hwy miles too...no probs.
I also upgraded to 3.91's and have a 6M which hits the rear harder than auto. make sure to replace the axle seals at this time too! cheap insur so to answer you Q and based on your driving spec's above you should be fine...tho you must be replacing the rear's frequently right? l8tr PEACE
__________________
2010 SS 2SS M6 - Tune by RDP dynoSteve!(Woot) - Daily Driver - 150K! - All work by me...
|
11-21-2019, 09:05 AM | #3 | |
Space Coast Camaros
Drives: 2012 Camaro Vert Join Date: Sep 2011
Location: Palm Bay , FL
Posts: 1,280
|
Quote:
this should be it? ---> 1LE Axles PN 22806796 and 22806795 Seals and bearings all getting replaced when doing diff. I only Replaced the tires once. (315/35R20 Continental Extreme DWS) back in 2013 lol still got them. but its getting time to replace again. So i think i will be fine. And thanks for feedback! Last edited by KalCorp; 11-21-2019 at 09:44 AM. |
|
11-21-2019, 09:11 AM | #4 |
Account Suspended
Drives: 2013 Sparkly Red One Join Date: Dec 2018
Location: Hospitality State
Posts: 2,558
|
Probably better to replace suspension parts to prevent wheel hop. Contact BMR for recommendations.
|
11-21-2019, 10:22 AM | #5 | |
Space Coast Camaros
Drives: 2012 Camaro Vert Join Date: Sep 2011
Location: Palm Bay , FL
Posts: 1,280
|
Quote:
But i think i might replace the BMR Diff bushings (Black) looks like they are going bad. will know more when it take Diff out. Might get the BMR red ones this time. also got this from someone. its the 1LE axles 1LE LH Axle - 22806795 1LE RH Axle - 22806796 1LE Axle Nut - 11611234 (x2) Washer for the hub end, 11611965 (x2) Anyone done this before? is this correct? Should be ok for me and under $400 and not $1200 for 1khp axles. |
|
11-22-2019, 01:28 PM | #6 |
Drives: 2014 SS Convertible Join Date: Jun 2015
Location: Michigan
Posts: 175
|
If your car is lower look at offset diff bushings to help the axle angles.
__________________
Engine: LSA Conversion, Ported Heads, 1 7/8 headers, VMS 2.5 Cam, Roto Fab intake, ADM Scoop. BMR engine mounts, 3.91
628/525 Suspension: Koni orange, (BMR everything) 1" drop springs, toe rods, trailer arms, non adjustable LCR, FE4 sway bars, sub frame connectors, delrin sub frame bushing and upper control arm bushings. Front bushings. |
11-22-2019, 01:43 PM | #7 | |
Space Coast Camaros
Drives: 2012 Camaro Vert Join Date: Sep 2011
Location: Palm Bay , FL
Posts: 1,280
|
Quote:
Yes its as low as you can get static now. But I am looking into a Airlift package So driving might be normal height or little lower. Also might get a used set of DSS 1000hp axles. i have to check if its needed for them. |
|
11-22-2019, 11:55 PM | #8 |
Drives: 2011 2SS Join Date: Mar 2015
Location: Arlington, Texas
Posts: 1,333
|
I run 1le axles. I’m similar if not a little more horsepower and I drag race with 17’s and drag radials. Haven’t broken them yet! Lol. They’ll fit any SS. As far as I know all SS’s have the same diff, manual or auto, so all the axles (auto, manual, 1/le) are interchangeable. Good upgrade without spending an arm and a leg
__________________
2011 SS L99
LSA Supercharger, BTR Stage 3 PDS Cam, Yank 3200SS, Weapon X Stage 2 intake, LSA Heads, Flex Fuel, Ported throttle body, Speed Engineering Headers, NOWEEDS, ZL1 fuel pump, DSX AUX Pump, ID-1050X injectors, 3” pipe to NPP mufflers, 3.91 gears |
11-24-2019, 07:10 PM | #9 |
Drives: 2014 1ss camaro Join Date: Jul 2017
Location: missouri
Posts: 705
|
better axles
thanks frankwjr, I also was looking for an alternative to stock SS axles this is the second time you've helped me and ive listened to you and your voice of experience. thanks frank. the oldman........
|
11-25-2019, 07:31 AM | #10 |
GPI Sales Consultant
|
I'll chime in as well - if you're not going on the drag strip with sticky tires, and you know how to close the throttle if it starts to wheelhop on the street - then you don't have much to worry about. I like to think of the stock axle as a fuse, protecting more expensive parts (like the diff). I definitely wouldn't worry about it - stay with stock and/or stock replacement and have fun!
__________________
GPI Max Package 2.0: Brodix BR7 heads/GPI porting, MAX3 cam, ST2116LSR, BSR Max Lift rockers, LS7 LSXR with 103mm TB, Vararam OTR, Mcleod RXT, G-Force/Strange 9" IRS setup with 4.63 gear. 551whp, 11.1@124mph.
Got a question about a GPI product? Feel free to shoot me a message! |
11-25-2019, 07:37 AM | #11 |
Space Coast Camaros
Drives: 2012 Camaro Vert Join Date: Sep 2011
Location: Palm Bay , FL
Posts: 1,280
|
Thanks everyone!
Hard to get OEM axles right now damn strike issues. and DSS ones are 6 month Back order i hear. lol Going to update the Diff and do Air Ride. so trying to get all the parts so I only have to remove stuff once. |
11-25-2019, 08:13 AM | #12 |
Space Coast Camaros
Drives: 2012 Camaro Vert Join Date: Sep 2011
Location: Palm Bay , FL
Posts: 1,280
|
Looks like the Left (22806795) is on back order from GM. Everything else they can get.
Damn. :-( 1LE LH Axle - 22806795 1LE RH Axle - 22806796 1LE Axle Nut - 11611234 (x2) Washer for the hub end, 11611965 (x2) |
11-25-2019, 08:23 AM | #13 | |
Drives: 2010 SS 2SS M6 Join Date: Aug 2016
Location: Smithsburg, Md.
Posts: 2,446
|
Quote:
ur welcome bro!
__________________
2010 SS 2SS M6 - Tune by RDP dynoSteve!(Woot) - Daily Driver - 150K! - All work by me...
|
|
11-26-2019, 08:18 PM | #14 |
Drives: 2014 1ss camaro Join Date: Jul 2017
Location: missouri
Posts: 705
|
ordered mine this morning also, now snowball effect takes over, toes,and boxed arms in the works. might go with true track and 33;91s
|
|
|
|
|