05-04-2020, 11:07 AM | #1 |
Drives: 13' 1LE Join Date: Apr 2012
Location: Canada
Posts: 2,640
|
Ever heard 7900 rpm LS3 on a dyno?
**clutch is slipping at 7000***
Heres the dyno video. Description says it all. 568rwhp@ 7250. Dyno could not pick up the rpm signal so the dyno did stop early, even if the car actually went to 7900. Ill be back next sunday with hopefully 580+rwhp. https://youtu.be/-bYzmGNH3NM
__________________
13' 1LE
Old setup: TSP 231-236/Tick 660/.105 PR, UDP, SW LT 2'' & HFC, stock NPP & H pipe, VR-DRX CAI, air scoop, Goertz1 manifold, 102mm BBK, 26" Toyo DRs, Forgestars R17x10 & F18x8, rear seat delete, remote Pat G tune Autocal, 7400 limiter, Spec Mini Twin. 91oct. 11.90@122.3, 0-60ft 2.0 / 11.99@123.6, 0-60ft 2.1 DA+819 ...519RWHP SAE Solid roller SBE LS3, FED, LLSR, 91oct, 605rwhp N/A. Tuned by Pat G. Build by me. Last edited by WHAMMO; 05-07-2020 at 09:48 PM. Reason: Clutch slipping.. |
05-04-2020, 11:11 AM | #2 |
Drives: 13' 1LE Join Date: Apr 2012
Location: Canada
Posts: 2,640
|
Dyno sheet
__________________
13' 1LE
Old setup: TSP 231-236/Tick 660/.105 PR, UDP, SW LT 2'' & HFC, stock NPP & H pipe, VR-DRX CAI, air scoop, Goertz1 manifold, 102mm BBK, 26" Toyo DRs, Forgestars R17x10 & F18x8, rear seat delete, remote Pat G tune Autocal, 7400 limiter, Spec Mini Twin. 91oct. 11.90@122.3, 0-60ft 2.0 / 11.99@123.6, 0-60ft 2.1 DA+819 ...519RWHP SAE Solid roller SBE LS3, FED, LLSR, 91oct, 605rwhp N/A. Tuned by Pat G. Build by me. |
05-04-2020, 11:57 AM | #3 |
Drives: 2015 1LE Join Date: Oct 2015
Location: Cleveland, OH
Posts: 1,485
|
Very nice! Looks like a great combo you put together, nice flat curve from 5-8k.
__________________
2015 1LE, TSP 225/236 113+3, VMAX Throttle Body, CAI with race scoop, GPI Ported Intake, Land Speed Stage 2 Heads, 1-7/8 headers, NPP exhaust, 25% Fluidampr, LT1-S Monster Clutch, 485 RWHP & 444 TQ
|
05-04-2020, 12:01 PM | #4 |
|
Sounds great johnny! I think it will get to 580s for sure.
__________________
2010 C6 JET STREAM BLUE
BOLT ONS TO THE EXTREME, GPI 281cc HEADS, Darth_V8r SPEC CAM, FAST 102 INTAKE, CRANK SCRAPER, QUARTER MASTER 7.25" CLUTCH, RPM 3.90 STAGE II DIF, Z51 Gear Set AND E85 Best ET 10.58 @ 131.8 stock heads and stock cam 453/445 SAE 10.62@134.82 GPI 281CC Heads, SS4 Cam and X1 Intake Best 1/8 6.80@105.75 Best MPH 134.82 |
05-04-2020, 12:17 PM | #5 |
Drives: 2014 1SS/1LE Join Date: Nov 2015
Location: Louisville, KY
Posts: 826
|
So what mechanical limitation did you have to overcome to rev that high? My Whipple is still climbing hard at 7,000 but I'm not ready to rev it more than that.
__________________
830 WHP 700 WTQ, Whipple 2.9 @ 13lbs Boost, Flex Fuel Tune by Blevins Tuning, LSA SBE, 3.5 GripTec, ATI LS3 Damper, AFR 260cc Mongoose, ARP Studs, Yella Terra Ultralites, Johnson 2110R, BTR PDS Stage 3, Melling 10355, Improved Racing Baffle, ID1050X, DSX Triple Fuel Pump, RotoFab CAI, NW 103mm TB, Stainless Works 1-7/8" LTH to 3" Speed Eng w/ X-pipe to NPP, Powermaster 9509 XS, Detroit Speed Motor Mounts, MGW, Monster LT1-S, ZL1 Calipers, DBA Rotors & Pads, Bilstein B6 Struts & Shocks, BMR 1.25" Drop Springs & Adj Rear Bar, Pegasus Solid Bushings, Z/28 Wheels, other misc parts.
|
05-04-2020, 12:24 PM | #6 | |
Drives: 13' 1LE Join Date: Apr 2012
Location: Canada
Posts: 2,640
|
Quote:
-Isky linked solid red zone lifters -1209x PAC with ti retainers -T&D adj rockers -short runner manifold that will support this rpm -good heads (ls3 are good for that but ptv sucks) -a big cam -biggest pushrod youcan fit. 3/8 here
__________________
13' 1LE
Old setup: TSP 231-236/Tick 660/.105 PR, UDP, SW LT 2'' & HFC, stock NPP & H pipe, VR-DRX CAI, air scoop, Goertz1 manifold, 102mm BBK, 26" Toyo DRs, Forgestars R17x10 & F18x8, rear seat delete, remote Pat G tune Autocal, 7400 limiter, Spec Mini Twin. 91oct. 11.90@122.3, 0-60ft 2.0 / 11.99@123.6, 0-60ft 2.1 DA+819 ...519RWHP SAE Solid roller SBE LS3, FED, LLSR, 91oct, 605rwhp N/A. Tuned by Pat G. Build by me. |
|
05-04-2020, 12:27 PM | #7 |
Drives: 13' 1LE Join Date: Apr 2012
Location: Canada
Posts: 2,640
|
We cannot see past 7250, but I bet its still going strong
__________________
13' 1LE
Old setup: TSP 231-236/Tick 660/.105 PR, UDP, SW LT 2'' & HFC, stock NPP & H pipe, VR-DRX CAI, air scoop, Goertz1 manifold, 102mm BBK, 26" Toyo DRs, Forgestars R17x10 & F18x8, rear seat delete, remote Pat G tune Autocal, 7400 limiter, Spec Mini Twin. 91oct. 11.90@122.3, 0-60ft 2.0 / 11.99@123.6, 0-60ft 2.1 DA+819 ...519RWHP SAE Solid roller SBE LS3, FED, LLSR, 91oct, 605rwhp N/A. Tuned by Pat G. Build by me. |
05-04-2020, 02:14 PM | #8 |
Drives: 2010 Camaro SS/RS Join Date: Mar 2014
Location: somewhere in MD
Posts: 4,883
|
Sounds awesome and nice results!
__________________
2010 2SS/RS
Z/28 intake, NW, FAST 102, speed engineering LT's, some exhaust, ATI -10% pulley, GM flex fuel injectors, DSX flex fuel sensor, MGW shifter, HP Tuners, some suspension work, stickers and a little weight loss. 12.63 @113.53 |
05-04-2020, 03:11 PM | #9 |
Drives: 2015 Summit White 2SS 1LE Join Date: Feb 2012
Location: Vance Alabama
Posts: 8,019
|
I've heard 8500 or so on stock bottom end.
|
05-04-2020, 03:24 PM | #10 |
Drives: 13' 1LE Join Date: Apr 2012
Location: Canada
Posts: 2,640
|
I try not to push my luck too much. I want the carto survive a bit, before going with another engine...
__________________
13' 1LE
Old setup: TSP 231-236/Tick 660/.105 PR, UDP, SW LT 2'' & HFC, stock NPP & H pipe, VR-DRX CAI, air scoop, Goertz1 manifold, 102mm BBK, 26" Toyo DRs, Forgestars R17x10 & F18x8, rear seat delete, remote Pat G tune Autocal, 7400 limiter, Spec Mini Twin. 91oct. 11.90@122.3, 0-60ft 2.0 / 11.99@123.6, 0-60ft 2.1 DA+819 ...519RWHP SAE Solid roller SBE LS3, FED, LLSR, 91oct, 605rwhp N/A. Tuned by Pat G. Build by me. |
05-04-2020, 03:51 PM | #11 | |
Drives: 2014 1SS/1LE Join Date: Nov 2015
Location: Louisville, KY
Posts: 826
|
Quote:
Sent from my Pixel XL using Tapatalk
__________________
830 WHP 700 WTQ, Whipple 2.9 @ 13lbs Boost, Flex Fuel Tune by Blevins Tuning, LSA SBE, 3.5 GripTec, ATI LS3 Damper, AFR 260cc Mongoose, ARP Studs, Yella Terra Ultralites, Johnson 2110R, BTR PDS Stage 3, Melling 10355, Improved Racing Baffle, ID1050X, DSX Triple Fuel Pump, RotoFab CAI, NW 103mm TB, Stainless Works 1-7/8" LTH to 3" Speed Eng w/ X-pipe to NPP, Powermaster 9509 XS, Detroit Speed Motor Mounts, MGW, Monster LT1-S, ZL1 Calipers, DBA Rotors & Pads, Bilstein B6 Struts & Shocks, BMR 1.25" Drop Springs & Adj Rear Bar, Pegasus Solid Bushings, Z/28 Wheels, other misc parts.
|
|
05-04-2020, 04:00 PM | #12 |
Drives: 2015 Summit White 2SS 1LE Join Date: Feb 2012
Location: Vance Alabama
Posts: 8,019
|
I want mine to live too. That's why my limiter is at 7500
|
05-04-2020, 05:54 PM | #13 |
Drives: 13' 1LE Join Date: Apr 2012
Location: Canada
Posts: 2,640
|
Uhmm...up the limiter?! What springs you run? My valvetrain components are made for higher rpm. You have good stuff too but its not the same purpose.
__________________
13' 1LE
Old setup: TSP 231-236/Tick 660/.105 PR, UDP, SW LT 2'' & HFC, stock NPP & H pipe, VR-DRX CAI, air scoop, Goertz1 manifold, 102mm BBK, 26" Toyo DRs, Forgestars R17x10 & F18x8, rear seat delete, remote Pat G tune Autocal, 7400 limiter, Spec Mini Twin. 91oct. 11.90@122.3, 0-60ft 2.0 / 11.99@123.6, 0-60ft 2.1 DA+819 ...519RWHP SAE Solid roller SBE LS3, FED, LLSR, 91oct, 605rwhp N/A. Tuned by Pat G. Build by me. |
05-04-2020, 07:41 PM | #14 | |
Drives: 2014 1SS/1LE Join Date: Nov 2015
Location: Louisville, KY
Posts: 826
|
Quote:
Sent from my Pixel XL using Tapatalk
__________________
830 WHP 700 WTQ, Whipple 2.9 @ 13lbs Boost, Flex Fuel Tune by Blevins Tuning, LSA SBE, 3.5 GripTec, ATI LS3 Damper, AFR 260cc Mongoose, ARP Studs, Yella Terra Ultralites, Johnson 2110R, BTR PDS Stage 3, Melling 10355, Improved Racing Baffle, ID1050X, DSX Triple Fuel Pump, RotoFab CAI, NW 103mm TB, Stainless Works 1-7/8" LTH to 3" Speed Eng w/ X-pipe to NPP, Powermaster 9509 XS, Detroit Speed Motor Mounts, MGW, Monster LT1-S, ZL1 Calipers, DBA Rotors & Pads, Bilstein B6 Struts & Shocks, BMR 1.25" Drop Springs & Adj Rear Bar, Pegasus Solid Bushings, Z/28 Wheels, other misc parts.
|
|
|
|
|
|