Homepage Garage Wiki Register Social Groups Calendar Search Today's Posts Mark Forums Read
#Camaro6
Go Back   CAMARO6 > Engine | Drivetrain | Powertrain Technical Discussions > V8 LT1 Engine, Exhaust, and Bolt-Ons


Bigwormgraphix


Post Reply
 
Thread Tools
Old 08-28-2019, 05:02 PM   #1
Gonzo719
 
Drives: 2017 Camaro SS
Join Date: Jan 2018
Location: Colorado
Posts: 34
CEL with catback

Hi I recently installed an AWE Tuning track edition catback with AWE link pipes that replace the secondary cats I’ve put about 500 miles on the system.

I got a CEL hooked up an OBD2 reader the code is P0420 catalyst system efficiency below threshold bank 1. Did some research and most say O2 sensor looking at the info from the reader both banks 1 and 2 #1 O2 sensors have no voltage while both banks #2 sensors have voltage.

Was wondering if others have experienced this with the O2 sensors not having voltage after installing a new exhaust system any info would be greatly appreciated Thank You
Attached Images
    
Gonzo719 is offline   Reply With Quote
Old 08-28-2019, 05:11 PM   #2
Joshinator99


 
Joshinator99's Avatar
 
Drives: 2017 Camaro 2SS A8
Join Date: Aug 2018
Location: Petersham MA
Posts: 4,701
Sounds like the sensors did not get reconnected after installation. The connectors are in a tough spot from the factory, to be fair to your installer.
__________________
2017 Chevy Camaro 2SS A8 Whipple 3.0, Mast Black Label heads, Fore triple in-tank pumps, 112mm TB, LPE +52% injectors, LPE BB HPFP, 15” conversion 1059 WHP/944 WTQ, 9.48@150
Joshinator99 is online now   Reply With Quote
Old 08-28-2019, 05:48 PM   #3
Gonzo719
 
Drives: 2017 Camaro SS
Join Date: Jan 2018
Location: Colorado
Posts: 34
I did the install myself didn’t discount those sensors so I don’t understand why they wouldn’t have any voltage
Gonzo719 is offline   Reply With Quote
Old 08-28-2019, 06:00 PM   #4
NA18CamaroSS
 
NA18CamaroSS's Avatar
 
Drives: 2018 Chevrolet Camaro 2SS 1LE 6M
Join Date: Jul 2019
Location: California
Posts: 283
If the sensors are connected, look for damage to the wiring and connectors. The sensor itself might also have been damaged.
__________________
Bolt-ons.
NA18CamaroSS is offline   Reply With Quote
Old 08-28-2019, 11:58 PM   #5
BruceWayne1LE
 
BruceWayne1LE's Avatar
 
Drives: 2018 Camaro SS 1LE M6
Join Date: Oct 2018
Location: Northern California
Posts: 345
Very possible that you could have pulled a wire loose in the O2 harness. Resistance test those bad boys. Or just bite the bullet and buy new sensors. ALSO I thee codes when I did my MBRP. Checks for leaks mainly that weird carbon ring on the driver side and the o-ring gasket on the passenger.
__________________
Camaro 2SS 1LE, MBRP Catback, Mishimoto Catch Can, Rotofab dry, TSP1 7/8” headers,DSX FF, Pray ported MSD, 95mm TB
492WHP 473WTQ
BruceWayne1LE is offline   Reply With Quote
Old 09-07-2019, 10:14 PM   #6
Gonzo719
 
Drives: 2017 Camaro SS
Join Date: Jan 2018
Location: Colorado
Posts: 34
Replaced both 02 sensors codes cleared was running good put around 500 or so miles on the car sense replacing the sensors now got a CEL again same thing no voltage on sensors 1 both banks any info on why this is happened would be greatly appreciated
Gonzo719 is offline   Reply With Quote
Old 09-15-2019, 10:02 PM   #7
Chris C 1SS 1LE
 
Chris C 1SS 1LE's Avatar
 
Drives: 2017 1LE
Join Date: Nov 2017
Location: Brooks, GA
Posts: 697
It's a very very small leak. I have I it. Comes on and I just reset it. I've no measure any voltage. Dealer says they'll Dix it. Put that little wire gasket on again. I used this but did a poor job. Many use successfully.

Drivers side where pipe slips on behind primary cat.
Attached Images
 
__________________
'17 Bright Yellow 1LE. PDR, STB, !CAGS
Borla 60606, 11925. Tony Mamo ported TB, ROTOFAB, !Sound Tube

Last edited by Chris C 1SS 1LE; 09-15-2019 at 10:04 PM. Reason: Detail
Chris C 1SS 1LE is offline   Reply With Quote
Old 09-16-2019, 12:07 PM   #8
gmw0181
 
gmw0181's Avatar
 
Drives: 2017 Camaro 2SS A8
Join Date: Dec 2017
Location: Ohio
Posts: 137
Quote:
Originally Posted by Gonzo719 View Post
Hi I recently installed an AWE Tuning track edition catback with AWE link pipes that replace the secondary cats I’ve put about 500 miles on the system.

I got a CEL hooked up an OBD2 reader the code is P0420 catalyst system efficiency below threshold bank 1. Did some research and most say O2 sensor looking at the info from the reader both banks 1 and 2 #1 O2 sensors have no voltage while both banks #2 sensors have voltage.

Was wondering if others have experienced this with the O2 sensors not having voltage after installing a new exhaust system any info would be greatly appreciated Thank You
My guess from experience is an exhaust leak on the driver side where it connects to the first cat. My Stainless works did the same thing.
I fought with it for a few months and gave up and installed Headers and high flow cats. No problems now.
gmw0181 is offline   Reply With Quote
Old 09-17-2019, 05:35 PM   #9
asrautox
 
Drives: 2017 SS 1LE
Join Date: Sep 2011
Location: Los Angeles
Posts: 154
Had this same issue with my 2nd cat delete catback. Tried resealing it a few times, but it kept coming back. After some research it appears that others with this issue actually had a bad cat. Took it to the dealer and they replaced my drivers side cat under warranty and problem was resolved.
__________________
2017 1SS 1LE - Eibach Springs | Pray IM | Katech TB | Borla 60606 | Corsa Extreme | E85 Flex Tune
asrautox is online now   Reply With Quote
Old 09-17-2019, 08:01 PM   #10
Gonzo719
 
Drives: 2017 Camaro SS
Join Date: Jan 2018
Location: Colorado
Posts: 34
Thanks for the help on this issue looking at doing headers so will need a tune thanks again
Gonzo719 is offline   Reply With Quote
Old 09-19-2019, 07:40 AM   #11
Tazz3069
 
Tazz3069's Avatar
 
Drives: 2016 Camaro 2SS
Join Date: Jan 2016
Location: Las Vegas, Nevada
Posts: 338
Quote:
Originally Posted by Gonzo719 View Post
Hi I recently installed an AWE Tuning track edition catback with AWE link pipes that replace the secondary cats I’ve put about 500 miles on the system.

I got a CEL hooked up an OBD2 reader the code is P0420 catalyst system efficiency below threshold bank 1. Did some research and most say O2 sensor looking at the info from the reader both banks 1 and 2 #1 O2 sensors have no voltage while both banks #2 sensors have voltage.

Was wondering if others have experienced this with the O2 sensors not having voltage after installing a new exhaust system any info would be greatly appreciated Thank You

Mine did the same thing, when I installed my Stainless Works Cat Back. I got it tuned and no more issues.

If the system, you installed, eliminates the secondary cats, then yes you will need a tune.
__________________

2016 Camaro 2SS "Black Widow"
Tazz3069 is offline   Reply With Quote
Old 09-19-2019, 03:23 PM   #12
oOKhanhOo
 
Drives: 2018 SS 1LE
Join Date: Sep 2018
Location: Ohio
Posts: 143
Quote:
Originally Posted by Tazz3069 View Post
Mine did the same thing, when I installed my Stainless Works Cat Back. I got it tuned and no more issues.

If the system, you installed, eliminates the secondary cats, then yes you will need a tune.
You will only need a tune if you have an automatic SS because it will delete the AFM valves by the rear axle.

I have a manual, installed the AWE catback w/o secondary cat delete. Same as OP. No CEL nor tune needed.

Secondary cats aren't monitored. OP most likely have a small leak right at the Catback and/or has an Automatic transmission
oOKhanhOo is offline   Reply With Quote
Old 09-20-2019, 02:10 AM   #13
Gonzo719
 
Drives: 2017 Camaro SS
Join Date: Jan 2018
Location: Colorado
Posts: 34
I have the M6 so didn’t think a tune was necessary doing a cat back I’ve seen lots of videos and read lots of posts with people removing the secondary cats with no issues went through and torqued everything can’t find any leaks like asrautox said maybe a bad primary cat
Gonzo719 is offline   Reply With Quote
Old 09-20-2019, 07:19 AM   #14
artey34
 
artey34's Avatar
 
Drives: 2018 Camaro 2SS 1LE - Hyper Blue
Join Date: Aug 2018
Location: Michigan
Posts: 441
Had same code with AWE Catback. Need to put muffler paste on the joint connecting the PLP and Primary Cat Outlet. Once I did that, cleared the code, no more issue
artey34 is offline   Reply With Quote
 
Post Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:29 AM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.