Technostalgia LED Tail Lights - Page 3 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

78Z2812TBD · 02-29-2012, 12:42 PM

Glad yours all work. I installed mine a few weeks ago in my vert (seriously challenging to get those lower nuts on) but I had 3 LEDs on the outer drivers side assembly that won't light at all. Todd is supposed to be sending me a replacement assembly, but I'm not really looking forward to changing that out - it was tough to begin with, now there are more wires in that tiny area to deal with. But they do look nice. I wired a small switch in for the show mode and mounted it to the top of the rear carper liner on the drivers side where it can't get bumped.

bulllett · 02-29-2012, 01:41 PM

So, the wife loves the blinkers and lights. I haven't seen the wiring, but is there anyway to keep that first flash of lights out of the brake lights?

dodojoe · 02-29-2012, 02:19 PM

That would be beyond my knowledge! Sorry.

78Z2812TBD · 03-01-2012, 09:16 PM

There are a couple switches inside each lamp assembly. One is used to turn on/off the rapid-fire brake lights, one turns on/off the sequential turn signals. These must be set the way you want them to operate before installing them in the car. Oh - I got my replacement assembly in the mail today - thanks Todd. Now to be in town to do the replacement...

LIV4MUDDIN · 03-01-2012, 09:27 PM

They take a little work but the results are great especially when another camaro owner sees yours and has lots of questions.

2001ragtop · 03-02-2012, 01:17 PM

and that will pass inspection ?

those look awesome.

LIV4MUDDIN · 03-02-2012, 02:56 PM

They passed here in MS. I believe they are DOT approved.

Tom D · 03-02-2012, 03:04 PM

Mine are suppose to arrive today. Can't wait to start this mod.

GearHeadPeter · 03-02-2012, 03:04 PM

Quote:

Originally Posted by 2001ragtop

and that will pass inspection ?

those look awesome.

Yes they are, and I love mine for over 1 year now.

Pkrimmer · 03-03-2012, 01:33 PM

Mine are working fine and no trouble install except getting the nuts back on. I did pull off one lamp bulb connect from insde the housing so be careful not to pull on the hard trying to get them in. Here is a link to mine

Tom D · 03-04-2012, 05:54 PM

Got mine in yesterday and I will say the directions they send make the job very easy. Won't post movie since its just like evryone elses. The hardest part was the tight fit for my hands. They look awesome. Now my back end flashes just like the LED's in and around my engine.

Thanks Apex. Nice packaging and delivered as promissed.

Apex Motorsports · 03-04-2012, 06:50 PM

Quote:

Originally Posted by Tom D

Got mine in yesterday and I will say the directions they send make the job very easy. Won't post movie since its just like evryone elses. The hardest part was the tight fit for my hands. They look awesome. Now my back end flashes just like the LED's in and around my engine.

Thanks Apex. Nice packaging and delivered as promissed.

Thank you for your order and the feedback.

foo.fighter · 06-23-2014, 07:16 AM

did you hear back from them CreativeDawn? im not going to order unless you got em lol

v1k1ng421 · 06-24-2014, 04:28 AM

Most of the websites I found these on listed them as "out of stock", "no longer available", etc. I finally found them on RicksCamaros.com and the web page said, "Ships direct from manufacturer. Allow additional time for delivery." so i made the mistake of thinking they were "available"; that was over 7 weeks ago and they still haven't shipped from the manufacturer. The last I heard from the vendor, they were supposed to ship "the week of June 23rd" (this week). I'm a little nervous because I'm in the military and will be leaving for a 3 month deployment in less than 4 weeks. I may be speaking too soon (they may arrive so that I can get them installed before I deploy), but I'm feeling like I should've just ordered a set of Spyder LED tail lights from Phastek with their sequential wiring harness. At least I would've had all my lighting upgrades completed by now without the worry and still would've had some nice, unique tail lights.

03-02-2012, 03:04 PM	#36
Tom D Drives: 10 Camaro SS/RS RJT Join Date: Dec 2009 Location: Ventura, Ca Posts: 415 View My Garage	Mine are suppose to arrive today. Can't wait to start this mod. __________________ 2010 2SS/RS RJT, ADM CAI, Borla Shorties, Borla "S" Cat Back, Edelbrock E-Force Supercharger, GMS Wires, GMS Rear Trailing Arms, GMS Rotors, GMS End Links, GMS Tunnel Brace, GMS Rear Tie Rods, GMS 1G Suspension Package, GMS Stage 3 CNC ported heads, GMS Spec'd R12 Custom Ground Camshaft, Snow Meth Injection, GMS Custom Tuned, Norris Catch Can, MTI Brake Lines, Pfadt Coilovers, Sway Bars, Camber Kit, and Rear LCA Reinforcement, , AAC Footwell, Trunk, DRL and Dome LED Lighting, Technostalgia Tail Lights, RED B/A Pedals, Kompression Custom Wheels with Nitto tires, 621RWHP/584RWTQ

03-04-2012, 05:54 PM	#39
Tom D Drives: 10 Camaro SS/RS RJT Join Date: Dec 2009 Location: Ventura, Ca Posts: 415 View My Garage	Got mine in yesterday and I will say the directions they send make the job very easy. Won't post movie since its just like evryone elses. The hardest part was the tight fit for my hands. They look awesome. Now my back end flashes just like the LED's in and around my engine. Thanks Apex. Nice packaging and delivered as promissed. __________________ 2010 2SS/RS RJT, ADM CAI, Borla Shorties, Borla "S" Cat Back, Edelbrock E-Force Supercharger, GMS Wires, GMS Rear Trailing Arms, GMS Rotors, GMS End Links, GMS Tunnel Brace, GMS Rear Tie Rods, GMS 1G Suspension Package, GMS Stage 3 CNC ported heads, GMS Spec'd R12 Custom Ground Camshaft, Snow Meth Injection, GMS Custom Tuned, Norris Catch Can, MTI Brake Lines, Pfadt Coilovers, Sway Bars, Camber Kit, and Rear LCA Reinforcement, , AAC Footwell, Trunk, DRL and Dome LED Lighting, Technostalgia Tail Lights, RED B/A Pedals, Kompression Custom Wheels with Nitto tires, 621RWHP/584RWTQ

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Legality of running technostalgia tail lights on street?	jph2275	Cosmetics and Lighting Modification Discussions	14	03-03-2012 11:37 AM
led tail lights	tpower	Cosmetics and Lighting Modification Discussions	7	07-17-2011 06:54 PM
ANY PROBLEMS INSTALLING THE LED TAIL LIGHTS ?	carguy50	Cosmetics and Lighting Modification Discussions	3	12-21-2010 10:58 AM
LED Tail lights	69er	Cosmetics and Lighting Modification Discussions	16	12-17-2009 01:31 PM

02-29-2012, 12:42 PM	#29
78Z2812TBD Drives: 2012 45th 2SS vert Join Date: Sep 2011 Location: St Paul Texas Posts: 107 View My Garage	Glad yours all work. I installed mine a few weeks ago in my vert (seriously challenging to get those lower nuts on) but I had 3 LEDs on the outer drivers side assembly that won't light at all. Todd is supposed to be sending me a replacement assembly, but I'm not really looking forward to changing that out - it was tough to begin with, now there are more wires in that tiny area to deal with. But they do look nice. I wired a small switch in for the show mode and mounted it to the top of the rear carper liner on the drivers side where it can't get bumped.

02-29-2012, 01:41 PM	#30
bulllett Drives: 2012 Camaro Convertible Join Date: Jun 2011 Location: East Hampton, CT Posts: 421	So, the wife loves the blinkers and lights. I haven't seen the wiring, but is there anyway to keep that first flash of lights out of the brake lights?

02-29-2012, 02:19 PM	#31
dodojoe Drives: 2011 SS RS Camaro Convertible-VR Join Date: Mar 2011 Location: Bowling Green KY Posts: 189	That would be beyond my knowledge! Sorry.

03-01-2012, 09:16 PM	#32
78Z2812TBD Drives: 2012 45th 2SS vert Join Date: Sep 2011 Location: St Paul Texas Posts: 107 View My Garage	There are a couple switches inside each lamp assembly. One is used to turn on/off the rapid-fire brake lights, one turns on/off the sequential turn signals. These must be set the way you want them to operate before installing them in the car. Oh - I got my replacement assembly in the mail today - thanks Todd. Now to be in town to do the replacement...

03-01-2012, 09:27 PM	#33
LIV4MUDDIN Drives: 2020 Camaro 2SS Join Date: Aug 2011 Location: Olive Branch MS Posts: 347 View My Garage	They take a little work but the results are great especially when another camaro owner sees yours and has lots of questions.

03-02-2012, 01:17 PM	#34
2001ragtop Drives: V8 american car Join Date: Aug 2006 Location: Dallas, Tx Posts: 1,417	and that will pass inspection ? those look awesome.

03-02-2012, 02:56 PM	#35
LIV4MUDDIN Drives: 2020 Camaro 2SS Join Date: Aug 2011 Location: Olive Branch MS Posts: 347 View My Garage	They passed here in MS. I believe they are DOT approved.

06-23-2014, 07:16 AM	#41
foo.fighter Drives: 2013 Camaro 2SS IOM M6 Join Date: Mar 2013 Location: Toronto Posts: 342 View My Garage	did you hear back from them CreativeDawn? im not going to order unless you got em lol

06-24-2014, 04:28 AM	#42
v1k1ng421 Drives: 2013 1LS Join Date: Feb 2013 Location: Las Vegas Posts: 20	Most of the websites I found these on listed them as "out of stock", "no longer available", etc. I finally found them on RicksCamaros.com and the web page said, "Ships direct from manufacturer. Allow additional time for delivery." so i made the mistake of thinking they were "available"; that was over 7 weeks ago and they still haven't shipped from the manufacturer. The last I heard from the vendor, they were supposed to ship "the week of June 23rd" (this week). I'm a little nervous because I'm in the military and will be leaving for a 3 month deployment in less than 4 weeks. I may be speaking too soon (they may arrive so that I can get them installed before I deploy), but I'm feeling like I should've just ordered a set of Spyder LED tail lights from Phastek with their sequential wiring harness. At least I would've had all my lighting upgrades completed by now without the worry and still would've had some nice, unique tail lights.