08-08-2014, 08:53 PM | #183 |
BLCSWAN
Drives: Camaro ZL1, Toyota 4Runner Join Date: Jun 2012
Location: Maryland
Posts: 100
|
Thanks DrkPhx. Wow Vroom, well hopefully this one is your last one. Do you know if this replacement is a different design than the other two you had?
__________________
2012 Black Camaro ZL1, Red Rx Can, Black CAI
|
08-08-2014, 10:31 PM | #184 |
Drives: 2013 Camaro ZL1 Join Date: Oct 2012
Location: SF Bay Area
Posts: 325
|
Yeah, should be the new one with the solid isolator I hope. My current one is starting to make the same bearing noise my first one did. Can't believe they didn't catch this before releasing for production....
|
08-12-2014, 05:27 PM | #185 |
BLCSWAN
Drives: Camaro ZL1, Toyota 4Runner Join Date: Jun 2012
Location: Maryland
Posts: 100
|
__________________
2012 Black Camaro ZL1, Red Rx Can, Black CAI
|
08-16-2014, 03:14 PM | #186 |
MSG,Retired US. ARMY
Drives: 2012 ZL1, 11 XC 90, 15 BMW 328i SW Join Date: Feb 2012
Location: Germany
Posts: 233
|
A month later I am back on the road. New engine, and SC install at no cost to me. Needs to go back because I the clutch is not rift shift fine under normal acceleration. Under hard acceleration it will not shift to the next it only grinds the gear.
Now to break it in and get the 2.55 pulley installed and the LG. motorsports cam kit. Should take me to about 690-700 rwhp. Then it will be time to stable her for winter. Thank you GM for your outstanding support.
__________________
My build site:
http://www.camaro5.com/forums/showthread.php?t=276256 2012 Camaro ZL1 #151, GCN, Dyno results 701 RWHP Mods; 2.55 Pulley, CAI, LG Cam Package Ti Springs and 9G2X Cam, RX Can, KDI Heat exchanger, Hurst shifter, Orcale Ghosted marker lights, Kooks Long tube headers with Cats deletes and Tuned by Kraftwerks, Pedders 1 inch lowering Springs, Front and rear sway bars, Rear cradle bushing, BMR Trailing arms and toe rods. |
08-16-2014, 04:44 PM | #187 |
H-Town Camaro Club Member
Drives: 17 Hyper Blue Metallic KLR-ZL1 Join Date: May 2009
Location: Pearland Tx.
Posts: 2,035
|
Great to hear you are rolling again. Atleast some what. Hopefully they can fix or replace the tranny.
__________________
|
08-21-2014, 07:08 PM | #188 |
Drives: 2013 Victory Red Camaro ZL1 Join Date: May 2012
Location: Pennsville, NJ
Posts: 53
|
Can anyone recommend a good GM dealer in the tri state area, N.J., Del, PA or Maryland to take my 2013 ZL1 in to replace the supercharger without getting the runaround ?
|
08-22-2014, 11:53 AM | #189 | |
Drives: 2014 CRT Convertible ZL1 Join Date: Nov 2013
Location: NW NJ
Posts: 377
|
Quote:
Sent from my XT1080 using Tapatalk |
|
08-22-2014, 08:41 PM | #190 | |
Drives: GM Vehicles Join Date: Jun 2010
Location: Michigan
Posts: 9,328
|
Quote:
Andraya (assisting William) Chevrolet Customer Care |
|
08-22-2014, 09:40 PM | #191 | |
Drives: Possibly a 1LE in the near future. Join Date: Oct 2012
Location: US Of A
Posts: 436
|
Quote:
|
|
08-23-2014, 07:35 AM | #192 | |
Drives: 2014 CRT Convertible ZL1 Join Date: Nov 2013
Location: NW NJ
Posts: 377
|
Quote:
Sent from my Nexus 7 using Tapatalk |
|
08-24-2014, 08:25 AM | #193 |
Drives: Possibly a 1LE in the near future. Join Date: Oct 2012
Location: US Of A
Posts: 436
|
Too bad your giving a lame attempt at an answer with someone who has first hand experience working with "Customer Service" at chevrolet. The staff there is a waste of space and they are nothing more than a middle man. So yes...If you are not capable of talking and can not explain the issue with your vehicle to your dealership then maybe they could be of help...otherwise don't waste your time.
|
08-28-2014, 04:27 PM | #194 |
My 2014 ZL1 was manufactured in September 2013. Will my car have the supercharger fix already done to it?
|
|
08-28-2014, 11:05 PM | #195 |
Drives: 2013 ZL1 Join Date: Oct 2013
Location: Nor Cal
Posts: 481
|
Just had mine done today.. Took them just 5 or 6 hours.. Everything went perfect with my dealer.. Maita Chevy in Sacramento Ca.
__________________
2013 Silver ZL1
|
08-28-2014, 11:26 PM | #196 | |
Drives: 2014 ZL1 M6 Join Date: Jul 2014
Location: Virginia
Posts: 493
|
Quote:
The fix started in november 2013. Tony
__________________
2014 ZL1 M6
Bone stock, for now! 2001 Z28 M6 !cags, !air, FTP 85mm Lid, Z06 85mm MAF, P&P TB !4x4, Strano Springs, Strano Sways, Koni 4/4s, Watts Link ARH LTs, ARH catted Y, SLP catback with Dual/Dual Muffler, SLP CME and Valance OE Wheels Machined Face C5 DDs, 18x10.5s, with 295/35-18s on all 4 corners! 352rwhp and 366rwtq |
|
|
|
|
|