07-11-2016, 01:25 AM | #1 |
Drives: '14 1LS Join Date: Apr 2014
Location: Mandeville
Posts: 2,166
|
C7 z06 replicas
Does anyone know if they will fit a fifth gem? I can get them in 19x10 from WCC. Would I need a spacer? I'd rather not use one of I don't have to. I hear spacers can be dangerous on road course cars.
Sent from my iPhone using Tapatalk
__________________
Patiently waiting for my 2023 SS 1LE |
07-11-2016, 08:33 AM | #2 |
Svt lol
Drives: 2011 ss inferno orange blown Join Date: Jan 2012
Location: Topeka
Posts: 2,312
|
What offset? My guess would be 5X offset which means you would need a spacer. How big would have to be determined.
__________________
plasti dip is not a mod.......and a cold air intake doesn't make you fast!
|
07-11-2016, 04:53 PM | #3 |
|
If its a 19x10 it would be a ET 30 most likely if its a front wheel
|
07-11-2016, 08:56 PM | #4 |
Drives: '14 1LS Join Date: Apr 2014
Location: Mandeville
Posts: 2,166
|
I took a screen shot of the available offsets here you go guys. Would I need spacers for this? Would it for over brembos? Are spacers really safe ?
Sent from my iPhone using Tapatalk
__________________
Patiently waiting for my 2023 SS 1LE |
07-11-2016, 08:57 PM | #5 |
Drives: '14 1LS Join Date: Apr 2014
Location: Mandeville
Posts: 2,166
|
Sent from my iPhone using Tapatalk
__________________
Patiently waiting for my 2023 SS 1LE |
07-13-2016, 12:53 PM | #6 |
Drives: '14 1LS Join Date: Apr 2014
Location: Mandeville
Posts: 2,166
|
Bump
Sent from my iPhone using Tapatalk
__________________
Patiently waiting for my 2023 SS 1LE |
07-13-2016, 12:56 PM | #7 |
Svt lol
Drives: 2011 ss inferno orange blown Join Date: Jan 2012
Location: Topeka
Posts: 2,312
|
That might work. I would see what their return policy is worse case scenario get a set and test fit them if they work run them if not send them back.
__________________
plasti dip is not a mod.......and a cold air intake doesn't make you fast!
|
07-13-2016, 01:00 PM | #8 |
Cone Killer
Drives: 2012 SS Join Date: Dec 2013
Location: St. Albans, West Virginia
Posts: 832
|
If you were on coilovers and don't have a ton of camber at the knuckle, they would fit without spacers. Even then, it's tight. I have 20x10 +40 wheels on my car (on coilovers) and they clear, but just barely. I only have about 1.2 degrees of camber at the knuckle.
__________________
2012 Camaro SS - Sold
Selling off my remaining wheels, tires, 27mm front sway bar, and MGW shift knob. Get them out of my house before my wife puts me out! |
07-13-2016, 01:09 PM | #9 |
Drives: '14 1LS Join Date: Apr 2014
Location: Mandeville
Posts: 2,166
|
Well I do plan on lowering the car about an inch on BC Racing coilovers. Would the wheels being 19's instead of 20's give me more or less room? Also Burt do you have brembos?
Sent from my iPhone using Tapatalk
__________________
Patiently waiting for my 2023 SS 1LE |
07-13-2016, 01:42 PM | #10 |
Cone Killer
Drives: 2012 SS Join Date: Dec 2013
Location: St. Albans, West Virginia
Posts: 832
|
I do have Brembos, and being smaller I imagine it'll hurt clearance but only by a mm or less. Are you planning on getting camber plates?
__________________
2012 Camaro SS - Sold
Selling off my remaining wheels, tires, 27mm front sway bar, and MGW shift knob. Get them out of my house before my wife puts me out! |
07-13-2016, 06:21 PM | #11 |
Drives: '14 1LS Join Date: Apr 2014
Location: Mandeville
Posts: 2,166
|
I was eventually, probably once I get lowered. How much are you lowered?
Sent from my iPhone using Tapatalk
__________________
Patiently waiting for my 2023 SS 1LE |
|
|
|
|