12-15-2014, 09:40 AM | #1 |
BUMBL Z
|
Using factory Aux port & microphone with aftermarket radio
I've searched high and low, and cannot find a straight answer, wiring diagram, color codes, or any other information on how to do this. I'm going to be going aftermarket with my radio, and i know that you can reuse the factory usb via a usb to mini-usb cable (http://www.camaro5.com/forums/showth...74&postcount=4 for those who need this info). Also, if at all possible, in an effort to make this install look as factory as possible, is there any way i can tap the stock microphone in the homelink console for my aftermarket radio?
Does anyone have any information? thanks in advance
__________________
Sold: 2015 ZL1 M6, Rotofab Intake, LS3 throttle body, 2.55 Upper/9.17 Lower, Custom Camshaft, DMS Reinforced Brick, ID1050X, 1 7/8" Headers, ProSpeed HX/Reservoir, DSX Aux Pump/Flex Fuel Sensor, E85, McLeod RXT, BMR 1" Drop, 680rw 93/750rw E85, Tuned by CSP
Sold: 2010 2SS, some bolt ons, 415rwhp/400rwtq Last edited by spadz93; 12-15-2014 at 10:04 AM. |
12-17-2014, 02:00 PM | #2 |
BUMBL Z
|
nobody's attempted this? i find that hard to believe?
__________________
Sold: 2015 ZL1 M6, Rotofab Intake, LS3 throttle body, 2.55 Upper/9.17 Lower, Custom Camshaft, DMS Reinforced Brick, ID1050X, 1 7/8" Headers, ProSpeed HX/Reservoir, DSX Aux Pump/Flex Fuel Sensor, E85, McLeod RXT, BMR 1" Drop, 680rw 93/750rw E85, Tuned by CSP
Sold: 2010 2SS, some bolt ons, 415rwhp/400rwtq |
12-18-2014, 08:00 AM | #3 |
BUMBL Z
|
found it myself in a wiring info page. for anyone else interested in doing this, here's the wiring pin-outs:
Ground: Dark Green/White Left: Yellow Right: tan/white
__________________
Sold: 2015 ZL1 M6, Rotofab Intake, LS3 throttle body, 2.55 Upper/9.17 Lower, Custom Camshaft, DMS Reinforced Brick, ID1050X, 1 7/8" Headers, ProSpeed HX/Reservoir, DSX Aux Pump/Flex Fuel Sensor, E85, McLeod RXT, BMR 1" Drop, 680rw 93/750rw E85, Tuned by CSP
Sold: 2010 2SS, some bolt ons, 415rwhp/400rwtq |
03-20-2016, 06:11 PM | #4 |
Drives: 2014 2SS RS Coupe Join Date: Aug 2013
Location: Phoenix
Posts: 1,453
|
Update: cannot use factory microphone with aftermarket radio. I've done much testing and with my knowledge after converting factory mic plug to 3.5mm aux (headphone) it seems there's extremely bad interference with the factory mic on an aftermarket head unit. Microphone from factory has a proprietary impedance that will only work with mylink.
__________________
|
03-21-2016, 09:50 PM | #5 |
Drives: 2014 2SS RS Coupe Join Date: Aug 2013
Location: Phoenix
Posts: 1,453
|
Disregard previous post! Factory microphone works very well, there cannot be any interference in the system, you can't talk too loud either because it's very sensitive but it's a great microphone.
__________________
|
03-24-2016, 11:08 PM | #6 |
Got Boost?
Drives: 2011 1SS/RS M6 SLP TVS 2300 Join Date: Oct 2010
Location: San Diego, CA
Posts: 404
|
Looking at doing this, Where did you tap into those wires at?
__________________
2011 1SS/RS M6
MOD List: SLP 2300 Supercharged, Flowmaster AT Cat back, aux 4 guage cluster, 12" kicker sub and Kicker Zx400.1 amp, PFADT Lowering springs CAI Inc. CAI, Hurst Short throw shifter, JBA 1 7/8 Long tube headers. Future Mods: 416ci stroker. |
03-25-2016, 11:06 PM | #7 |
Drives: 2014 2SS RS Coupe Join Date: Aug 2013
Location: Phoenix
Posts: 1,453
|
http://www.camaro5.com/forums/attach...1&d=1458965033
Just wired to a 3.5mm mono plug (had to solder) and then used a blue and red wire to connect the mic, I used 2 pins also. I bought a rectifier (idk what that is) but it was from RadioShack and cut the pins off and solders the wires to those and then plugged the pins in the microphone harness
__________________
|
03-26-2016, 02:02 AM | #8 |
Got Boost?
Drives: 2011 1SS/RS M6 SLP TVS 2300 Join Date: Oct 2010
Location: San Diego, CA
Posts: 404
|
Gotcha, thanks for the pic.
Sent from my SM-G920V using Tapatalk
__________________
2011 1SS/RS M6
MOD List: SLP 2300 Supercharged, Flowmaster AT Cat back, aux 4 guage cluster, 12" kicker sub and Kicker Zx400.1 amp, PFADT Lowering springs CAI Inc. CAI, Hurst Short throw shifter, JBA 1 7/8 Long tube headers. Future Mods: 416ci stroker. |
05-24-2017, 09:59 AM | #9 | |
LEXi is Sassy and Classy
Drives: 2012 Camaro 2LT RS Boston Acoustic Join Date: Mar 2014
Location: Toronto, Ontario
Posts: 510
|
Quote:
I would too like to retain the in vehicle's mic. Thanks. |
|
03-30-2024, 04:05 PM | #10 |
Drives: Camaro Conv. 6.2 SS - 2014 Join Date: Jan 2018
Location: Germany
Posts: 9
|
Hi,
can someone explain in more detail how to use the original microphone for a aftermarket radio? Would be infinitely grateful! |
|
|
|
|