looking for opinions please - Page 2 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

ssrs2lt · 09-13-2015, 03:21 AM

Looks great

christianchevell · 09-13-2015, 08:50 AM

I like the way the heavy duty stickers mold down to zero at the edges. I installed a Mimousa wood grain on my car, they did not have one for the mylink yet and I was kind of annoyed that I could see edges on several of the pieces and the one around the steering by the buttons cracked from the bend angle. I did successfully remove the vents, and steering wheel and a few others and like the look now and it protects the stock pieces. How ever yes it was a PITA, I had to tear them apart then clean the excess tape/foam backing with my finger nails scraping then take a lot of time with goo-gone to use a rag to get the rest off. It did work with no damage to the car and was on for about a year or so. That kit looks nice, I would say though some pieces will look CHEESEY after you notice them for a while, like say the mylink piece by the a/c controls where they left cutouts for the symbols, and just to make something for it does not mean it looks the best. One thing I liked about the MIMOUSA kit they had armrest cover pads for the back seat that made it look nicer.

Good luck!

davesnever · 09-14-2015, 08:13 PM

Yeah I like it! It looks like a quality kit not like those cheap vinyl stencils.However I don't think every piece is a winner. I like the kickpanels for the doors, shifter,cupholder and stereo(center pieces)and doorhandles.But not diggin any of the vent pieces at all.

09-13-2015, 03:21 AM	#15
ssrs2lt Drives: too many Join Date: Jul 2013 Location: oh va pa ma tx Posts: 3,046	Looks great __________________

09-13-2015, 08:50 AM	#16
christianchevell old school chevy rodder Drives: 2013 2SS/RS Manual,DM exhaust,CRT Join Date: Jul 2012 Location: Oregon Posts: 5,587 View My Garage	I like the way the heavy duty stickers mold down to zero at the edges. I installed a Mimousa wood grain on my car, they did not have one for the mylink yet and I was kind of annoyed that I could see edges on several of the pieces and the one around the steering by the buttons cracked from the bend angle. I did successfully remove the vents, and steering wheel and a few others and like the look now and it protects the stock pieces. How ever yes it was a PITA, I had to tear them apart then clean the excess tape/foam backing with my finger nails scraping then take a lot of time with goo-gone to use a rag to get the rest off. It did work with no damage to the car and was on for about a year or so. That kit looks nice, I would say though some pieces will look CHEESEY after you notice them for a while, like say the mylink piece by the a/c controls where they left cutouts for the symbols, and just to make something for it does not mean it looks the best. One thing I liked about the MIMOUSA kit they had armrest cover pads for the back seat that made it look nicer. Good luck! __________________ 2021 Wild Cherry ZL1 A10, Sunroof, Data, Carbon, Nav, RotoFab Dry CAI, Elite x2, Borla ATK, Driveshaft shop

09-14-2015, 08:13 PM	#17
davesnever Drives: 2010 Camaro 2SS Join Date: Sep 2015 Location: Richmond Hill ,Ontario, Canada Posts: 780 View My Garage	Yeah I like it! It looks like a quality kit not like those cheap vinyl stencils.However I don't think every piece is a winner. I like the kickpanels for the doors, shifter,cupholder and stereo(center pieces)and doorhandles.But not diggin any of the vent pieces at all.